® CUC2000 JumperFree™ Camino Motherboard USER’S MANUAL
USER'S NOTICE No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS CONTACT INFORMATION ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Address: Telephone: Fax: Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support MB/Others (Tel): +886-2-2890-7121 (English) Notebook (Tel): +886-2-2890-7122 (English) Desktop/Server (Tel):+886-2-2890-7123 (English) Fax: +886-2-2895-9254 Email: tsd@asus.com.tw WWW: www.asus.com.tw FTP: ftp.asus.com.
CONTENTS 1. INTRODUCTION ............................................................................. 7 1.1 How This Manual Is Organized .................................................. 7 1.2 Item Checklist ............................................................................. 7 2. FEATURES ........................................................................................ 8 2.1 The ASUS CUC2000 .................................................................. 8 2.1.1 Specifications ........
CONTENTS 4.4 Advanced Menu ........................................................................ 58 4.4.1 Chip Configuration ........................................................ 62 4.4.2 I/O Device Configuration .............................................. 64 4.4.3 PCI Configuration ......................................................... 66 4.4.4 Shadow Configuration ..................................................... 69 4.5 Power Menu ...........................................................
FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
1. INTRODUCTION 1. INTRODUCTION Manual / Checklist 1.1 How This Manual Is Organized This manual is divided into the following sections: 1. 2. 3. 4. 5. 6. 7. INTRODUCTION FEATURES HARDWARE SETUP BIOS SETUP SOFTWARE SETUP SOFTWARE REFERENCE APPENDIX Manual information and checklist Production information and specifications Intructions on setting up the motherboard.
2. FEATURES 2.1 The ASUS CUC2000 The ASUS CUC2000 motherboard is carefully designed for the demanding PC user who wants advanced features processed by the fastest processors. 2.1.1 Specifications • 2.
2. FEATURES • • • • • • • • PC Health Monitoring: Provides an easy way to examine and manage system status information, such as CPU and systerm voltages, temperatures, and fan status through the onboard hardware ASUS ASIC and the bundled ASUS PC Probe or Intel LDCM software. AMR Slot: Audio Modem Riser slot supports a very affordable audio and/or modem riser card. PCI/ISA Expansion Slots: Provides five 32-bit PCI (PCI 2.2 compliant) with one optional 16-bit ISA expansion slot.
2. FEATURES 2.1.3 Performance • • • 2. FEATURES Performance • • • • • 10 UltraPerformance: Onboard IDE Bus Master controller with two connectors that support four IDE devices in two channels. Supports UltraDMA/66, UltraDMA/33 (IDE DMA Mode 2), PIO Modes 3 & 4, and supports Enhanced IDE devices, such as DVD-ROM, CD-ROM, CD-R/RW, LS-120, and Tape Backup drives. Dual Speeds: CPU frequency can operate at either 133MHz or 100MHz.
2. FEATURES 2.1.4 Intelligence • • • • • • • Fan Status Monitoring and Alarm: To prevent system overheat and system damage, the CPU, power supply, and system fans can be monitored for RPM and failure. All the fans are set for its normal RPM range and alarm thresholds. Temperature Monitoring and Alert: To prevent system overheat and system damage, this motherboard supports processor thermal sensing and auto-protection.
2. FEATURES 2.2 CUC2000 Motherboard Components See opposite page for locations. Location Processor Support Socket 370 for Pentium III/Celeron Processors ....................... 3 Feature Setting DIP Switches ................................................. 14 2. FEATURES MB Components Chipsets Intel 820 Memory Controller Hub (MCH) ............................... 2 Intel 82805 Memory Translator Hub (MTH) ........................... 4 Intel I/O Controller Hub (ICH) .........................................
2. FEATURES 2.2.1 Component Locations 1 2 3 4 5 6 7 2.
3. HARDWARE SETUP 3.1 CUC2000 Motherboard Layout 21.8 cm (8.
3. HARDWARE SETUP 3.2 Layout Contents Motherboard Settings 1) JEN p.18 JumperFree™ Mode (Enable/Disable) 2) USBPWR p.19 USB Device Wake Up (Enable/Disable) 3) SAFE_MODE p.19 Safe Mode Setting (Normal/Safe Mode) 4) NO_REBOOT p.20 Automatic Timeout Reboot Setting (Normal/No Reboot) 5) AUD_EN1, AUD_EN2 p.20 Onboard Audio CODEC Setting (Enable/Disable) 6) JP5 p.21 Voltage I/O Setting (Enable/Disable) 7) JP6/JP3 p.21 MCH/MTH Voltage Setting (Enable/Disable) 8) SW2 p.
3. HARDWARE SETUP 16) IR p.38 Serial and Consumer Infrared Module Connector (10-pin) 17) USB2, USB3 p.39 USB Headers 18) MIC2 p.39 Internal Microphone Connector (3-pin MIC2) 19) SMB p.40 SMBus Connector (5-1 pins) 20) PWR.LED (PANEL) p.41 System Power LED Lead (3-1 pins) 21) KEYLOCK (PANEL) p.41 Keyboard Lock Switch Lead (2 pins) 22) SPEAKER (PANEL) p.41 System Warning Speaker Connector (4 pins) 23) MSG.LED (PANEL) p.41 System Message LED (2 pins) 24) SMI (PANEL) p.
3. HARDWARE SETUP 3.3 Hardware Setup Procedure Before using your computer, you must complete the following steps: • Check Motherboard Settings • Install Memory Modules • Install the Central Processing Unit (CPU) • Install Expansion Cards • Connect Ribbon Cables, Panel Wires, and Power Supply 3.4 Motherboard Settings 3. H/W SETUP Motherboard Settings WARNING! Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips.
3. HARDWARE SETUP Motherboard Feature Settings The motherboard’s onboard functions are either adjusted through jumpers or DIP switches. When using DIP switches, the white block represents the switch’s position. The example below shows all the switches in the OFF position. 1. Frequency Selection 2. Frequency Selection 3. Frequency Selection 4. Frequency Selection 5. Frequency Selection. CUC2000 ® 3.
3. HARDWARE SETUP 2) USB Device Wake Up (USBPWR) This allows you to disable or enable the USB device power up function. Set this jumper to Enable if you wish to use your USB device to wake up your computer. This feature requires an ATX power supply that can supply at least 2A on the +5VSB lead. The default is set to Disable because not all computers have the appropriate ATX power supply. Your computer will not power ON if you set this to Enable and do not have the appropriate ATX power supply.
3. HARDWARE SETUP 4) Automatic Timeout Reboot Setting (NO_REBOOT) The motherboard is set so that when the BIOS detects a hang (timeout) during bootup, the motherboard will automatically reboot. If rebooting is repeating ineffectively, set this jumper to No Reboot to disable auto-reboot. However, if Safe Mode Setting (SAFE_MODE) is set to Safe Mode, setting Automatic Timeout Reboot Setting (NO_REBOOT) to No Reboot will bring the system to Safe Mode so you may be able to correct any problems.
3. HARDWARE SETUP 6) Voltage I/O Setting (JP5) This jumper allows you to select the voltage supplied to the DRAM, chipset, AGP, and PCI. The default setting of Normal should be used unless processor overclocking requires a higher voltage (Test). Setting JP5 Normal [1-2] (default) Test [2-3] JP5 1 2 Normal (Default) 2 3 Test CUC2000 3.
3. HARDWARE SETUP 8) CPU External Frequency Setting (SW2) This option tells the clock generator what frequency to send to the CPU and the PCI bus. This allows the selection of the CPU’s External frequency. IMPORTANT: 1. In JumperFree mode, all dip switches must be set to OFF. 2. When JumperFree mode is enabled, use BIOS setup in place of these switches (see CPU Speed in Advanced Menu in BIOS Setup). NOTE: Only selected switches are illustrated. For a complete frequency listing, see next page. SW2 3.
3. HARDWARE SETUP External Frequency Table The following table is for use by experienced motherboard installers only. Overclocking can result in system instability or even shortening the life of the processor.
3. HARDWARE SETUP 3.5 System Memory (DIMM) NOTE: No hardware or BIOS setup is required after adding or removing memory. This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Access Memory (SDRAM) of 64, 128, 256, or 512MB with Serial Presence Detect (SPD). This chipset does not support ECC. However, ECC memory modules may still be used, but the ECC function will not be available.
3.
3. HARDWARE SETUP 3.5.2 DIMM Installation Insert the module(s) as shown. Because the number of pins are different on either side of the breaks, the module will only fit in the orientation shown. DIMMs are longer and have different pin contact on each side and therefore have a higher pin density. SIMMs have the same pin contact on both sides. Lock 20 Pins 60 Pins CUC2000 ® 88 Pins 3. H/W SETUP System Memory CUC2000 168-Pin DIMM Sockets The DIMMs must be 3.3V Unbuffered for this motherboard.
3. HARDWARE SETUP 3.6 Central Processing Unit (CPU) The motherboard provides a ZIF Socket 370. The CPU that came with the motherboard should have a fan attached to it to prevent overheating. If this is not the case, then purchase a fan before you turn on your system. WARNING! Be sure that there is sufficient air circulation across the processor’s heatsink by regularly checking that your CPU fan is working.
3. HARDWARE SETUP 3.7 Expansion Cards WARNING! Unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 3.7.1 Expansion Card Installation Procedure 3. H/W SETUP Expansion Cards 1. Read the documentation for your expansion card and make any necessary hardware or software settings for your expansion card, such as jumpers. 2.
3. HARDWARE SETUP 3.7.2 Assigning IRQs for Expansion Cards Some expansion cards need an IRQ to operate. Generally, an IRQ must be exclusively assigned to one use. In a standard design, there are 16 IRQs available but most of them are already in use, leaving 6 IRQs free for expansion cards. If your motherboard has PCI audio onboard, an additional IRQ will be used. If your motherboard also has MIDI enabled, another IRQ will be used, leaving 4 IRQs free.
3. HARDWARE SETUP 3. H/W SETUP DMA Channels Both ISA and PCI expansion cards may require IRQs. System IRQs are available to cards installed in the ISA expansion bus first, then any remaining IRQs are available to PCI cards. Currently, there are two types of ISA cards. The original ISA expansion card design, now referred to as legacy ISA cards, requires that you configure the card’s jumpers manually and then install it in any available slot on the ISA bus.
3. HARDWARE SETUP 3.7.3 Accelerated Graphics Port (AGP) This motherboard provides an accelerated graphics port (AGP) pro slot to support a new generation of AGP graphics cards with ultra-high memory bandwidth. AGP Card without Retention Notch CUC2000 ® TOP VIEW 20-pin bay Rib (inside slot) 28-pin bay Rib CUC2000 Accelerated Graphics Port (AGP) 3. H/W SETUP Connectors CAUTION! The AGP Pro slot is shipped with a warning label over the 20-pin bay.
3. HARDWARE SETUP 3.8 Connectors WARNING! Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the Motherboard Layout. Placing jumper caps over these connector pins will cause damage to your motherboard. IMPORTANT: Ribbon cables should always be connected with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives.
3. HARDWARE SETUP 3) Universal Serial BUS Ports 0 & 1 (Black two 4-pin USB) Two USB ports are available for connecting USB devices. USB 1 Universal Serial Bus (USB) 2 3. H/W SETUP Connectors 4) Parallel Port Connector (Burgundy 25-pin PRINTER) You can enable the parallel port and choose the IRQ through Onboard Parallel Port (see 4.4.2 I/O Device Configuration). NOTE: Serial printers must be connected to the serial port.
3. HARDWARE SETUP 6) Game/MIDI Connector (Gold 15-pin GAME_AUDIO) (optional) You may connect game joysticks or game pads to this connector for playing games. Connect MIDI devices for playing or editing professional audio. 3. H/W SETUP Connectors 7) Audio Port Connectors (Three 1/8” GAME_AUDIO) (optional) Line Out (lime) can be connected to headphones or preferably powered speakers.
3. HARDWARE SETUP 3. H/W SETUP Connectors 9) Primary (Blue) / Secondary IDE Connectors (40-1 pin IDE1/IDE2) These connectors support the provided UltraDMA/66 IDE hard disk ribbon cable. Connect the cable’s blue connector to the motherboard’s primary (recommended) or secondary IDE connector, and then connect the gray connector to your UltraDMA/66 slave device (hard disk drive) and the black connector to your UltraDMA/66 master device.
3. HARDWARE SETUP 11) Wake-On-LAN Connector (3-pin WOL_CON) This connector connects to a LAN card with a Wake-On-LAN output, such as the ASUS PCI-L101 Ethernet card (see 7. APPENDIX). The connector powers up the system when a wakeup packet or signal is received through the LAN card. IMPORTANT: This feature requires that Wake-On-LAN features are enabled (see 4.5.1 Power Up Control) and that your system has an ATX power supply with at least 720mA +5V standby power.
3. HARDWARE SETUP 13) IDE Activity LED (2-pin IDELED) This connector supplies power to the cabinet’s IDE activity LED. Read and write activity by devices connected to the Primary or Secondary IDE connectors will cause the LED to light up. TIP: If the case-mounted LED does not light, try reversing the 2-pin plug. CUC2000 ® IDELED CUC2000 IDE Activity LED 3.
3. HARDWARE SETUP 15) Internal Audio Connectors (4-pin CD_IN, AUX, VIDEO, MODEM) These connectors allow you to receive stereo audio input from such sound sources as a CD-ROM, TV tuner, or MPEG card. The MODEM connector allows the onboard audio to interface with a voice modem card with a similar connector. It also allows the sharing of mono_in (such as a phone) and mono_out (such as a speaker) between the onboard audio and a voice modem card.
3. HARDWARE SETUP CUC2000 USBP4USBP4+ GND USB Power 17) USB Headers (10-1 pin USB2, 5-1 pin USB3) If the USB port connectors on the back panel are inadequate, two USB headers are available for three additional USB port connectors. Connect the USB headers to an optional 3-port USB connector set and mount the bracket to an open slot on your chassis. 1 ® USB3 6 USB2 10 1: USB Power 2: USBP2– 3: USBP2+ 4: GND 5: NC 6: USB Power 7: USBP3– 8: USBP3+ 9: GND 3.
3. HARDWARE SETUP CUC2000 Ground SMBDATA +5V SMBCLK 19) SMBus Connector (5-1 pin SMB) This connector allows you to connect SMBus (System Management Bus) devices. SMBus devices communicate by means of the SMBus with an SMBus host and/or other SMBus devices. SMBus is a specific implementation of an I2C bus, which is a multi-device bus; that is, multiple chips can be connected to the same bus and each one can act as a master by initiating data transfer. ® 1 SMB 3.
3. HARDWARE SETUP 20) System Power LED Lead (3-1 pin PWR.LED) This 3-1 pin connector connects to the system power LED, which lights when the system is powered on and blinks when it is in sleep or soft-off mode. 21) Keyboard Lock Switch Lead (2-pin KEYLOCK) This 2-pin connector connects to the case-mounted key switch to allow keyboard locking. NOTE: When the keyboard is locked, the mouse can still be used.
3. HARDWARE SETUP 27) ATX Power Supply Connector (20-pin block ATXPWR) This connector connects to an ATX power supply. The plug from the power supply will only insert in one orientation because of the different hole sizes. Find the proper orientation and push down firmly making sure that the pins are aligned. IMPORTANT: Make sure that your ATX power supply can supply at least 10mA on the +5-volt standby lead (+5VSB).
3. HARDWARE SETUP 3.9 Starting Up the First Time 1. After all connections are made, close the system case cover. 2. Be sure that all switches are off (in some systems, marked with ). 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Connect the power cord into a power outlet that is equipped with a surge protector. 5. You may then turn on your devices in the following order: a. Your monitor b.
3. HARDWARE SETUP 7. During power-on, hold down to enter BIOS setup. Follow the instructions in 4. BIOS SETUP. * Powering Off your computer: You must first exit or shut down your operating system before switching off the power switch. For ATX power supplies, you can press the ATX power switch after exiting or shutting down your operating system.
4. BIOS SETUP 4.1 Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System It is recommended that you save a copy of the original motherboard BIOS along with a Flash Memory Writer utility (AFLASH.EXE) to a bootable floppy disk in case you need to reinstall the BIOS later. AFLASH.EXE is a Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode.
4. BIOS SETUP 5. Select 1. Save Current BIOS to File from the Main menu and press . The Save Current BIOS To File screen appears. 6. Type a filename and the path, for example, A:\XXX-XX.XXX and then press . 4.1.2 Updating BIOS Procedures WARNING! Only update your BIOS if you have problems with your motherboard and you know that the new BIOS revision will solve your problems. Careless updating can result in your motherboard having more problems! 4. BIOS SETUP Updating BIOS 1.
4. BIOS SETUP 6. When prompted to confirm the BIOS update, press Y to start the update. 4. BIOS SETUP Updating BIOS 7. The utility starts to program the new BIOS information into the flash ROM. The boot block will be updated automatically only when necessary. This will minimize the chance that a failed update will prevent your system from booting up. When the programming is finished, Flashed Successfully will be displayed. 8. Follow the onscreen instructions to continue.
4. BIOS SETUP (This page was intentionally left blank.) 4.
4. BIOS SETUP 4.2 BIOS Setup Program This motherboard supports a programmable EEPROM that can be updated using the provided utility as described in 4.1 Managing and Updating Your BIOS. The utility is used if you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section describes how to configure your system using this utility. Even if you are not prompted to use the Setup program, at some time in the future you may want to change the configuration of your computer.
4. BIOS SETUP 4.2.1 BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADVANCED Use this menu to enable and make changes to the advanced features. POWER Use this menu to configure and enable Power Management features. BOOT Use this menu to configure the default system device used to locate and load the Operating System. EXIT Use this menu to exit the current menu or specify how to exit the Setup program.
4. BIOS SETUP General Help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing or the + combination. The General Help screen lists the legend keys with their corresponding alternates and functions. Saving Changes and Exiting the Setup Program See 4.7 Exit Menu for detailed information on saving changes and exiting the setup program.
4. BIOS SETUP 4.3 Main Menu When the Setup program is accessed, the following screen appears: 4. BIOS SETUP Main Menu System Time [XX:XX:XX] Sets your system to the time that you specify (usually the current time). The format is hour, minute, second. Valid values for hour, minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the or + keys to move between the hour, minute, and second fields.
4. BIOS SETUP 4.3.1 Primary & Secondary Master/Slave 4. BIOS SETUP Master/Slave Drives NOTE: Before attempting to configure a hard disk drive, make sure you have the configuration information supplied by the manufacturer of the drive. Incorrect settings may cause your system to not recognize the installed hard disk. To allow the BIOS to detect the drive type automatically, select [Auto]. Type [Auto] Select [Auto] to automatically detect an IDE hard disk drive.
4. BIOS SETUP IMPORTANT: If your hard disk was already formatted on an older previous system, incorrect parameters may be detected. You will need to enter the correct parameters manually or use low-level format if you do not need the data stored on the hard disk. If the parameters listed differ from the ones used when the disk was formatted, the disk will not be readable.
4. BIOS SETUP ASUS CUC2000 User’s Manual 4. BIOS SETUP Master/Slave Drives Head This field configures the number of read/write heads. Refer to your drive documentation to determine the correct value to enter into this field. NOTE: To make changes to this field, the Type field must be set to [User Type HDD] and the Translation Method field must be set to [Manual]. Sector This field configures the number of sectors per track.
4. BIOS SETUP Other options for “Type:” are: [CD-ROM] - for IDE CD-ROM drives [LS-120] - for LS-120 compatible floppy disk drives [ZIP-100] - for ZIP-100 compatible disk drives [MO] - for IDE magneto optical disk drives [Other ATAPI Device] - for IDE devices not listed here After using the legend keys to make your selections on this sub-menu, press the key to exit back to the Main menu.
4. BIOS SETUP 4. BIOS SETUP Main Menu Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set the passwords. To set the password, highlight the appropriate field and press . Type in a password and press . You can type up to eight alphanumeric characters. Symbols and other keys are ignored. To confirm the password, type the password again and press the . The password is now set to [Enabled]. This password allows full access to the BIOS Setup menus.
4. BIOS SETUP 4.4 Advanced Menu 4. BIOS SETUP Advanced Menu CPU Internal Frequency [Manual] When the motherboard is set to JumperFree™ mode, this field allows you to select the internal frequency of your CPU. Available options include multiples of 100 and 133. Select [Manual] if you want to make changes to the subsequent 2 fields. Note that selecting a frequency higher than the CPU manufacturer recommends may cause the system to hang or crash. See System Hangup on page 67.
4. BIOS SETUP CPU Vcore This field displays the core voltage supplied to the CPU. If you want to set it manually, always refer to the CPU documentation. The pictures shown here provide only examples of possible Vcore ranges. Using Celeron processors Using Pentium III processors SDRAM Frequency (MHz) [Auto] This feature tells the clock generator what frequency to send to the SDRAM. The default setting [Auto] seeks to balance optimal performance with stability.
4. BIOS SETUP USB Legacy Support [Auto] This motherboard supports Universal Serial Bus (USB) devices. The default of [Auto] allows the system to detect a USB device on startup. If detected, USB controller legacy mode will be enabled. If not detected, USB controller legacy mode will be disabled. When this field is set to [Disabled], USB controller legacy mode is disabled no matter whether you are using a USB device or not.
4. BIOS SETUP For processors with unlocked frequency multiplier 4. BIOS SETUP JumperFree Mode System Hangup If your system crashes or hangs due to improper frequency settings, power OFF your system and restart. The system will start up in safe mode running at a bus speed of 100MHz and enter BIOS setup.
4. BIOS SETUP 4.4.1 Chip Configuration 4. BIOS SETUP Chip Configuration SDRAM Configuration [By SPD] This sets the optimal timings for items 2–4, depending on the memory modules that you are using. Default setting is [By SPD], which configures items 2–4 by reading the contents in the SPD (Serial Presence Detect) device. The EEPROM on the memory module stores critical parameter information about the module, such as memory type, size, speed, voltage interface, and module banks.
4. BIOS SETUP SDRAM MA Wait State [Normal] This controls the leadoff clocks for CPU read cycles. Leave on default setting. Configuration options: [Fast] [Normal] Graphics Window Size [64MB] This feature allows you to select the size of mapped memory for AGP graphic data. Configuration options: [4MB] [8MB] [16MB] [32MB] [64MB] [128MB] [256MB] Video Memory Cache Mode [UC] USWC (uncacheable, speculative write combining) is a new cache technology for the video memory of the processor.
4. BIOS SETUP 4.4.2 I/O Device Configuration (scroll down to see more items, as shown here) 4. BIOS SETUP I/O Device Config Onboard AC97 Modem Controller, Audio Controller [Auto] [Auto] allows the motherboard’s BIOS to detect whether you are using any modem/ audio device. If a modem/audio device is detected, the onboard modem/audio controller will be enabled; if no modem/audio device is detected, the onboard modem/ audio controller will be disabled.
4. BIOS SETUP UART2 Use Standard Infrared [Disabled] When enabled, this field activates the onboard standard infrared feature and sets the second serial UART to support the infrared module connector on the motherboard. If your system already has a second serial port connected to the onboard COM2 connector, it will no longer work if you enable the infrared feature. See IrDA-Compliant Infrared Module Connector in 3.8 External Connectors.
4. BIOS SETUP 4.4.3 PCI Configuration Slot 1, Slot 2, Slot 3/5, Slot 4 IRQ [Auto] These fields set how IRQ use is determined for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ use. Configuration options: [Auto] [NA] [3] [4] [5] [7] [9] [10] [11] [12] [14] [15] 4. BIOS SETUP PCI Configuration PCI/VGA Palette Snoop [Disabled] Some nonstandard VGA cards, such as graphics accelerators or MPEG video cards, may not show colors properly.
4. BIOS SETUP USB Function [Enabled] This motherboard supports Universal Serial Bus (USB) devices. Set to [Enabled] if you want to use USB devices. Configuration options: [Disabled] [Enabled] VGA BIOS Sequence [PCI/AGP] If your computer has both PCI and AGP VGA cards, this field allows you to select which of the cards will act as your primary graphics card. [AGP/PCI] uses the AGP card as your primary card. The default, [PCI/AGP], allows your PCI graphics card to take precedence when detected.
4. BIOS SETUP PCI/PNP ISA DMA Resource Exclusion 4. BIOS SETUP PCI Configuration DMA x Used By ISA [No/ICU] These fields indicate whether or not the displayed DMA channel for each field is being used by a legacy (non-PnP) ISA card. The default setting indicates either that the displayed DMA channel is not used or an ICU is being used to determine if an ISA card is using that channel.
4. BIOS SETUP ISA MEM Block BASE [No/ICU] This field allows you to set the base address and block size of a legacy ISA card that uses any memory segment within the C800 and DFFF address range. If you have such a card and you are not using an ICU to specify its address range, select a base address from the six available options; the ISA MEM Block SIZE field will then appear for selecting the block size.
4. BIOS SETUP 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity. 4. BIOS SETUP Power Menu Power Management [User Define] This option must be enabled to use any of the automatic power saving features. If this menu item is set to [Disabled], power management features will not function regardless of other field settings on this menu.
4. BIOS SETUP Video Off Option [Suspend -> Off ] This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off] Video Off Method [DPMS OFF] This field defines the video off features. The DPMS (Display Power Management System) feature allows the BIOS to control the video display card if it supports the DPMS feature. [Blank Screen] only blanks the screen (use this for monitors without power management or “green” features.
4. BIOS SETUP 4.5.1 Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether you want your system to reboot after the power has been interrupted. [Disabled] leaves your system off and [Enabled] reboots your system. [Previous State] sets your system back to the state it is before the power interruption. Configuration options: [Disabled] [Enabled] [Previous State] 4.
4. BIOS SETUP Wake On PS2 KB/PS2 Mouse [Disabled] Set this field to [Enabled] if you wish to use your PS2 keyboard, PS2 mouse, or Consumer IR device to power up your computer. This feature requires an ATX power supply that can supply at least 300mA on the +5VSB lead. The default is set to [Disabled] because not all computers have the appropriate ATX power supply. Your computer will not power ON if you set this to [Enabled] and do not have the appropriate ATX power supply.
4. BIOS SETUP 4.5.2 Hardware Monitor MB Temperature, CPU Temperature [xxxC/xxxF] The onboard hardware monitor is able to detect the MB (motherboard) and CPU temperatures. Set to [Ignore] only if necessary. 4. BIOS SETUP Hardware Monitor CPU Fan, Power Fan, Chassis Fan Speed [xxxxRPM] The onboard hardware monitor is able to detect the CPU fan speed, power supply fan speed, and the chassis fan speed in rotations per minute (RPM). The presence of the fans is automatically detected.
4. BIOS SETUP 4.6 Boot Menu Boot Sequence 4. BIOS SETUP Hardware Monitor The Boot menu allows you to select among the four possible types of boot devices listed using the up and down arrow keys. By using the <+> or key, you can promote devices and by using the <-> key, you can demote devices. Promotion or demotion of devices alters the priority which the system uses to search for a boot device on system power up.
4. BIOS SETUP Plug & Play O/S [No] This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. When [Yes] is selected, interrupts may be reassigned by the OS. When a non-PnP OS is installed or you want to prevent reassigning of interrupt settings, select the default setting of [No]. Configuration options: [No] [Yes] Boot Virus Detection [Enabled] This field allows you to set boot virus detection, ensuring a virus-free boot sector.
4. BIOS SETUP 4.7 Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: 4. BIOS SETUP Exit Menu NOTE: Pressing does not exit this menu. You must select one of the options from this menu or from the legend bar to exit this menu.
4. BIOS SETUP Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When this option is selected or if is pressed, a confirmation is requested. Select [Yes] to load default values. You can now select Exit Saving Changes or make other changes before saving the values to the non-volatile RAM. Discard Changes This option allows you to discard the selections you made and restore the values you previously saved.
5. SOFTWARE SETUP 5.1 Operating Systems You should always use the latest operating system and updates when using new hardware to ensure full compliancy. You may use any version of Windows 98, but for Windows 95, you must use OSR 2.0 or later. For Windows NT 4.0, you must use Service Pack 3.0 or later. 5.1.1 Windows 98 First Time Installation 5. S/W S/W SETUP SETUP 5.
5. SOFTWARE SETUP 5.2 CUC Series Motherboard Support CD NOTE: The support CD contents are subject to change at any time without notice. To begin using your support CD disc, just insert it into your CD-ROM drive and the support CD installation menu should appear. If the menu does not appear, doubleclick or run E:\ASSETUP.EXE (assuming that your CD-ROM drive is drive E:). 5.2.1 Installation Menu • • • • 5.
5. SOFTWARE SETUP (TO SEE THE FOLLOWING ITEMS, CLICK RIGHT ARROW ON THE LOWERRIGHT CORNER OF THE MAIN MENU) • Install Adobe Acrobat Reader Vx.x: Installs the Adobe Acrobat Reader software necessary to view user’s manuals saved in PDF format. Updated or other language versions of this motherboard's manual is available in PDF format at any of our web sites. • Show Motherboard Information: Allows you to view information about your motherboard, such as product name, BIOS version, and CPU.
5. SOFTWARE SETUP 5.3 Intel LDCM Administrator Setup System Requirements • • • • • • • • Intel® Pentium® microprocessor or higher. Operating system: Microsoft Windows 95 (can be OEM Service Release 2), or Windows 98, or Windows NT 4.0 (Service Pack 4 or later). Microsoft Internet Explorer 4.01 or higher. Memory: 16 MB of RAM for Windows 95/98; 24 MB of RAM for Windows NT (32 MB recommended).
5. SOFTWARE SETUP (6) Click here. (5) Click here. (7) Click here. (8) Enter username and password, and other options, and then click here. (9) Click here. (10) Click here. 5. S/W SETUP Windows 98 NOTE: This warning appears only if you don’t have the Acrobat Reader installed. See 5.11 Install Adobe AcroBat Reader Vx.x on how to install the Acrobar Reader.
5. SOFTWARE SETUP 5.4 Intel LDCM Client Setup System Requirements • • • • • • • • Intel® Pentium® microprocessor or higher. Operating system: Microsoft Windows 95 (can be OEM Service Release 2), or Windows 98, or Windows NT 4.0 (Service Pack 4 or later). Microsoft Internet Explorer 4.01 or higher. Memory: 16 MB of RAM for Windows 95/98; 24 MB of RAM for Windows NT (32 MB recommended).
5. SOFTWARE SETUP (5) Click here. (6) Click here. (7) Click here. (8) Click here. (9) Click here. 5. S/W SETUP Windows 98 (10) Click here. NOTE: This warning appears only if you don’t have the Acrobat Reader installed. See 5.11 Install Adobe AcroBat Reader Vx.x on how to install the Acrobar Reader. (11) Click here.
5. SOFTWARE SETUP 5.5 INF Update Utility for Intel 820 Chipset Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (1) Click here. (2) Click here. (3) Click here. (4) Click here. 5. S/W SETUP Windows 98 (5) Click here.
5. SOFTWARE SETUP 5.6 Install Audio Driver Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (2) Click here. (1) Click here. (3) Click here and then click Finish to restart* your computer. 5. S/W SETUP Windows 98 * You may choose to restart your computer later when this option is offered, especially if you still want to install other drivers and/or software.
5. SOFTWARE SETUP 5.7 Install ASUS PC Probe Vx.xx Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. NOTE: ASUS PC Probe will not run if another hardware monitoring utility is installed. To uninstall any program, see 5.12 Uninstalling Programs. (2) Click here. (1) Click here. (4) Click here. (3) Click here. 5. S/W SETUP Windows 98 (5) Click here. (7) Click here. 88 (6) Click here.
5. SOFTWARE SETUP 5.8 Install ASUS Update Vx.xx Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (2) Click here. (1) Click here. (4) Click here. 5. S/W SETUP Windows 98 (3) Click here. (5) Click here.
5. SOFTWARE SETUP 5.9 Install PC-Cillin 98 Vx.xx Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (1) Click here. (2) Click here. (3) Click here only after you have read the License Agreement. (4) Setup will proceed with the installation if no viruses are found. Click here to start installation. (6) & (7) Select the preferred features by clicking the appropriate buttons. (5) Click here. 5.
5. SOFTWARE SETUP 5.10 Install YAMAHA S-YXG50 SoftSynthesizer Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (1) Click here. (2) Click here. (5) Click here. (4) Click here. 5. S/W SETUP Windows 98 (3) Enter the information requested and click here. (6) Click here. (7) Click here.
5. SOFTWARE SETUP 5.11 Install Adobe Acrobat Reader Vx.x Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (1) Click here. (2) Click here. (3) Click here only after you have read the License Agreement. 5. S/W SETUP Windows 98 (5) Click here and then click Finish to restart. 92 ASUS CUC2000 User’s Manual (4) Click here.
5. SOFTWARE SETUP 5.12 Uninstalling Programs Add/Remove Programs is a basic component within Windows. You may use this function if a program does not provide its own uninstallation program. (1) Double-click here to open the Add/Remove Programs Properties dialog box. 5. S/W SETUP Windows 98 (2) Select the program to remove and click Add/ Remove. (3) Click here.
5. SOFTWARE SETUP (This page was intentionally left blank.) 5.
6. S/W REFERENCE ASUS PC Probe 6. SOFTWARE REFERENCE 6.1 ASUS PC Probe ASUS PC Probe is a convenient utility to continuously monitor your computer system’s vital components, such as fan rotations, voltages, and temperatures. It also has a utility that lets you review useful information about your computer, such as hard disk space, memory usage, and CPU type, CPU speed, and internal/external frequencies through the DMI Explorer. 6.1.
6. SOFTWARE REFERENCE 6. S/W REFERENCE ASUS PC Probe 6.1.2 Using ASUS PC Probe Monitoring Monitor Summary Shows a summary of the items being monitored. Temperature Monitor Shows the PC’s temperature (for supported processors only). Temperature Warning threshold adjustment (Move the slider up to increase the threshold level or down to decrease the threshold level) Fan Monitor Shows the PC’s fan rotation.
6. S/W REFERENCE ASUS PC Probe 6. SOFTWARE REFERENCE Settings Lets you set threshold levels and polling intervals or refresh times of the PC’s temperature, fan rotation, and voltages. CPU Cooling System Setup Lets you select when to enable software CPU cooling. When When CPU Overheated is selected, the CPU cooling system is enabled whenever the CPU temperature reaches the threshold value. History Lets you record the monitoring activity of a certain component of your PC for future reference.
6. SOFTWARE REFERENCE 6. S/W REFERENCE ASUS PC Probe Memory Shows the PC’s memory load, memory usage, and paging file usage. Device Summary Shows a summary of devices in your PC. DMI Explorer Shows information pertinent to the PC, such as CPU type, CPU speed, and internal/external frequencies, and memory size. Utility Lets you run programs outside of the ASUS Probe modules. To run a program, click Execute Program. NOTE: This feature is currently unavailable.
6. S/W REFERENCE ASUS PC Probe 6. SOFTWARE REFERENCE 6.1.3 ASUS PC Probe Task Bar Icon Right clicking the PC Probe icon will bring up a menu to open or exit ASUS PC Probe and pause or resume all system monitoring. When the ASUS PC Probe senses a problem with your PC, portions of the ASUS PC Probe icon changes to red, the PC speaker beeps, and the ASUS PC Probe monitor is displayed.
6. SOFTWARE REFERENCE 6. S/W REFERENCE ASUS Update 6.2 ASUS Update ASUS LiveUpdate is a utility that allows you to update your motherboard’s BIOS and drivers. The use of this utility requires that you are properly connected to the Internet through an Internet Service Provider (ISP). 1. Start ASUS Update Launch the utility from Start | Programs | ASUS Utility | ASUS Update Vx.xx. 2. Select an update method. 3.
6. S/W REFERENCE XGPlayer 6. SOFTWARE REFERENCE 6.3 YAMAHA XGPlayer The XGplayer is an application that is used to playback multimedia files. The XGplayer allows playback of MIDI files (.mid, .rmi), audio files (.wav, .mp3), movie files (.avi, .mpg) and audio CDs all from a single application. With MIDI files, you can mix, arrange (change voices/effects) and attach MIDI files to e-mails. Also, its links to various Internet services allows you to listen to music on web sites or purchase music easily. 6.3.
6. SOFTWARE REFERENCE 6. S/W REFERENCE XGPlayer 6.3.4 Troubleshooting Cannot install • • • Do you have the required hardware, such as hard disk and memory? Do you have the required software, such as MS-DOS and Windows? Installation may not be possible if you have insufficient space on your hard disk. Delete unneeded files to increase the free space on your disk.
7. APPENDIX 7. APPENDIX ASUS LAN Card 7.1 PCI-L101 Fast Ethernet Card LEDs LAN Activity Output Signal Intel Chipset RJ45 Wake on LAN Output Signal ASUS Motherboard type Other If you are using the ASUS PCI-L101 on an ASUS motherboard, leave the jumper on its defaut setting of “ASUS.” If you are using another brand of motherboard, set the jumper to “Other.” Connect the Wake on LAN (WOL) output signal to the motherboard’s WOL_CON in order to utilize the wake on LAN feature of the motherboard.
7. APPENDIX 7.1.1 Features 7. APPENDIX ASUS LAN Card • • • • • • • • • • • • Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX) Wake-On-LAN Remote Control Function Supported PCI Bus Master Complies to PCI Local Bus Rev. 2.1 specifications Consists of MAC & PHY (10/100Mbps) interfaces Complies to IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX interfaces Fully supports 10BASE-T & 100BASE-TX operations through a single RJ45 port Supports 32-bit Bus Master Technology / PCI Rev. 2.
7. APPENDIX 7.2 Modem Riser 7.2.1 56K Software Modem 7.2.2 Primary/Seconday MR There are two types of modem risers: primary MR and secondary MR. In appearance, the primary MR has a crystal onboard but the secondary does not. If your motherboard has an audio codec and no PCI audio chipset onboard, you may use the secondary MR; otherwise, you should use the primary MR. Layout of Primary MR Top: 7.
7. APPENDIX 7.2.4 Software Setup in Windows 98 The Modem Riser supports the Plug and Play feature. It allows your computer to automatically set the optimal configurations for the MR and communication software. Follow the procedure below to install the modem driver. 1. Power ON the computer after the hardware installation is completed. 7. APPENDIX Modem Riser 2. Windows 98 will automatically detect the modem and display a “PCI Card” message under “Add New Hardware Found”. 3.
7. APPENDIX 7.3 ASUS CIDB Intrusion Detection Module Connectors to detect intrusion by chassis mounted micro switches 7. APPENDIX ASUS CIDB Module The optional ASUS CIDB is a module for providing audible intrusion alarm and logging for ASUS motherboards equipped with the chassis connector. The module detects a chassis intrusion by either light striking its photo sensor or by the closing or opening of a chassis-mounted momentary toggle switch.
7. APPENDIX 5. To stop the alarm from sounding, use the BIOS setup or momentarily place a jumper on (or short manually) the CLR jumper. Note that the jumper must be removed for the CIDB to work normally again. 6. If you have an updated BIOS with intrusion support, booting the computer after an intrusion may require a password if configured through BIOS. 7.3.2 Setting up the ASUS CIDB 7.
7. APPENDIX 7.4 Glossary Bus PCI AGP 1X AGP 2X AGP 4X Bus Frequency 33MHz 66MHz 66MHz 66MHz Bandwidth 33MHz 66MHz 133MHz 266MHz 7 . APPENDIX Glossary 1394 1394 is the IEEE designation for the high performance serial bus at 12.5, 25 or 50MBytes/sec speeds. This serial bus defines both a back plane physical layer and a point-to-point cable-connected virtual bus.
7. APPENDIX 7. APPENDIX Glossary Boot Boot means to start the computer operating system by loading it into system memory. When the manual instructs you to “boot” your system (or computer), it means to turn ON your computer. “Reboot” means to restart your computer. When using Windows 95 or later, selecting “Restart” from “Start | Shut Down...” will reboot your computer. Bus Master IDE PIO (Programmable I/O) IDE requires that the CPU be involved in IDE access and waiting for mechanical events.
7. APPENDIX ASUS CUC2000 User’s Manual 7 . APPENDIX Glossary LPT Port (Line Printer Port) Logical device name reserved by DOS for the computer parallel ports. Each LPT port is configured to use a different IRQ and address assignment. MMX A set of 57 new instructions based on a technique called Single Instruction, Multiple Data (SIMD), which is built into the new Intel Pentium PP/MT (P55C) and Pentium II (Klamath) CPU as well as other x86-compatible microprocessors.
7. APPENDIX 7. APPENDIX Glossary ROM (Read Only Memory) ROM is nonvolatile memory used to store permanent programs (called firmware) used in certain computer components. Flash ROM (or EEPROM) can be reprogrammed with new programs (or BIOS). SCSI (Small Computer System Interface) High speed multi-threaded I/O interface defined by the X3T9.2 committee of the American National Standards Institute (ANSI) for connecting many peripheral devices.
INDEX Symbols ATX Power Supply 42 Audio Port 34 8-bit, 16-bit I/O Recovery Time 63 Floppy Disk Drive 35 IDE 35 A Infrared Module 38 Internal Audio 38 AC PWR Loss Restart 72 Internal Speaker 39 Accelerated Graphics Port 31 Joystick 34 Keyboard 32 Accessories CIDB Intrusion Detection Module 107 MIDI 34 Parallel Port 33 Fast Ethernet Card 103 Power Supply Thermal Sensor 42 Modem Riser 105 PS/2 Keyboard 32 Adobe Acrobat Reader Setup 92 PS/2 Mouse 32 AGP 31 Serial Port 33 ASUS PC Probe SMBus 39, 40 Setup 88 The
INDEX H L Halt On 57 Hardware Setup CIDB Module 108 CPU Installation 27 HDD Power Down 71 Head 55 Headers Digital Audio Interface 39 USB 39 High Priority PCI Mode 63 Language 57 LDCM Administrator Setup 82 LDCM Client Setup 84 Leads Chassis Intrusion 34 IDE Activity LED 37 Keyboard Lock Switch 41 Reset Switch 41 System Message LED 41 System Power LED 41 Legacy Diskette A 52 Legacy Diskette B 52 Load Setup Defaults 78 I IDE Activity LED Lead 37 IDE Connectors 35 IDE Hard Drive 75 INF Update Utility 86 In
INDEX Setup 90, 91 PCI Latency Timer 66 PCI/VGA Palette Snoop 66 PIO Mode 55 Plug & Play O/S 76 Power Fan Speed 74 Power Management 70 Procedure CPU Installation 27 Procedures Modem Riser Installation 105 Updating BIOS 46 PS/2 Keyboard Connector 32 PS/2 Mouse Connector 32 PWR Button < 4 Secs 71 PWR Up On Modem Act 72 Q ASUS PC Probe 88 ASUS Update 89 Intel LDCM Admin 82 Intel LDCM Client 84 LDCM Administrator 82 LDCM Client 84 PC-Cillin 98 90, 91 Starting Up 43 Supervisor Password 57 Suspend Mode 71 Suspe
INDEX +5 74 -12 74 -5 74 VCORE 74 W Wake On LAN 72 Wake On PS2 KB/PS2 Mouse/CIR 73 Wake Up By Keyboard 73 Wake-On-LAN Connector 36 Wake-On-Ring Connector 36 116 ASUS CUC2000 User’s Manual
® Goes Mobile! L8400 Series Compact Professional Notebook PC • • • • • 14.1” TFT Color Display 450MHz to 700MHz+ 64MB to 192MB Memory 2X AGP 3D w/8MB VRAM 100MHz Processor Side Bus M8300/8200 Series Thin & Light Convertible Notebook PC • • • • 13.3” or 12.1” TFT Color Display 366MHz to 650MHz+ 64MB to 192MB Memory Supports Two Hard Drives L7300/7200 Series All-in-One Compact Notebook PC • 13.3” or 12.1” TFT Color Display • 366MHz to 650MHz+ • 64MB to 192MB Memory Visit www.asus.
® Barebone Servers Pentium® III PC100 ECC Ultra2 SCSI 5.25” Pentium® II Max. Memory Onboard Fixed Storage Support (GB) (Channels) Devices Hot-Swap Trays AP100 1 1 1 3 0 AP200 2 1 1 3 0 AP2000 2 1 1 4 3 or 5* AP2500 2 1 1 4 3 or 5* AP3000 2 Xeon™ 2 2 4 3 or 5* AP6000 2 1 1 4 8** AP7500 2 1 1 4 8** AP8000 2 Xeon™ 2 2 4 8** * ** Three 1.6-inch or five 1-inch SCA-2 SCSI hard drives Eight 1.
ASUS AR1000 RAID Sub-system with DA3000 SCSI-to-SCSI RAID Controller • • • • • • • • • • • • • • • • Supports 5x86 RAID processor and two 72-pin SIMM sockets for up to 128MB cache memory Supports three Ultra2 SCSI channels; up to 80MB/sec data transfer rate Supports multiple Host/Drive channel capacity Redundant controller capacity Supports non-RAID, RAID levels 0, 1, 0+1, 3, 5 On-line failure drive rebuilding Automatic rebuilding — supports local/global spare drive On-line expansion capacity Supports SAF-
® 8x DVD-ROM Drive • Industry-leading performance for even the most demanding applications • Maximum transfer rate: 8X DVD-ROM / 40X CD-ROM • High speed digital audio extraction • Supports UltraDMA/33 transfer mode • Complies with MPC3 standard • Supports Multi-Read function ® Ultra-Fast CD-ROM • • • • • Supports high speed CD-Audio playback Supports high speed digital audio extraction Supports UltraDMA/33 transfer mode Compatible with all CD formats Supports multi-read function (CD-R/CD-RW) Visit www
Visit www.asus.
