User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- Chapter 3: BIOS Setup
- 3.1 Managing and updating your BIOS
- 3.2 BIOS setup program
- 3.3 Main menu
- 3.4 Performance Tuning menu
- 3.5 Advanced menu
- 3.5.1 Trusted Computing
- 3.5.2 PSP Firmware Versions
- 3.5.3 Redfish Host Interface Settings
- 3.5.4 AMD CBS
- 3.5.5 APM Configuration
- 3.5.6 Onboard LAN Configuration
- 3.5.7 Serial Port Console Redirection
- 3.5.8 CPU Configuration
- 3.5.9 PCI Subsystem Settings
- 3.5.10 USB Configuration
- 3.5.11 Network Stack Configuration
- 3.5.12 CSM Configuration
- 3.5.13 NVMe Configuration
- 3.5.14 AMD Mem Configuration Status
- 3.5.15 Third-party UEFI driver configurations
- 3.6 Chipset menu
- 3.7 Security menu
- 3.8 Boot menu
- 3.9 Tool menu
- 3.10 Event Logs menu
- 3.11 Server Mgmt menu
- 3.12 Exit menu
- Chapter 4: Driver Installation
- Appendix
3-31
ASUS ESC N4A-E11
Target Static Lane Value [0]
Configuration options: [0] - [9]
Worst Case Margin Granularity [Per Chip Select]
Configuration options: [Per Chip Select] [Per Nibble]
Read Voltage Sweep Step Size [1]
This option determines the step size for Read Data Eye voltage sweep.
Configuration options: [1] [2] [4]
Read Timing Sweep Step Size [1]
This option supports step size for Read Data Eye.
Configuration options: [1] [2] [4]
Write Voltage Sweep Step Size [1]
This option determines the step size for write Data Eye voltage sweep.
Configuration options: [1] [2] [4]
Write Timing Sweep Step Size [1]
This option supports step size for write Data Eye.
Configuration options: [1] [2] [4]
Memory Healing BIST [Disabled]
Allows you to enable a full memory test. The testing will increase the boot time.
BIOS mem BIST tests the full memory after training. Failing memory will be
repaired using soft or hard PPR depending on the PPC configuration. The test
will take 3 minutes per 16GN of installed memory. Self-Healing BIST runs the
JEDEC DRAM self healing if the device supports the feature. The DRAM will
do a hard repair for failing memory. The test will take 10 seconds per memory
rank per channel.
Configuration options: [Disabled] [BIOS Mem BIST] [Self-Healing Mem BIST]
[BIOS and Self-Healing Mem BIST]
The following items appear only when Memory Healing BIST is set to [BIOS Mem BIST].
Mem BIST Test Select [Vendor Tests Enabled]
Select the vendor specific tests to use with BIOS memory healing BIST.
Configuration options: [Vendor Tests Enabled] [Vendor Tests Disabled] [All
Tests - All Vendors]
Mem BIST Post Package Repair Type [Soft Repair]
For DRAM errors found in the BIOS memory BIST select the repair type, soft,
hard, or test only and do not attempt to repair.
Configuration options: [Soft Repair] [Hard Repair] [No Repairs - Test only]
NBIO Common Options
IOMMU [Disabled]
Allows you to enable or disable IOMMU.
Configuration options: [Disabled] [Enabled] [Auto]
DMAr Support [Auto]
Allows you to enable DMAr system protection during POST.
Configuration options: [Disable] [Enable] [Auto]
The following item appears only when Enable AER Cap is set to [Auto] or [Enable].