User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-21
ASUS ESC8000A-E11
4-link xGMI max speed [Auto]
Configuration options: [8.533Gbps] [9.6Gbps] [10.667Gbps] [11Gbps] [12Gbps]
[13Gbps] [14Gbps] [15Gbps] [16Gbps] [17Gbps] [18Gbps] [19Gbps] [20Gbps]
[21Gbps] [22Gbps] [23Gbps] [24Gbps] [25Gbps] [Auto]
3-link xGMI max speed [Auto]
Configuration options: [8.533Gbps] [9.6Gbps] [10.667Gbps] [11Gbps] [12Gbps]
[13Gbps] [14Gbps] [15Gbps] [16Gbps] [17Gbps] [18Gbps] [19Gbps] [20Gbps]
[21Gbps] [22Gbps] [23Gbps] [24Gbps] [25Gbps] [Auto]
xGMI TXEQ Mode [Auto]
Allows you to select the XGMI TXEQ/RX vetting mode.
Configuration options: [TXEQ_Disabled] [TXEQ_Lane] [TXEQ_Link] [TXEQ_
RX_Vet] [Auto]
xGMI 18GACOFC [Auto]
Allows you to enable or disable the 18GACOFC control.
Configuration options: [Auto] [Enable] [Disable]
Disable DF to external IP SyncFloodPropagation [Auto]
Allows you to enable or disable Error propagation to UMC or any downstream slaves
e.g., FCH. Use this to avoid reset in failure scenario.
Configuration options: [Sync flood disabled] [Sync flood enabled] [Auto]
Disable DF sync flood propagation [Auto]
Allows you to enable or disable propagation from PIE to other DF components and
eventually to SDP ports.
Configuration options: [Sync flood disabled] [Sync flood enabled] [Auto]
Freeze DF module queues on error [Auto]
Allows you to enable or disable freezing of all DF queues on error and also forces a
sync flood on HWA even if MCAs are disabled.
Configuration options: [Disabled] [Enabled] [Auto]
CC6 memory region encryption [Auto]
Allows you to control whether or not the CC6 save/restore memory is encrypted.
Configuration options: [Disabled] [Enabled] [Auto]
System probe filter [Auto]
Allows you to control whether or not the probe filter is enabled. Has no effect on parts
where the probe filter is fuse disabled.
Configuration options: [Disabled] [Enabled] [Auto]
Memory Clear [Auto]
Allows you to enable or disable memory clear. When this item is set to [Disabled],
BIOS does not implement MemClear after memory training (only if non-ECC DIMMs
are used).
Configuration options: [Disabled] [Enabled] [Auto]
PSP error injection support [False]
Configuration options: [False] [True]