User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Onboard LAN Configuration
- 3.5.7 Serial Port Console Redirection
- 3.5.8 CPU Configuration
- 3.5.9 PCI Subsystem Settings
- 3.5.10 USB Configuration
- 3.5.11 Network Stack Configuration
- 3.5.12 CSM Configuration
- 3.5.13 NVMe Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Third-party UEFI driver configurations
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Event Logs menu
- 3.11 Server Mgmt menu
- 3.12 Exit menu
- Chapter 4: Driver Installation
- Appendix
3-43
ASUS ESC N4A-E11
The following items appear only when Socket-0 P0 NTB Enable is set to [Enabled].
Socket-0 P0 Start Lane [0]
Allows you to set the NTB Start Lane on Socket-0 P0 Link.
Configuration options: [0] - [15]
Socket-0 P0 End Lane [15]
Allows you to set the NTB End Lane on Socket-0 P0 Link.
Configuration options: [0] - [15]
Socket-0 P0 Link Speed [Auto]
Allows you to select the Link Speed for Socket-0 P0.
Configuration options: [Max Speed] [Gen 1] [Gen 2] [Gen 3] [Auto] [Gen 4]
Socket-0 P0 NTB Mode [Auto]
Allows you to select the NTB Mode for Socket-0 P0 Link.
Configuration options: [Auto] [NTB Disabled] [NTB Primary] [NTB Secondary]
Socket-0 P1 NTB Enable [Auto]
Allows you to enable NTB on Socket-0 P1 Link.
Configuration options: [Auto] [Enable]
The following items appear only when Socket-0 P1 NTB Enable is set to [Enabled].
Socket-0 P1 Start Lane [32]
Allows you to set the NTB Start Lane on Socket-0 P1 Link.
Configuration options: [32] - [47]
Socket-0 P1 End Lane [47]
Allows you to set the NTB End Lane on Socket-0 P1 Link.
Configuration options: [32] - [47]
Socket-0 P1 Link Speed [Auto]
Allows you to select the Link Speed for Socket-0 P1.
Configuration options: [Max Speed] [Gen 1] [Gen 2] [Gen 3] [Auto] [Gen 4]
Socket-0 P1 NTB Mode [Auto]
Allows you to select the NTB Mode for Socket-0 P1 Link.
Configuration options: [Auto] [NTB Disabled] [NTB Primary] [NTB Secondary]
Socket-0 P2 NTB Enable [Auto]
Allows you to enable NTB on Socket-0 P2 Link.
Configuration options: [Auto] [Enable]
The following items appear only when Socket-0 P2 NTB Enable is set to [Enabled].
Socket-0 P2 Start Lane [80]
Allows you to set the NTB Start Lane on Socket-0 P2 Link.
Configuration options: [80] - [95]