User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-27
ASUS ESC8000A-E11
The following items appear only when you set CAD Bus Timing User Controls to
[Manual].
AddrCmdSetup [0]
Allows you to setup time on CAD bus signals.
Configuration options: [0] – [39]
CsOdtSetup [0]
Allows you to setup time on CAD bus signals.
Configuration options: [0] – [39]
CkeSetup [0]
Allows you to setup time on CAD bus signals.
Configuration options: [0] – [39]
CAD Bus Drive Strength User Controls [Auto]
Allows you to set the CAD bus signals to Auto or Manual.
Configuration options: [Auto] [Manual]
The following items appear only when you set CAD Bus Drive Strength User Controls to
[Manual].
ClkDrvStren [Auto]
Configuration options: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0
Ohm] [24.0 Ohm] [20.0 Ohm]
AddrCmdDrvStren [Auto]
Configuration options: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0
Ohm] [24.0 Ohm] [20.0 Ohm]
Cs0dtDrvStren [Auto]
Configuration options: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0
Ohm] [24.0 Ohm] [20.0 Ohm]
CkeDrvStren [Auto]
Configuration options: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0
Ohm] [24.0 Ohm] [20.0 Ohm]
Data Bus Configuration
Data Bus Configuration User Controls [Auto]
Allows you to specify the mode for drive strength.
Configuration options: [Auto] [Manual]
The following items appear only when you set Data Bus Configuration User Controls to
[Manual].
RttNom [Auto]
Configuration options: [Rtt_Nom Disable] [RZQ/4] [RZQ/2] [RZQ/6]
[RZQ/1] [RZQ/5] [RZQ/3] [RZQ/7] [Auto]
RttWr [Auto]
Configuration options: [Dynamic ODT Off] [RZQ/2] [RZQ/1] [Hi-Z]
[RZQ/3] [Auto]
RttPark [Auto]
Configuration options: [Rtt_PARK Disable] [RZQ/4] [RZQ/2] [RZQ/6]
[RZQ/1] [RZQ/5] [RZQ/3] [RZQ/7] [Auto]