User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-20
Chapter 3: BIOS Setup
The following item appears only when ACPI SLIT Distance Control is set to [Auto].
ACPI SLIT remote relative distance [Auto]
Allows you to set the remote socket distance for 2P systems as near (2.8) or
far (3.2).
Configuration options: [Near] [Far] [Auto]
The following items appear only when ACPI SLIT Distance Control is set to [Manual].
ACPI SLIT same socket distance [C]
Specify the distance to other physical domains within the same socket.
ACPI SLIT remote socket distance [20]
Specify the distance to domains the remote socket.
ACPI SLIT local SLink distance [32]
Specify the distance to an SLink domain on the same socket.
ACPI SLIT remote SLink distance [3C]
Specify the distance to an SLink domain on the other socket.
ACPI SLIT local inter-SLink distance [FF]
Specify the distance between two SLink domains on the same socket.
ACPI SLIT remote inter-SLink distance [FF]
Specify the distance between two SLink domains, each on a different socket.
Link
GMI encryption control [Auto]
Allows you to control the GMI link encryption.
Configuration options: [Disabled] [Enabled] [Auto]
xGMI encryption control [Auto]
Allows you to control the xGMI link encryption.
Configuration options: [Disabled] [Enabled] [Auto]
CAKE CRC perf bounds control [Auto]
Configuration options: [Auto] [Manual]
The following item appears only when CAKE CRC perf bounds control is set to [Manual].
CAKE CRC perf bounds [100]
This item specifies the amount of performance loss that is acceptable to enable
CRC protection. Units are in 0.00001%, RangeL disabled (0) - 10% (1000000).
xGMI Link Configuration [Auto]
Allows you to configure the number of xGMI2 links used on a multi-socket
system.
Configuration options: [Auto] [2 xGMI Links] [3 xGMI Links] [4 xGMI Links]