User's Manual
Table Of Contents
- ご注意
- Chapter 1
- 製品の概要
- Chapter 2
- UEFI BIOS情報
- 2.1 UEFI BIOS管理更新
- 2.2 UEFI BIOS Utility
- 2.3 メインメニュー
- 2.4 Ai Tweaker メニュー
- 2.4.1 Ai Overclock Tuner [Auto]
- 2.4.2 Memory Clock [Auto]
- 2.4.3 EPU Power Saving Mode [Disabled]
- 2.4.4 OC Tuner
- 2.4.5 DRAM Timing Control
- 2.4.6 CPU Offset Mode Sign [+]
- 2.4.7 CPU Voltage [Offset Mode]
- 2.4.8 VDDNB Offset Mode Sign [+]
- 2.4.9 VDDNB Voltage [Auto]
- 2.4.10 DRAM Voltage [Auto]
- 2.4.11 SB 1.1V Voltage [Auto]
- 2.4.12 APU1.8V Voltage [Auto]
- 2.4.13 APU 1.05V Voltage [Auto]
- 2.4.14 Load Line Calibration [Auto]
- 2.4.15 APU Spread Spectrum [Auto]
- 2.5 アドバンスドメニュー
- 2.6 モニターメニュー
- 2.7 ブートメニュー
- 2.8 ツールメニュー
- 2.9 終了メニュー
vi
ご注意
FederalCommunicationsCommissionStatement(原文)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit dierent from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
CanadianDepartmentofCommunicationsStatement(原文)
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
This class B digital apparatus complies with Canadian ICES-003.
本機は電気製品または電子装置であり、地域のゴミと一緒に捨てられません。また、本機のコン
ポーネントはリサイクル性を考慮した設計を採用しております。なお、廃棄の際は地域の条例等
の指示に従ってください。
本機に装着されているボタン型電池には水銀が含まれています。通常ゴミとして廃棄しないで
ください。
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
ASUS REACH website at http://csr.asus.com/english/REACH.htm.