User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe riser card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II card
- 2.6.3 Installing an HBA/RAID card
- 2.6.4 Installing an expansion card to the rear left PCIe expansion card bracket (on select models)
- 2.6.5 Installing an expansion card to the rear right PCIe expansion card bracket (on select models)
- 2.6.6 Installing an OCP 3.0 card to the rear right OCP 3.0 socket board (on select models)
- 2.6.7 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Installing GPU cards
- 2.10 Installing Optional Kits
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Serial Port Console Redirection
- 3.5.7 CPU Configuration
- 3.5.8 PCI Subsystem Settings
- 3.5.9 USB Configuration
- 3.5.10 Network Stack Configuration
- 3.5.11 CSM Configuration
- 3.5.12 NVMe Configuration
- 3.5.13 SATA Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Tls Auth Configuration
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Save & Exit menu
- 3.11 Event Logs menu
- 3.12 Server Mgmt menu
- Chapter 4: Driver Installation
- Appendix
3-53
ASUS ESC8000A-E11
3.5.11 CSM Configuration
CSM Support [Enabled]
This option allows you to enable or disable CSM Support.
Configuration options: [Enabled] [Disabled]
The following item appears only when CSM Support is set to [Enabled].
GateA20 Active [Upon Request]
This allows you to set the GA20 option.
Configuration options: [Upon Request] [Always]
Option ROM Messages [Force BIOS]
This allows you to set the display mode for option ROM.
Configuration options: [Force BIOS] [Keep Current]
INT19 Trap Response [Immediate]
The BIOS reaction on INT19 trapping by Option ROM.
[Immediate] Execute the trap right away.
[Postponed] Execute the trap during legacy boot.
HDD Connection Order [Adjust]
This option allows you to select the HDD Connection Order. Some OS require HDD
handles to be adjusted, i.e. OS is installed on drive 80h.
Configuration options: [Adjust] [Keep]
Boot Option filter [UEFI and Legacy]
This option allows you to control the Legacy/UEFI ROMs priority.
Configuration options: [UEFI and Legacy] [Legacy only] [UEFI only]
Ipv6 HTTP Support [Disabled]
Enables or disables the Ipv6 HTTP Boot Support. If disabled, Ipv6 HTTP boot option
will not be created.
Configuration options: [Disabled] [Enabled]
PXE boot wait time [0]
Set the wait time to press ESC key to abort the PXE boot. Use the <+> or <-> to adjust
the value. The values range from 0 to 5.
Media detect count [1]
Set the number of times presence of media will be checked. Use the <+> or <-> to
adjust the value. The values range from 1 to 50.