User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-58
Chapter 3: BIOS Setup
SATA Partial State Capability [Enabled]
Indicates whether Host Bus Adapter (HBA) can support transitions to the partial
state.
Configuration options: [Disabled] [Enabled]
SATA FIS Based Switching [Enabled]
Indicates whether Host Bus Adapter (HBA) can support port multiplier FIS-
based switching.
Configuration options: [Disabled] [Enabled]
SATA Command Completion Coalescing Support [Disabled]
Indicates whether Host Bus Adapter (HBA) can support command completion
coalescing.
Configuration options: [Disabled] [Enabled]
SATA Slumber State Capability [Enabled]
Indicates whether Host Bus Adapter (HBA) can support transitions to the
slumber state.
Configuration options: [Disabled] [Enabled]
SATA Target Support 8 Devices [Disabled]
Indicates whether SATA target support 8 devices function.
Configuration options: [Disabled] [Enabled]
Generic Mode [Disabled]
Allows you to SATA disable Generic Mode.
Configuration options: [Disabled] [Enabled]
SATA AHCI Enclosure [Disabled]
Allows you to enable or disable SATA AHCI Enclosure Management.
Configuration options: [Disabled] [Enabled]
SATA SGPIO 0 [Disabled]
Allows you to enable or disable SATA Serial General Purpose Input/Output
(SGPIO) 0.
Configuration options: [Disabled] [Enabled]
SB FUSION DEBUG Configuration
The items in this submenu contains options for SB FUSION DEBUG Configuration.
TimerTick Tracking [Disabled]
Configuration options: [Disabled] [Enabled]
Clock Interrupt Tag [Disabled]
Configuration options: [Disabled] [Enabled]
SB MISC DEBUG Configuration
The items in this submenu contains options for SB DEBUG Configuration.
SB Clock Spread Spectrum [Enabled]
Allows you to enable or disable CG1_PLL Spread Spectrum.
Configuration options: [Disabled] [Enabled]
HPET In SB [Enabled]
Allows you to enable or disable the HPET Function Switch.
Configuration options: [Disabled] [Enabled]
MsiDis in HPET [Enabled]
Expose MSI capability in HPET Capability register.
Configuration options: [Disabled] [Enabled]