Specifications

DS300f G2 Series User Manual
149
vIewInG IScSI Portal InformatIon (clu)
To view information for an iSCSI target port:
1. From the Main Menu, highlight iSCSI Management and press Enter.
2. Highlight iSCSI Portals and press Enter.
The list of portals appears.
3. Highlight the port you want to see and press Enter.
The portal information screen displays. Information includes:
• PortalID
–Portalnumber.Startsat0.
• TcpPort–TCPportnumber.3260isthedefaultandrecommendednumber.
• DHCP–Enabledordisabled.*
DHCPiscurrentlysupportedonlyforIPv4.
• AssociatedType–PHY,VLAN,orTrunk.
• ControllerID –RAIDcontrollerID,1or2.
• PortID–PhysicalportontheRAIDcontroller,1to4.
• InterfaceName–devicename.
• ProtocolFamily –IPv4orIPv6.*
• PrimaryIP–PrimaryIPaddressofthisportal.*
• Gateway -GatewayIPaddressofthisportal*
• PrimaryIPMask–Subnetmaskofthisportal.*
• AssignedTarget–0isthedefaulttarget.Thenumberoftargetsavailabledepends
onhowmanytargetsyoucreate.SeeAddingiSCSITargets(CLU)below.
Items marked with an asterisk (*) are adjustable under "Making iSCSI Portal Settings (CLU)" on page
149.
aDDInG IScSI PortalS (clu)
ASUS DS300f G2 supports up to 32 iSCSI portals. Each iSCSI portal can belong to a different VLAN for a
maximum of 32 VLANs.
Ifyouplantoassociatethenewportalwithatrunk,createthetrunkrst.See "Adding iSCSI Trunks (CLU)" on
page 153.
For more information about iSCSI VLANs, see "iSCSI on a VLAN" on page <?>.
To add an iSCSI portal:
1. From the Main Menu, highlight iSCSI Management and press Enter.
2. Highlight iSCSI Portals and press Enter.
The list of iSCSI Portals displays.
3. Highlight Create New Portal and press Enter.
4. Highlight AssociatedType and press the Spacebar to toggle through Physical, VLAN, and Trunk.
5. If you chose:
• PHY
–ChooseaControllerID(1or2)andaPortID(1to4).
• Trunk–ChooseaTrunkID(1to8).
To change an ID number, highlight the item, press Backspace to delete the current ID and type a new
ID.
6. If you use Associated PHY, highlight EnableVLAN and press the Spacebar to toggle between Enable and
Disable. If you choose Enable, enter a Vlan Tag (1 to 4094).
To change a value, highlight the item, press Backspace to delete the current value and type a new value.
7. Highlight Save Settings and press Enter.
The new Portal is added to the list.
makInG IScSI Portal SettInGS (clu)
To make portal settings:
1. From the Main Menu, highlight iSCSI Management and press Enter.
2. Highlight iSCSI Portals and press Enter.
The list of portals displays.
3. Highlight the portal you want to change and press Enter.
The portal information screen displays.
4. Highlight iSCSI Portal Settings and press Enter.
5. Make changes as needed.
• DHCP
–Enabledordisabled
DHCPiscurrentlysupportedonlyforIPv4.
• ProtocolFamily–IPv4orIPv6
• PrimaryIP–PrimaryIPaddressofthisportal
• PrimaryIPMask–Subnetmaskofthisportal
• Gateway -GatewayIPaddressofthisportal