User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-17
ASUS ESC8000A-E11
The following item appears only when SEV-ES ASID Space Limit Control is set to
[Manual].
SEV-ES ASID Space Limit [1]
SEV Vms using ASIDs below the SEV-ES ASID Space Limit must enable the SEV-ES
feature. ASIDs from SEV-ES ASID Space Limit to (SEV ASID Count + 1) can only be
used with SEV VMs. If this field is set to (SEV ASID Count + 1), all ASIDs are forced to
be SEV-ES ASIDs. Hence, the valid values for this field is 1 - (SEV ASID Count + 1).
Streaming Stores Control [Auto]
Allows you to enable or disable the streaming stores functionality.
Configuration options: [Disabled] [Enabled] [Auto]
Local APIC Mode [Auto]
Configuration options: [Compatibility] [xAPIC] [x2APIC] [Auto]
ACPI _CST C1 Declaration [Auto]
Determines whether or not to declare the C1 state to the OS.
Configuration options: [Disabled] [Enabled] [Auto]
MCA error thresh enable [Auto]
Allows you to enable or disable MCA error thresholding.
Configuration options: [False] [True] [Auto]
The following item appears only when MCA error thresh enable is set to [True].
MCA error thresh count [FF5]
Allows you to set the effective error threshold count = 4095(0xFFF) - <this value> (e.g.,
the default value of 0xFF5 results in a threshold of 10).
SMU and PSP Debug Mode [Auto]
When this option is set to [Enabled], specific uncorrected errors detected by the PSP
FW or SMU FW will hang and not reset the system.
Configuration options: [Disabled] [Enabled] [Auto]
PPIN Opt-in [Auto]
Allows you to enable or disable the PPIN feature.
Configuration options: [Disabled] [Enabled] [Auto]
SNP Memory (RMP Table) Coverage [Auto]
Setting this option to [Enabled] will cover the entire system’s memory.
Configuration options: [Disabled] [Enabled] [Custom] [Auto]
The following item appears only when SNP Memory (RMP Table) Coverage is set to
[Custom].
Amount of Memory to Cover [0]
Allows you to specify MB of System Memory to be covered in Hex.