User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- Chapter 3: Motherboard Information
- Chapter 4: BIOS Setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Performance Tuning menu
- 4.5 Advanced menu
- 4.5.1 Trusted Computing
- 4.5.2 ACPI Settings
- 4.5.3 Redfish Host Interface Settings
- 4.5.4 Onboard LAN Configuration
- 4.5.5 UEFI Variables Protection
- 4.5.6 Serial Port Console Redirection
- 4.5.7 SIO Configuration
- 4.5.8 PCI Subsystem Settings
- 4.5.9 USB Configuration
- 4.5.10 Network Stack Configuration
- 4.5.11 NVMe Configuration
- 4.5.12 APM Configuration
- 4.5.13 T1s Auth Configuration
- 4.5.14 Third-party UEFI driver configurations
- 4.6 Platform Configuration menu
- 4.7 Socket Configuration menu
- 4.8 Security menu
- 4.9 Boot menu
- 4.10 Tool menu
- 4.11 Event Logs menu
- 4.12 Server Mgmt menu
- 4.13 Save & Exit menu
- Chapter 5: RAID Configuration
- Chapter 6: Driver Installation
- Appendix
3-3
Jumpers Page
1. Clear RTC RAM (3-pin CLRTC1) 3-6
2. DMLAN setting (3-pin DM_IP_SEL1) 3-7
3. Baseboard Management Controller setting (3-pin BMC_EN1)
3-7
4. LANNCSI_SEL setting (3-pin LANNCSI_SEL1) 3-8
5. Smart Ride Through (SmaRT) setting (3-pin SMART_PSU1) 3-8
6. ME Firmware Force Recovery setting (3-pin ME_RCVR1) 3-9
7. PCH_MFG1 setting (3-pin PCH_MFG1) 3-9
8. RM debug setting (3-pin RM_DEBUG1) 3-10
Onboard LEDs Page
1. Baseboard Management Controller LED (BMCLED1) 3-21
2. Catastrophic Error LED (CATERR1) 3-21
3. Standby Power LED (SBPWR1) 3-22
Internal connectors Page
1. MCIOPCIE connectors (MCIOPCIE1-13) 3-11
2. CPU fan connectors (4-pin CPU_FAN1-2) 3-11
3. System fan connectors (10-pin SYSFAN1-6) 3-12
4. CPLD JTAG connector (6-pin CPLD_JTAG1)
3-12
5. microSD card slot (MSD1) 3-13
6. Serial port connector (10-1-pin COM1) 3-13
7. REAR_CON1 connector (10-pin REAR_CON1) 3-14
8. OCP3.0 sideband signal connector (12-pin OCP_SIDE1) 3-14
9. BF connector (BF_CON1-2) 3-15
10. NCSI_CON connector (NCSI_CON1-2) 3-15
11. System management bus connector (5-1-pin SMBUS2) 3-16
12. Leak detection sensor connector (4-pin WL_CON1) 3-16
13. BMC debug UART connector (3-pin BMC_DEBUGUART1) 3-17
14. Platform Firmware Resilience (PFR) module connector (ROT_CON1) 3-17
15. TPM connector (14-1-pin TPM1) 3-18
16. VROC_KEY connector (4-pin VROC_KEY1) 3-18
17. System power connectors (PWR1-4) 3-19
18. System power connectors (PWR5-6) 3-19
19. Switchboard and riser power connectors (SW_PWR1-2; RISER_PWR1-2) 3-20