User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe expansion card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II or RAID card
- 2.6.3 Installing the Cache Vault Power Module
- 2.6.4 Installing an expansion card to the rear PCIe expansion card slots (on select models)
- 2.6.5 Installing an OCP 3.0 card to the rear OCP 3.0 socket board (on select models)
- 2.6.6 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Rail kit options
- Chapter 3: Motherboard Information
- Chapter 4: BIOS Setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Performance Tuning menu
- 4.5 Advanced menu
- 4.5.1 Trusted Computing
- 4.5.2 ACPI Settings
- 4.5.3 Redfish Host Interface Settings
- 4.5.4 Onboard LAN Configuration
- 4.5.5 Serial Port Console Redirection
- 4.5.6 SIO Configuration
- 4.5.7 PCI Subsystem Settings
- 4.5.8 USB Configuration
- 4.5.9 Network Stack Configuration
- 4.5.10 NVMe Configuration
- 4.5.11 APM Configuration
- 4.5.12 T1s Auth Configuration
- 4.5.13 Third-party UEFI driver configurations
- 4.6 Platform Configuration menu
- 4.7 Socket Configuration menu
- 4.8 Security menu
- 4.9 Boot menu
- 4.10 Tool menu
- 4.11 Event Logs menu
- 4.12 Server Mgmt menu
- 4.13 Save & Exit menu
- Chapter 5: RAID Configuration
- Appendix
4-15
ASUS ESC8000-E11P
4.5.6 SIO Configuration
Logical Devices state on the left side of the control, reflects the current Logical Device
state. Changes made during Setup Session will be shown after you restart the system.
[*Active*] Serial Port 1 / [*Active*] Serial Port 2
Allows you to view and set basic properties of the SIO Logical device.
Use This Device [Enabled]
Allows you to enable or disable this Logical Device.
Configuration options: [Disabled] [Enabled]
The following item appears only when Use This Device is set to [Enabled].
Disabling SIO Logical Devices may have unwanted side effects. PROCEED WITH
CAUTION.
Possible: [Use Automatic Settings]
Allows the user to change the device resource settings. New settings will be
reflected no this setup page after system restarts.
Configuration options: [Use Automatic Settings] [IO=3F8h; IRQ=4; DMA;]
[IO=3F8h; IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA;] [IO=2F8h; IRQ=3, 4, 5, 7, 9,
10, 11, 12; DMA;] [IO=3E8h; IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA;] [IO=2E8h;
IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA;]