User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-18
Chapter 3: BIOS Setup
Amount of Memory to Cover [0]
Allows you to specify MB of System Memory to be covered in Hex.
SMEE [Auto]
Allows you to enable or disable secure memory encryption control.
Configuration options: [Disabled] [Enabled] [Auto]
Action on BIST Failure [Auto]
Allows you to set action to take when a CCD BIST failure is detected.
Configuration options: [Do Nothing] [Down-CCD] [Auto]
Fast Short REP MOVSB (FSRM) [Auto]
Can be set to disabled for analysis purposes as long as OS supports it.
Configuration options: [Disabled] [Enabled] [Auto]
Enhanced REP MOVSB/STOSB (ERMSB) [Auto]
Can be set to disabled for analysis purposes as long as OS supports it.
Configuration options: [Disabled] [Enabled] [Auto]
REP-MOV/STOS Streaming [Disabled]
Allows REP-MOVS/STOS to use non-caching streaming stores for large sizes.
Configuration options: [Disabled] [Enabled]
IBS hardware workaround [Auto]
Set this option if using IBS execution sampling without software workaround for
erratum 1,285. May impact performance.
Configuration options: [Auto] [Enabled]
DF Common Options
Scrubber
DRAM scrub time [Auto]
Allows you to set a number of hours to scrub memory.
Configuration options: [Disabled] [1 hour] [4 hours] [8 hours] [16 hours] [24
hours] [48 hours] [Auto]
Poison scrubber control [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
Redirect scrubber control [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
Redirect scrubber limit [Auto]
Configuration options: [2] [4] [8] [Infinite] [Auto]
Periodic Directory Rinse [Auto]
Configuration options: [Disabled] [Enabled] [Auto]