SYSTEM BOARD D1260 USER'S MANUAL
Are there ... ... any technical problems or other questions you would like to be clarified? Please contact: • your sales partner • your sales outlet You will find further information in the manual "Safety, Guarantee and Ergonomics". The latest information on our products, tips, updates, etc., can be found on the Internet under: http://www.fujitsu-siemens.
Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. Este manual ha sido impreso sobre papel reciclado. Questo manuale è stato stampato su carta da riciclaggio. Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt. Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr./Order No.
Introduction Features SYSTEM BOARD D1260 Hardware Setup BIOS Setup User's Manual November 2000 edition
Copyright ã Fujitsu Siemens Computers GmbH 2000 Intel, Pentium and Celeron are registered trademarks and MMX and OverDrive are trademarks of Intel Corporation, USA. Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation. PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc. All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged.
CONTENTS 1. INTRODUCTION ............................................................................. 5 1.1 How This Manual Is Organized .................................................. 5 1.2 Item Checklist ............................................................................. 5 2. FEATURES ........................................................................................ 8 2.1 CUR-DLSR Motherboard ........................................................... 6 2.1.1 Specifications ...........
CONTENTS 4.3 Main Menu ................................................................................ 43 4.3.1 Primary & Secondary Master/Slave .............................. 44 4.3.2 Keyboard Features ......................................................... 47 4.4 Advanced Menu ........................................................................ 49 4.4.1 Chip Configuration ........................................................ 50 4.4.2 I/O Device Configuration .....................................
FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
1. INTRODUCTION 1.1 How This Manual Is Organized This manual is divided into the following sections: 1. INTRODUCTION 2. FEATURES 3. HARDWARE SETUP 4. BIOS SETUP 5. SOFTWARE SETUP 6. SOFTWARE REFERENCE 7. APPENDIX Manual information and checklist Product information and specifications Instructions on setting up the motherboard.
2. FEATURES 2.1 D1260 CUR-DLSR Motherboard The D1260 CUR-DLSR motherboard is designed primarily for multi-server environments to optimize available space without sacrificing performance. Powered by dual Intel® Pentium® III processors, the CUR-DLSR efficiently complies with today’s demand for a high-integration server. 2.1.1Specifications 2.
2. FEATURES • • • • Wake-Up Support: Supports Wake-On-LAN and Wake-On-Ring, and BIOS Wake-Up. ISA Multi-I/O: Provides two high-speed UART compatible serial ports and one parallel port with EPP and ECP capabilities. Around-the-Clock Intrusion Detection: Chassis intrusion circuitry can log chassis open events into LDSM.
2. FEATURES 2.1.2Performance • • • 2. FEATURES Specifications • • • 8 UltraPerformance: Onboard Ultra160/Ultra3 dual channel SCSI controller with two connectors that support 30 Ultra160/Ultra3 SCSI devices in two channels. Dual Speeds: CPU frequency can operate at either 133MHz or 100MHz depending on the CPU installed. High-Speed Data Transfer Interface: SCSI transfers using Ultra160/Ultra3 dual channel SCSI controller can handle rates up to 160MB/s or 80MB/s.
2. FEATURES 2.1.3Intelligence • • • • • Fan Status Monitoring and Alarm: To prevent system overheat and system damage, the CPU, power supply, and system fans can be monitored for RPM and failure. All the fans are set for its normal RPM range and alarm thresholds. Temperature Monitoring and Alert: To prevent system overheat and system damage, this motherboard supports processor thermal sensing and auto-protection.
2. FEATURES 2.2 CUR-DLSR Motherboard Components See opposite page for locations. Location Processor Support (2) Socket 370 for Pentium III Processors ............................... 2 2. FEATURES MB Components Chipsets ServerWorks ServerSet LE 3.0 North Bridge .......................... 3 ServerWorks Open South Bridge ........................................... 13 4Mbit Flash ROM .................................................................. 18 Super I/O Chipset .......................................
2. FEATURES 2.2.1 Component Locations 1 2 3 4 5 2.
3. HARDWARE SETUP 3.
3. HARDWARE SETUP 3.2 Layout Contents Expansion Slots 1) DIMM 0/1/2/3 2) CPU 3) PCI p.18 168-Pin System Memory Support p.19 Central Processing Unit (CPU) p.20 64-bit PCI Bus Expansion Slot Connectors p.22 PS/2 Mouse Connector (6-pin female) p.22 PS/2 Keyboard Connector (6-pin female) p.23 Universal Serial Bus Ports 0 & 1 (two 4-pin female) p.23 Fast-Ethernet Connector (RJ45) p.23 Parallel Port Connector (25-pin female) p.24 Serial Port COM1 Connector (9-pin male) p.
3. HARDWARE SETUP 3.3 Hardware Setup Procedure Before using your computer, you must complete the following steps: • Check Motherboard Settings • Install Memory Modules • Install the Central Processing Unit (CPU) • Install Expansion Cards • Connect Ribbon Cables, Panel Wires, and Power Supply 3.4 Motherboard Settings 3. H/W SETUP Motherboard Settings WARNING! Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips.
3. HARDWARE SETUP 3.5 System Memory NOTE: No hardware or BIOS setup is required after adding or removing memory. This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are available for 3.3Volt (power level) “registered” Synchronous Dynamic Random Access Memory (SDRAM) of 64, 128, 256, 512, 1024MB with Serial Presence Detect (SPD). ECC memory modules must be used to provide reliability enhancements. Memory speed setup is recommended through the SDRAM Configuration in 4.4.
3. HARDWARE SETUP 3.5.2DIMM Installation Insert the module(s) as shown. Because the number of pins are different on either side of the breaks, the module only fits in the orientation shown. DIMMs are longer and have different pin contacts on each side and therefore have a higher pin density compared to SIMMs. 88 Pins 3. H/W SETUP Motherboard Settings 60 Pins CUR-DLSR CUR-DLSR 168-Pin DIMM Sockets 20 Pins Lock The DIMMs must be 3.3V “registered” for this motherboard.
3. HARDWARE SETUP 3.6 Central Processing Unit (CPU) The motherboard has a PGA 370 socket. WARNING! Be sure that there is sufficient air circulation across the processor heatsink by regularly checking that your CPU fan is working. Without sufficient circulation, the processor could overheat and damage both the processor and the motherboard. The CPU will be unstable if the heatsink is not properly mounted. Double check the contact. 3.
3. HARDWARE SETUP 3.7 Expansion Cards WARNING! Unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 3.7.1Expansion Card Installation Procedure 3. H/W SETUP Motherboard Settings 1. Read the documentation for your expansion card and make any necessary hardware or software settings for your expansion card, such as jumpers. 2.
3. HARDWARE SETUP 3.7.2Assigning IRQs for Expansion Cards This is applicable only when MPS 1.4 Support is Disabled in section 4.6 Boot Menu. Some expansion cards need an IRQ to operate. Generally, an IRQ must be exclusively assigned to one use. In a standard design, there are 16 IRQs available but most of them are already in use, leaving 6 IRQs free for expansion cards. If the motherboard has PCI audio onboard, an additional IRQ will be used.
3. HARDWARE SETUP 3.8 Ports and Connectors WARNING! Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the Motherboard Layout. Placing jumper caps over these connector pins may damage your motherboard. IMPORTANT: Ribbon cables should always be connected with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives.
3. HARDWARE SETUP 3) Universal Serial BUS Ports 0 & 1 (Black two 4-pin USB) Two USB ports are available for connecting USB devices. USB 0 Universal Serial Bus (USB) 1 RJ45 3. H/W SETUP Motherboard Settings 4) Fast-Ethernet Port (RJ-45) The RJ45 connector is optional at the time of purchase and is located on top of the USB connectors. The connector allows the motherboard to connect to a Local Area Network (LAN) through a network hub.
3. HARDWARE SETUP 6) Serial Port (Teal/Turquoise 9-pin COM1) The serial port can be used for pointing devices or other serial devices. See Onboard Serial Port 1 in 4.4.2 I/O Device Configuration for settings. COM1 Serial Ports (9-pin Male) 7) Monitor Output Port (Blue 15-pin VGA) This connector is for output to a VGA-compatible device. 3.
3. HARDWARE SETUP 3. H/W SETUP Motherboard Settings 9) Primary/ Secondary IDE Connectors (40-1 pin IDE1/IDE2) These connectors support the provided IDE ribbon cable. Connect the cable’s blue connector to the motherboard’s primary (recommended) or secondary IDE connector, and then connect the gray connector to the IDE slave device (hard disk drive) and the black connector to the IDE master device. It is recommended that non-UltraDMA/33 devices be connected to the secondary IDE connector.
3. HARDWARE SETUP 10) Wake-On-LAN Connector (3-pin WOL_CON) This connector connects to a LAN card with a Wake-On-LAN output, such as the PCI-L101 Ethernet card (see 7. APPENDIX). The connector powers up the system when a wakeup packet or signal is received through the LAN card. IMPORTANT: This feature requires that Wake On LAN is enabled (see 4.5.1 Power Up Control) and that your system has an ATX power supply with at least 720mA +5V standby power.
3. HARDWARE SETUP 12) IDE/SCSI Activity LED (2-pin IDELED) Also in Panel Connectors This connector supplies power to the cabinet’s activity LED. Read and write activity by devices connected to the Primary/Secondary IDE and SCSI connectors cause the LED to light up. *Same as the “HDD Access LED” in the panel connectors +CUR-DLSR IDELED 3.
3. HARDWARE SETUP 14) SMBus Connector (8-1 pin SMB) This connector allows you to connect SMBus (System Management Bus) devices. SMBus devices communicate by means of the SMBus with an SMBus host and/ or other SMBus devices. SMBus is a specific implementation of an I2C bus, which is a multi-device bus; that is, multiple chips can be connected to the same bus and each one can act as a master by initiating data transfer. CUR-DLSR 3.
3. HARDWARE SETUP 18) ATX Power Switch / Soft-Off Switch Lead (2-pin) The system power is controlled by a momentary switch connected to this lead. Pushing the button once switches the system between ON and SLEEP or ON and SOFT OFF, depending on your BIOS or OS setting. Pushing the switch while in the ON mode for more than 4 seconds turns the system off. The system power LED shows the status of the system power.
3. HARDWARE SETUP 24) ASMC Connectors This motherboard has two ASMC connectors. CUR-DLSR CUR-DLSR ASMC Connectors 3. H/W SETUP Motherboard Settings 25) Serial Port 2 Connector This motherboard has a second serial port connector to accommodate additional serial peripherals. See the BIOS section 4.4.2 I/O Device Configuration to configure Serial Port 2 settings.
3. HARDWARE SETUP 26) Panel 2 Connector This connector supports some of the functions in the 20-pin PANEL connector, such as the power button, IDE LED, and power LED. IDELED ATX Power Button* Power LED +5V PLED PWRBTN# GND IDELEDIDELED+ 1 CUR-DLSR * Requires an ATX power supply. 3. H/W SETUP Motherboard Settings CUR-DLSR Panel 2 Connector 27) Power Button Connector This connector allows you to turn the system ON or OFF. The power LED lights up when the system is turned ON.
3. HARDWARE SETUP (no connection) Chassis Signal Ground 28) Chassis Open Alarm Lead Connector This connector is designed for chassis intrusion detection. When any chassis component is removed, the contact should open and the motherboard will record a chassis intrusion event. The event can be processed by software such as LDCM. 1 34 CHASSIS CUR-DLSR CUR-DLSR Chassis Open Alarm Lead 3.
3. HARDWARE SETUP 30) Two 68-pin Ultra160/Ultra3 SCSI Connectors This motherboard has two 68-Pin Ultra160/Ultra3 SCSI connectors; one for each of the two channels. Each channel can support a maximum of 15 devices as specified by Ultra160/Ultra3 standards. 34 68 1 35 SCSI-A (Internal) 68-Pin Ultra160/Ultra2-Wide SCSI Connector 1 35 SCSI-B (External) 68-Pin Ultra160/ Ultra2-Wide SCSI Connector 3.
3. HARDWARE SETUP SCSI Connection Notes This motherboard has two 68-Pin Ultra160/Ultra3 SCSI connectors; one for each of the two channels. The onboard SCSI chipset incorporates an advanced multimode I/O cell that supports both single-ended (SE), Ultra3, and Ultra160 devices. With Ultra160/Ultra3 devices, the SCSI bus platform performs at full Ultra160/Ultra3 speeds (up to 160MB/sec) and extended cabling 12m (or 25m in a point-to-point configuration).
3. HARDWARE SETUP 3.9 Switches Clear RTC RAM These two solder points allow you to clear the RTC RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS Real Time Clock (RTC) RAM. The RAM data that include system setup information, such as system passwords, is powered by the onboard button cell battery. 3.
3. HARDWARE SETUP 3.10 Starting Up the First Time 1. After you have made all the connections, replace the system unit cover. 2. Be sure that all switches are off (in some systems, marked with ), and the power input voltage is set to comply with the standard used in your country (220V-240V or 110-120V). 3. Connect the power supply cord into the power supply located at the back of your system unit according to the system user’s manual. 4.
3. HARDWARE SETUP 7. During power-on, hold down to enter BIOS setup. Follow the instructions in 4. BIOS SETUP. * Powering Off your computer: You must first exit or shut down your operating system before switching off the power switch. For ATX power supplies, you can press the ATX power switch after exiting or shutting down your operating system.
4. BIOS SETUP 4.1 Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System It is recommended that you save a copy of the original motherboard BIOS along with a Flash Memory Writer utility (AFLASH.EXE) to a bootable floppy disk in case you need to reinstall the BIOS later. AFLASH.EXE is a Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode.
4. BIOS SETUP 5. Select 1. Save Current BIOS to File from the Main menu and press . The Save Current BIOS To File screen appears. Save Current BIOS To File Flash Memory: Winbond W29C020 or SST 29EE020 or Intel 82802AB Current BIOS Version: ASUS XXX-XX ACPI BIOS Revision 100X BIOS Model : XXX-XX BIOS Built Date : 09/25/99 Please Enter File Name to Save: XXX-XX.XXX BIOS Saved Successfully Press ESC To Exit 6. Type a filename and the path, for example, A:\XXX-XX.XXX and then press . 4.1.
4. BIOS SETUP 6. When prompted to confirm the BIOS update, press Y to start the update. Update BIOS Including Boot Block and ESCD Flash Memory: Winbond W29C020 or SST 29EE020 or Intel 82802AB BIOS Version [Current ] ASUS XXX-XX ACPI BIOS Revision 100X [test.awd] ASUS XXX-XX ACPI BIOS Revision 100X BIOS Mode [Current ] [test.awd] XXX-XX XXX-XX Date of BIOS Built [Current ] 09/25/99 [test.awd] 05/29/00 Check sum of 1001.010 is F266. Are you sure (Y/N) ? [Y] Press ESC To Return to Main Menu 7.
4. BIOS SETUP 4.2 BIOS Setup Program This motherboard supports a programmable EEPROM that can be updated using the provided utility as described in 4.1 Managing and Updating Your BIOS. The utility is used if you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section describes how to configure your system using this utility. Even if you are not prompted to use the Setup program, at some time in the future you may want to change the configuration of your computer.
4. BIOS SETUP 4.2.1 BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN ADVANCED POWER BOOT EXIT Use this menu to make changes to the basic system configuration. Use this menu to enable and make changes to the advanced features. Use this menu to configure and enable Power Management features. Use this menu to configure the default system device used to locate and load the Operating System. Use this menu to exit the current menu or specify how to exit the Setup program.
4. BIOS SETUP General Help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing or the + combination. The General Help screen lists the legend keys with their corresponding alternates and functions. Saving Changes and Exiting the Setup Program See 4.7 Exit Menu for detailed information on saving changes and exiting the setup program.
4. BIOS SETUP 4.3 Main Menu When the Setup program is accessed, the following screen appears: Main... System System Legacy Legacy Ê Ê Ê Ê Ê Time: Date: Diskette A: Diskette B: [14:26:36] [08/01/2000] [1.44M.3.5 in.
4. BIOS SETUP 4.3.1 Primary & Secondary Master/Slave Main...
4. BIOS SETUP IMPORTANT: If your hard disk was already formatted on an older previous system, incorrect parameters may be detected. You will need to enter the correct parameters manually or use lowlevel format if you do not need the data stored on the hard disk. If the parameters listed differ from the ones used when the disk was formatted, the disk will not be readable.
4. BIOS SETUP Head This field configures the number of read/write heads. Refer to your drive documentation to determine the correct value to enter into this field. NOTE: To make changes to this field, the Type field must be set to [User Type HDD] and the Translation Method field must be set to [Manual]. Sector This field configures the number of sectors per track. Refer to your drive documentation to determine the correct value to enter into this field.
4. BIOS SETUP Other options for “Type:” are: [CD-ROM] - for IDE CD-ROM drives [LS-120] - for LS-120 compatible floppy disk drives [ZIP-100] - for ZIP-100 compatible disk drives [MO] - for IDE magneto optical disk drives [Other ATAPI Device] - for IDE devices not listed here After using the legend keys to make your selections on this sub-menu, press the key to exit back to the Main menu.
4. BIOS SETUP Language [English] This allows selection of the BIOS’ displayed language. Currently only English is available. Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set the passwords. To set the password, highlight the appropriate field and press . Type in a password and press . You can type up to eight alphanumeric characters. Symbols and other keys are ignored. To confirm the password, type the password again and press the .
4. BIOS SETUP 4.4 Advanced Menu Advanced ...
4. BIOS SETUP PS/2 Mouse Function Control [Auto] The default of [Auto] allows the system to detect a PS/2 mouse on startup. If detected, IRQ12 will be used for the PS/2 mouse. IRQ12 will be reserved for expansion cards only if a PS/2 mouse is not detected. [Enabled] will always reserve IRQ12, whether on startup a PS/2 mouse is detected or not.
4. BIOS SETUP 4.4.2 I/O Device Configuration Advanced ...
4. BIOS SETUP ECP DMA Select [3] This field allows you to configure the parallel port DMA channel for the selected ECP mode. This selection is available only if you select [ECP] or [ECP+EPP] in Parallel Port Mode above. Configuration options: [1] [3] [Disabled] 4.4.3 PCI Configuration Advanced ...
4. BIOS SETUP Onboard SCSI BIOS [Auto] [Auto] allows the motherboard’s BIOS to detect whether you have a Symbios SCSI controller. If the Symbios SCSI controller is detected, the motherboard’s Symbios BIOS will be enabled; if no Symbios SCSI controller is detected, the onboard Symbios SCSI BIOS will be disabled. [Disabled] will disable the motherboard’s Symbios SCSI BIOS so that the BIOS on an add-on Symbios SCSI card can be used.
4. BIOS SETUP 4.4.4 Shadow Configuration Advanced ...
4. BIOS SETUP 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity. Power ...
4. BIOS SETUP Video Off Option [Suspend > Off ] This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend > Off] Video Off Method [DPMS OFF] This field defines the video off features. The DPMS (Display Power Management System) feature allows the BIOS to control the video display card if it supports the DPMS feature. [Blank Screen] only blanks the screen (use this for monitors without power management or “green” features.
4. BIOS SETUP 4.5.1 Power Up Control Power ... Power Up Control AC PWR Loss Restart PWR Up On Modem Act Wake On LAN [Disabled] [Enablded] [Disabled] Automatic Power Up [Disabled] F1 Help ESC Exit ↑↓ ←→ Select Item Select Menu -/+ Change Values Enter Select Ê Submenu Item Specific Help F5 Setup Defaults F10 Save and Exit AC PWR Loss Restart [Disabled] This allows you to set whether you want your system to reboot after the power has been interrupted.
4. BIOS SETUP Automatic Power Up [Disabled] This allows an unattended or automatic system power up. You may configure your system to power up at a certain time of the day by selecting [Everyday] or at a certain time and day by selecting [By Date]. NOTE: Automatic Power Up will not work if the system is powered down by operating systems, such as Windows 98, which have ACPI support enabled.
4. BIOS SETUP 4.5.2 Hardware Monitor Power ...
4. BIOS SETUP 4.6 Boot Menu Boot ... Item Specific Help 1. 2. 3. 4. Removable Device IDE Hard Drive ATAPI CD-ROM Other Boot device [Legacy Floppy] [None] [CD-S500/A] [INT18 Device (Networ] Plug & Play O/S MPS 1.4 Support Boot Virus Detection Quick Power On Self Test Boot Up Floppy Seek [No] [Enabled] [Enabled] [Enabled] [Enabled] F1 Info ... Boot Sequence The Boot menu allows you to select among the four possible types of boot devices listed using the up and down arrow keys.
4. BIOS SETUP Plug & Play O/S [No] This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. When [Yes] is selected, interrupts may be reassigned by the OS. When a non-PnP OS is installed or you want to prevent reassigning of interrupt settings, select the default setting of [No]. Configuration options: [No] [Yes] MPS 1.4 Support [Enabled] This field allows you to enable or disable the MultiProcessor Specification 1.4 support.
4. BIOS SETUP 4.7 Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: NOTE: Pressing does not exit this menu. You must select one of the options from this menu or from the legend bar to exit this menu.
4. BIOS SETUP Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When this option is selected or if is pressed, a confirmation is requested. Select [Yes] to load default values. You can now select Exit Saving Changes or make other changes before saving the values to the non-volatile RAM. Discard Changes This option allows you to discard the selections you made and restore the values you previously saved.
