User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slots
- 2.6.1 Installing an expansion card to the front PCIe expansion card bracket (on select models)
- 2.6.2 Installing an ASUS PIKE II or RAID card
- 2.6.3 Installing the Cache Vault Power Module
- 2.6.4 Installing an expansion card to the rear PCIe expansion card slots (on select models)
- 2.6.5 Installing an OCP 3.0 card to the rear OCP 3.0 socket board (on select models)
- 2.6.6 (optional) Installing the PFR module
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Rail kit options
- Chapter 3: Motherboard Information
- Chapter 4: BIOS Setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Performance Tuning menu
- 4.5 Advanced menu
- 4.5.1 Trusted Computing
- 4.5.2 ACPI Settings
- 4.5.3 Redfish Host Interface Settings
- 4.5.4 Onboard LAN Configuration
- 4.5.5 Serial Port Console Redirection
- 4.5.6 SIO Configuration
- 4.5.7 PCI Subsystem Settings
- 4.5.8 USB Configuration
- 4.5.9 Network Stack Configuration
- 4.5.10 NVMe Configuration
- 4.5.11 APM Configuration
- 4.5.12 T1s Auth Configuration
- 4.5.13 Third-party UEFI driver configurations
- 4.6 Platform Configuration menu
- 4.7 Socket Configuration menu
- 4.8 Security menu
- 4.9 Boot menu
- 4.10 Tool menu
- 4.11 Event Logs menu
- 4.12 Server Mgmt menu
- 4.13 Save & Exit menu
- Chapter 5: RAID Configuration
- Chapter 6: Driver Installation
- Appendix
4-18
Chapter 4: BIOS Setup
4.5.9 Network Stack Configuration
Network Stack [Enabled]
Enables or disables the UEFI network stack.
Configuration options: [Disabled] [Enabled]
The following items appear only when Network Stack is set to [Enabled].
IPv4 PXE Support [Disabled]
Enables or disables the IPv4 PXE Boot Support. If disabled, IPv4 PXE boot support will
not be available.
Configuration options: [Disabled] [Enabled]
IPv4 HTTP Support [Disabled]
Enables or disables the IPv4 HTTP Boot Support. If disabled, IPv4 HTTP boot support
will not be available.
Configuration options: [Disabled] [Enabled]
IPv6 PXE Support [Disabled]
Enables or disables the IPv6 PXE Boot Support. If disabled, IPv6 PXE boot support will
not be available.
Configuration options: [Disabled] [Enabled]
IPv6 HTTP Support [Disabled]
Enables or disables the IPv6 HTTP Boot Support. If disabled, IPv6 HTTP boot support
will not be available.
Configuration options: [Disabled] [Enabled]
PXE boot wait time [0]
Set the wait time to press ESC key to abort the PXE boot. Use the <+> or <-> to adjust
the value. The values range from 0 to 5.
Media detect count [1]
Set the number of times presence of media will be checked. Use the <+> or <-> to
adjust the value. The values range from 1 to 50.