Notebook PC Hardware Reference Product Name: Notebook PC Hardware Manual Revision: 1.
Safety Statements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules.
Safety Statements Nordic Cautions (for Notebook PC with Lithium-Ion Battery) CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. (English) VORSICHT! Explosionsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ.
Safety Statements Safety Precautions WARNING! The following safety precautions will increase the life of the Notebook PC. Follow all precautions and instructions. Except as described in this manual, refer all servicing to qualified personnel. Do not use damaged power cords, accessories, or other peripherals. Do not use strong solvents such as thinners, benzene, or other chemicals on or near the surface. Disconnect the AC power and remove the battery pack(s) before cleaning.
Safety Statements Transportation Precautions To prepare the Notebook PC for transport, you should turn it OFF and disconnect all external peripherals to prevent damage to the connectors. The hard disk drive’s head retracts when the power is turned OFF to prevent scratching of the hard disk surface during transport. Therefore, you should not transport the Notebook PC while the power is still ON.
Safety Statements CTR 21 Approval (for Notebook PC with built-in Modem) Danish Dutch English Finnish French German Greek Italian Portuguese Spanish Swedish
Safety Statements UL Safety Notices Required for UL 1459 covering telecommunications (telephone) equipment intended to be electrically connected to a telecommunication network that has an operating voltage to ground that does not exceed 200V peak, 300V peak-to-peak, and 105V rms, and installed or used in accordance with the National Electrical Code (NFPA 70).
Table of Contents 1. Introducing the Notebook PC 11 About This User’s Manual ..................................................................................................... 12 Notes For This Manual ..................................................................................................... 12 2. Knowing the Parts 13 Top Side ................................................................................................................................ 14 Bottom Side ....................
Table of Contents 4. Using the Notebook PC 35 Pointing Device ..................................................................................................................... 36 Using the Touchpad ......................................................................................................... 36 Touchpad Usage Illustrations ........................................................................................... 36 Caring for the Touchpad ..................................................
Table of Contents Power Management Modes .................................................................................................. 59 Full Power Mode & Maximum Performance .................................................................... 59 ACPI ................................................................................................................................. 59 Suspend Mode ............................................................................................................
1.
Introducing the Notebook PC About This User’s Manual You are reading the Notebook PC User’s Manual. This User’s Manual provides information on the various components in the Notebook PC and how to use them. The following are major sections of this User’s Manuals: 1. Introducing the Notebook PC Introduces you to the Notebook PC and this User’s Manual. 2. Knowing the Parts Gives you information on the Notebook PC’s components. 3. Getting Started Gives you information on getting started with the Notebook PC.
2.
Knowing the Parts Top Side Refer to the diagram below to identify the components on the top side of the Notebook PC.
Knowing the Parts Display Panel The display panel functions the same as a desktop monitor. The Notebook PC uses an active matrix TFT LCD, which provides excellent viewing like that of desktop monitors. Unlike desktop monitors, the LCD panel does not produce any radiation or flickering, so it is easier on the eyes. Display Panel Care The LCD screen is very delicate and requires careful handling.
Knowing the Parts Bottom Side Refer to the diagram below to identify the components on the bottom side of the Notebook PC. Reset Button Memory Compartment Mini-PCI Compartment for Modem & LAN Hard Drive Compartment Module Drive Bay or Additional Battery Compartment Main Battery Compartment WARNING! The bottom of the Notebook PC can get very hot. Be careful when handling the Notebook PC while it is in operation or recently been in operation. High temperatures are normal during charging or operation.
Knowing the Parts The following describes the components on the bottom side of the Notebook PC as shown by the illustration on the previous page. Memory Compartment The memory compartment contains 2 SO-DIMM slots for memory installation. There is no memory built in, so one memory module must be installed in order for the Notebook PC to function. Memory installation/upgrades must be done by an authorized retailer or else warranty will be void.
Knowing the Parts Left Side Refer to the diagram below to identify the components on the left side of the Notebook PC. Volume Control Fast IrDA Port Hard Drive PC Card PC Card Compartment (PCMCIA) Eject (see bottom side) Sockets Left Audio Speaker Fast Infrared Port (IrDA) The fast infrared (IrDA) communication port allows convenient wireless data communication with infrared-equipped devices or computers up to 4 Mbits/sec.
Knowing the Parts The following describes the components on the right side of the Notebook PC as shown by the illustration above. Right Audio Speaker (See Left Side) PS/2 Port The PS/2 port is for connecting an external PS/2 mouse or PS/2 keyboard to the Notebook PC if you do not want to use the built-in pointing device and keyboard. Simultaneous use of two PS/2 devices requires an optional PS/2 Y-adapter.
Knowing the Parts Rear Side Refer to the diagram below to identify the components on the rear side of the Notebook PC. 1 Serial Port TV TV-Out Air Vent & Fan 1394 and PortBar Combo Model (1) Portbar Port (1) 1394 Port Parallel Port External Monitor Port Modem LAN Port Port (RJ-11) (RJ-45) PortBar Only Model 1394 Only Model (1) Portbar Port (2) IEEE 1394 Ports The following describes the components on the rear side of the Notebook PC as shown by the illustration above.
Knowing the Parts External Monitor Port The 15-pin D-sub monitor port supports a standard VGA-compatible device such as a monitor or projector to allow viewing on a larger external display. LAN Port The RJ-45 LAN port supports an RJ-45 Ethernet cable. The internal LAN supports 10Base-T or 100BaseTX standard or duplex networks. The built-in connector allows convenient use without a dongle. Modem Port The RJ-11 telephone port supports an RJ-11 telephone cable. The internal modem supports up to 56K V.
Knowing the Parts Front Side Refer to the diagram below to identify the components on the front side of the Notebook PC. Display Panel Latch Battery Compartment (see bottom side) Status Indicators Module Drive Bay or Second Battery Compartment (see bottom side) Display Panel Latch One display panel latch is used to lock the display panel in the closed position. To open the display panel, slide the latch to the right with your thumb and lift up the display panel at the same time.
3.
Getting Started Installing and Removing the Battery Pack Your Notebook PC may or may not have its battery pack installed. If your Notebook PC does not have its battery pack installed, there will be a large opening at the bottom of the Notebook PC. Use the following procedures to install or remove the battery pack. To install the battery pack: 1. Insert the battery pack with the connector side first and you will hear a loud click when the battery pack locks into place. To remove the battery pack: 1 1.
Getting Started Using the Battery Pack Before you use your Notebook PC on the road, you will have to charge the battery pack. The battery pack begins to charge as soon as the Notebook PC is connected to external power. Fully charge the battery pack before using it for the first time. A new battery pack must completely charge before the Notebook PC is disconnected from external power. The battery pack is about 85% charged when the battery charge light turns OFF.
Getting Started Power Connection Your Notebook PC comes with a universal AC-DC adapter. That means that you may connect the power cord to any 110V-120V as well as 220V-240V outlets without setting switches or using power converters. Different countries may require that an adapter be used to connect the provided US-standard AC power cord to a different standard. Most hotels will provide universal outlets to support different power cords as well as voltages.
Getting Started Powering ON The Notebook PC The Notebook PC’s power-ON message appears on the screen followed by a short beep when you turn it ON. If necessary, you may adjust the brightness by using the hot keys. If you need to run the BIOS Setup to set or modify the system configuration, press [F2] upon bootup to enter the BIOS Setup. If you press [Tab] during the splash screen, standard boot information such as the BIOS version can be seen.
Getting Started Power Management - Stand By & Hibernate Power management settings can be found in the Windows control panel. The following shows the power options properties in Windows ME. You can define Stand By or Power Off for closing the display panel, pressing the power button, or activating sleep mode. Basically Stand by and Hibernate saves power when your Notebook PC is not in use by turning OFF certain components.
Getting Started Using the Keyboard Colored Hot Keys The following defines the colored hot keys on the Notebook PC’s keyboard. The colored commands can only be accessed by first pressing and holding the function key while pressing a key with a colored command. NOTE: The Hot Key locations on the function keys may vary depending on model but the functions should remain the same. Follow the icons instead of the function keys (F1, F5, F6, etc.
Getting Started Instant Launch Keys and Status Indicators Above the Keyboard 1 Front Edge of Notebook PC A Instant Launch Keys M-Mode The M-Mode button toggles power savings ON or OFF. When power savings is activated, CPU speed and LCD brightness will be decreased. M-Mode will decrease power consumption even more if used together with Intel SpeedStep. M-Mode works only in battery mode and Intel SpeedStep will work in battery or AC mode but requires manual configuration to work in AC mode.
Getting Started Status Indicators (Top) M-Mode When the LED is not lit (OFF), the Notebook PC is running in full power mode (M-Mode is not activated). When the LED is lit (ON), the Notebook PC is running in power savings mode (M-Mode is activated). Activity Indicator Indicates that the Notebook PC is accessing one or more storage device(s) such as the hard disk or optical storage drive. The light flashes proportional to the access time.
Getting Started Microsoft Windows™ Keys There are two special Windows™ keys on the keyboard as described below. The key with the Windows™ Logo activates the Start menu located at the bottom left of the Windows™ desktop. The other key, that looks like a Windows™ menu with a small cursor, activates the properties menu and is equivalent to pressing the right mouse button on a Windows™ object.
Getting Started Keyboard as Cursors The keyboard can be used as cursors while Number Lock is ON or OFF in order to increase navigation ease while entering numeric data in spreadsheets or similar applications. With Number Lock OFF, press and one of the cursor keys shown below. For example [Fn][8] for up, [Fn][K] for down, [Fn][U] for left, and [Fn][O] for right. With Number Lock ON, use [Shift] and one of the cursor keys shown below.
Getting Started 34
4.
Using the Notebook PC Pointing Device The Notebook PC’s integrated touchpad pointing device is fully compatible with all two/three-button and scrolling knob PS/2 mice. The touchpad is pressure sensitive and contains no moving parts; therefore, mechanical failures can be avoided. A device driver is still required for working with some application software. See the Driver & Utility Guide for information on drivers and utilities for the touchpad.
Using the Notebook PC Clicking/Tapping - With the cursor over an item, press the left button or use your fingertip to touch the touchpad lightly, keeping your finger on the touchpad until the item is selected. The selected item will change color. The following 2 examples produce the same results.
Using the Notebook PC Dragging - Dragging means to pick up an item and place it anywhere on the screen you wish. You can move the cursor over the item you select, and while keeping the left button depressed, moving the cursor to the desired location, then release the button. Or, you can simply double-tap on the item and hold while dragging the item with your fingertip. The following 2 examples produce the same results.
Using the Notebook PC Floppy Disk Drive Module (Included) For an All-In-One configuration, use a floppy disk module connected to the parallel port using the provided cable. This is the same floppy disk module that fits in the Notebook PC’s internal module drive bay. NOTE: The floppy disk drive module does not support plug and play, you must shut down the Notebook PC when connecting or disconnecting the floppy disk drive module either from the parallel port or from the module drive bay.
Using the Notebook PC Additional Battery Pack (Optional) Flip the Notebook PC over to access the underside. The left side is a combination module bay and battery bay and the right side is a permanent battery bay. Follow these instructions for inserting an additional battery pack. 2 Remove module drive 1 Slide and hold the drive lock (arrow 1). While holding drive lock (arrow 1), slide the eject mechanism (arrow 2) forcefully until the drive ejects. Pull the drive module out (arrow 3).
Using the Notebook PC PortBar Accessory (Optional) This section is provided for the optional PortBar accessory for the Notebook PC. The main purpose of the PortBar is to provide a simple inexpensive desktop docking solution as compared to traditional bulky port replicators. Depending on the power requirements of your Notebook PC, it may support either one of the two PortBar models. PortBar 1 (front view) Triangular icon or brand name faces up.
Using the Notebook PC PortBar Accessory (Optional) The major differences between the two PortBar models: • Currently, PortBar2 is not supported on this Notebook PC. • PortBar 2 has both 50W & 60W power pass through, whereas PortBar 1 only has a 50W power pass through. • PortBar 2 has a LAN pass through & only one PS/2 port, whereas PortBar 1 has two PS/2 ports. Triangular icon or brand name faces up.
Using the Notebook PC PortBar Accessory (Optional) Features The PortBar features a DC pass-through for powering the PortBar and the Notebook PC, VGA port for an external monitor, one PS/2 port for either a PS/2 mouse or PS/2 keyboard (dual use possible with a PS/2 “Y” adapter), two USB ports, RJ45 LAN port, and parallel port.
Using the Notebook PC Second Hard Disk Drive Module (Optional) The convenient design of the Notebook PC allows for the usage of a second hard disk drive in the modular bay. A second hard disk drive allows you to use it as a removable device, for installing dual operating systems, for additional data storage, or to store CDs. To use a second hard disk drive, you must be familiar with the following: • What to purchase and the contents of the kit.
Using the Notebook PC Optical Drive Modules (Optional) The Module Bay provides a convenient solution to add an additional device such as: • • CD-ROM DVD-ROM + CD-RW • • CD-RW Second Hard Disk • DVD-ROM WARNING: Shut down the Notebook PC before inserting or removing module drives to prevent the system from hanging. The CD-ROM (Compact Disc Read Only Memory) drive can support all the popular formats: Audio/ Music CDs; Photo CDs; MS-DOS MSCDEX Mode 1 / Mode 2; CD-ROM/XA; CD-I; and Video CDs.
Using the Notebook PC Inserting a drive module Module drives like the CD-ROM can be inserted in to the module drive bay. The module drives can be inserted while the Notebook PC is right-side up or flipped over. Inserting an optical disc 1. While the Notebook PC’s power is ON, press the drive’s eject button and the tray will eject out partially. 2. Gently pull on the drive’s front panel and slide the tray completely out. Be careful not to touch the CD drive lens and other mechanisms.
Using the Notebook PC Using the CD-ROM Drive CD-ROM discs and equipment must be handled with care because of the precise mechanics involved. Keep in mind the important safety instructions from your CD suppliers. Unlike desktop CD-ROM drives, the Notebook PC uses a hub to hold the CD in place regardless of the angle. When inserting a CD, it is important that the CD be pressed onto the center hub or else the CD-ROM drive tray will scratch the CD.
Using the Notebook PC Regional Playback Information Playback of DVD movie titles involves decoding MPEG2 video, digital AC3 audio and decryption of CSS protected content. CSS (sometimes called copy guard) is the name given to the content protection scheme adopted by the motion picture industry to satisfy a need to protect against unlawful content duplication. Although the design rules imposed on CSS licensors are many, one rule that is most relevant is playback restrictions on regionalized content.
Using the Notebook PC Using a CD A CD drive letter should be present regardless of the presence of a CD disc in the drive. After the CD is properly inserted, data can be accessed just like with hard disk drives; except that nothing can be written to or changed on the CD. Vibration is normal for all high-speed CD-ROM drives due to unbalanced CDs or CD print. To decrease vibration, use the Notebook PC on an even surface and do not place labels on the CD.
Using the Notebook PC Optional External Connections Monitor Out Connection Connecting an external monitor is just like on a standard desktop PC. Just plug in the VGA cable and its ready to use (some Notebook PC configurations may require additional display driver settings). You can view the Notebook PC display panel while simultaneously allowing others to view the external monitor. For large audiences, try connecting a computer video projector.
Using the Notebook PC Optional External Audio Connections External Audio Connections The Notebook PC provides easy access for connecting a stereo headphone, mono microphone, and a stereo audio source just like on some personal tape recorders. SPDIF Audio Connection The headphone jack also doubles as a SPDIF audio port. The SPDIF port carries undecoded digital audio signal (AC3 or DTS) using an optional fiber optics cable to your home theater system.
Using the Notebook PC PC Card (PCMCIA) Socket The Notebook PC supports PC Cards (or sometimes referred to as PCMCIA cards) to allow expansion like PCI cards on desktop computers. This allows you to customize your Notebook PC to meet a wide range of application needs. The PCMCIA socket can interface with type I or type II PC cards. PC cards are about the size of a few stacked credit cards and have a 68-pin connector at one end.
Using the Notebook PC Inserting a PC Card (PCMCIA) 1. Insert the PC card with the connector side first. When the PC card is fully inserted, the PC card bay door can close normally without striking the PC card. 2. Carefully connect any cables or adapters needed by the PC card. Usually connectors can only be inserted in one orientation. Look for a sticker, icon, or marking on one side of the connector representing the top side. T R E S IN IS H T D N E Be sure the PC card is level when inserting.
Using the Notebook PC Modem and Network Connections The built-in modem and network model comes with both an RJ-11 and an RJ-45 port. RJ-11 telephone cables have two or four wires and are used to connect telephones to telephone outlets found in the walls of residential homes and some commercial buildings (some commercial buildings may have telephone wiring designed for dedicated phone systems that may not be compatible).
Using the Notebook PC Network Connection Connect a network cable, with RJ-45 connectors on each end, to the modem/network port on the Notebook PC and the other end to a hub or switch. For 100BASE-TX speeds, your network cable must be category 5 (not category 3) with twisted-pair wiring. If you plan on running the interface at 100Mbps, it must be connected to a 100BASE-TX hub (not a 100BASE-T4 hub). For 10Base-T, use category 3, 4, or 5 twisted-pair wiring.
Using the Notebook PC IR Wireless Communication The Notebook PC is equipped with a conveniently located Infrared (IR) Communication Port (see 2. Knowing the Parts for location). The IR port comes with IrDA (Infrared Data Association) Serial Infrared Data Link Version 1.1 compliance, that allows you to perform point-to-point wireless communications. You can use a FIR-specified application to transmit or receive data files with other systems equipped with an infrared port.
Using the Notebook PC CAUTION! Disable the infrared communication when you are not using the IR for long periods because the IR consumes a great deal of Windows resources which will decrease the Notebook PC’s performance. AC Power System The Notebook PC power is comprised of two parts, the power adapter and the battery power system. The power adapter converts AC power from a wall outlet to the DC power required by the Notebook PC. The battery pack consists of a set of battery cells housed together.
Using the Notebook PC Using Battery Power A fully-charged battery pack provides the Notebook PC a few hours of working power. But the actual figure varies depending on how you use the power saving features, your general work habits, the CPU, system memory size, and the size of the display panel. The “Battery Warning” beeps are automatically enabled in Windows ME and beeps once when down to 10% (configurable in Windows ME) power. The processor is also throttled down to decrease power use.
Using the Notebook PC Power Management Modes The Notebook PC has a number of automatic or adjustable power saving features that you can use to maximize battery life and lower Total Cost of Ownership (TCO). You can control some of these features through the Power menu in the BIOS Setup. ACPI power management settings are made through the operating system.
Using the Notebook PC Power Savings In addition to reducing the CPU clock, this mode puts devices including the LCD backlight in their lower active state. The Notebook PC enters Standby mode (low priority) when the system remains idle for a specified amount of time. The timeout can be set through BIOS setup (lower priority) and Windows power management (higher priority). To resume system operation, press any key.
Using the Notebook PC System Memory Expansion Memory must be installed in order to use the Notebook PC. Under some circumstances, you may find additional memory is required. This is particularly true as applications become more complex. Expanding system memory is one method of increasing system performance by decreasing hard disk access. The Notebook PC comes with no memory built-in.
Using the Notebook PC External Keyboard Connection To allow easier data entry, you may connect any PS/ 2 keyboard as shown here. External Mouse Connection A USB mouse can be easily connected to the Notebook PC. There is only one correct orientation with the USB symbol facing upwards. The USB mouse will work simultaneously with the Notebook PC’s touchpad. For more than one USB connection, you can purchase either a separate hub or a keyboard with integrated USB hub.
Using the Notebook PC Securing Your Notebook PC (Optional) For system and hard disk drive security, see BIOS setup “Security”. A third party lock such as the ones by Kensington® can be used to secure your Notebook PC physically to an unmovable object. The cable wraps around an object and the “T” shaped end inserts into the Kensington® lock port as shown in this illustration and a key or combination dial is used to secure the lock in place.
Using the Notebook PC 64
5.
Configuring the BIOS BIOS Setup Program This Notebook PC supports a programmable EEPROM that stores the BIOS software and can be updated using the provided flash memory writer utility. This Section will guide you through the BIOS setup program by providing clear explanations for all the options. A default configuration has already been set. If you are either installing new devices or expanding main memory, you will need to enter the BIOS Setup to reconfigure your Notebook PC.
Configuring the BIOS Updating your BIOS This Notebook PC supports an easy-to-use BIOS update software called “WINFLASH” which is installed through the provided support CD. If you need help installing or using “WINFLASH”, refer to the “Driver & Utility Manual”. BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration.
Configuring the BIOS General Help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing [F1] or the [Alt] + [H] combination. The General Help screen lists the legend keys with their corresponding alternates and functions. Scroll Bar When a scroll bar appears to the right of a help window, it indicates that there is more information to be displayed that will not fit in the window.
Configuring the BIOS Main Menu When the Setup program is accessed, the main menu screen appears as shown: Item Specific Help System Time System Date Floppy Disk Drive Floppy 3 Mode [17:15:00] [08/30/2001] [1.44M, 3.5 in.] [Disabled] Primary Master Secondary Master Video Display Device Installed Memory Video RAM Size [IBM-DJSA-220] [TOSHIBA DVD-ROM SD-C2502] [LCD & CRT] 128 MB [ 16MB] to select field; <+>,<-> to change value.
Configuring the BIOS Floppy 3 Mode [Disabled] This is required to support older Japanese floppy disk drives. Floppy 3 Mode will allow reading and writing of 1.2MB (as opposed to 1.44MB) on a 3.5-inch diskette. Configuration options: [Disabled] [Enabled] >Primary Master (described later) >Secondary Master (described later) Video Display Device [CRT] This field allows you to select and enable video display devices, such as an LCD panel, an external CRT/LCD monitor, or both.
Configuring the BIOS Primary Master (sub-menu) This field is used to configure the primary IDE drive installed in the system. To configure a hard disk drive, select this sub-menu from the Main menu and press the Enter key to enter this sub-menu.
Configuring the BIOS Cylinders [ ] This field configures the number of cylinders. Refer to your drive documentation to determine the correct value to enter into this field. NOTE: To make changes to this field, the Type field must be set to User Type HDD and “Translation Method” must be set to Manual. Heads [ ] This field configures the number of read/write heads. Refer to your drive documentation to determine the correct value to enter into this field.
Configuring the BIOS Secondary Master (sub-menus) This field is used to configure the secondary IDE drive installed in the system. To configure a hard disk drive, select this sub-menu from the Main menu and press the Enter key to enter this sub-menu. The fields and options on this sub-menu are the same as the previous menu described earlier. Leave on the default setting of Auto.
Configuring the BIOS Advanced Menu Selecting Advanced from the main menu bar display the Advanced menu as shown below. Item Specific Help I/O Device Configuration LCD Expansion Processor Serial Number Quick Power On Self Test TV Type Select [Enabled] [Enabled] [Enabled] [US NTSC] to go to the sub-menu. >I/O Device Configuration (described on next page) Pressing [Enter] when this field is highlighted calls up a sub-menu for configuring the Notebook PC’s serial and parallel ports.
Configuring the BIOS I/O Device Configuration (sub-menu) I/O Device Configuration Serial Port A: [3F8H/IRQ4] IR Port Mode [0E00H/IRQ3] [FIR] Parallel Port Mode [378H/IRQ7] [Bi-dir] Item Specific Help to select the I/O Address & IRQ for Infrared. NOTE: The presence of sub-items in this menu is dependent on certain relevant settings. WARNING! Changing the default address and IRQ settings for Serial Port or Parallel Port can cause conflicts with other system devices or installed peripherals.
Configuring the BIOS Parallel Port: [378H/IRQ7] This field allows you to configure the Notebook PC parallel port. The configuration options are: [Disabled] [378H/IRQ7] [278H/IRQ5] Mode: [Bi-dir] The Mode field allows you to configure the Notebook PC parallel port transmission mode. The configuration options are: [Normal] [Bi-dir] [ECP] [EPP] EPP Mode: When the EPP mode is selected, the standard and bidirectional modes are also available. The EPP operates on a two phase cycle.
Configuring the BIOS Security Menu The Notebook PC’s advanced system of security allows you to set a password to prevent unauthorized access to system resources, data, and the BIOS Setup Program. This Section covers each parameter of the Security Setup. Selecting Security from the menu bar displays the following menu: Item Specific Help System Password Hard disk Password Finger Print Security [Disabled] [Disabled] [Disabled] Supervisor password controls full access.
Configuring the BIOS System Password [Disabled] The system password protects the BIOS settings. When “Enabled”, you will be prompted for a password after you press [F2] to enter BIOS setup. To Enable: Select the “Disabled” item and press [Enter], type a password and press [Enter], type the same password again and press [Enter] to confirm. (You can type up to eight alphanumeric characters. Symbols and other keys are ignored.
Configuring the BIOS Power Menu The power management settings are controlled by the operating system. This menu only has one function as follows: Item Specific Help CPU Auto Power Saving LCD Auto Power Saving [Disabled] [Disabled] Start Battery Refreshing By slowing down CPU speed when AC adapter not in use to conserve battery power CPU Auto Power Saving [Disabled] Enabling this item will decrease the CPU speed when the AC power is not connected in order to conserve battery power.
Configuring the BIOS Boot Menu The Boot menu allows the user to specify the order in which the Notebook PC is to check for a device to boot the system. To make changes, select Boot from the menu bar and the following screen appears: Item Specific Help 1. Removable Device 2. IDE Hard Drive 3. ATAPI CD-ROM 4. Other Boot Device [Floppy Module] [IBM-DJSA-220] [TOSHIBA DVD-ROM SD-C2402] [Disabled] Boot Sequence: to select the device. To select the boot sequence, use the up or down arrow.
Configuring the BIOS Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Exit setup utility and save your changes to CMOS. NOTE: Pressing the [Esc] key does not exit this menu.
Configuring the BIOS Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When this option is selected or if [F9] is pressed, a confirmation is requested. Select Yes to load default values programmed into the BIOS file (the default values may change from one BIOS version to another). You can now select Exit Saving Changes or make other changes before saving the values to the EEPROM.
APPENDIX Appendix Fingerprint Authentication System (on selected models) Internal Modem Compliancy Glossary Owner Information A
Appendix Fingerprint Authentication System If you purchased the Notebook PC model with Fingerprint Identification, you need to read this section to understand how to use it. Opening Screen - Standby Preboot Authentication, V5.018 RIO V2.3 AES4000 Fingerprint Confirmed Preboot Authentication, V5.018 RIO V2.
A Appendix Fingerprint Authentication System (cont’) Authentication Setup Menu Preboot Authentication, V5.018 RIO V2.3 AES4000 Add New User Preboot Authentication, V5.018 RIO V2.3 AES4000 Add new user Erase all information Change admin. status User name? add Fingerprint List users change Security level _ Delete user delete fingerPrint eXit Use arrow keys to highlight a menu item, see detailed description below With the desired option highlighted press ...
Appendix Fingerprint Authentication System (cont’) Authentication Setup Menu Preboot Authentication, V5.018 RIO V2.3 AES4000 Add new user Erase all information Change admin. status add Fingerprint List users change Security level Delete user delete fingerPrint eXit Erase all information Preboot Authentication, V5.018 RIO V2.
Appendix A Fingerprint Authentication System (cont’) Authentication Setup Menu Change Admin. Status Preboot Authentication, V5.018 RIO V2.3 AES4000 Add new user Erase all information Change admin. status add Fingerprint List users change Security level Delete user delete fingerPrint eXit Preboot Authentication, V5.018 RIO V2.3 AES4000 + User 1 User 2 + Use arrow keys to highlight a menu item, see detailed description below With the desired option highlighted press ...
Appendix Fingerprint Authentication System (cont’) Proper Finger Placement While the matching algorithm of the fingerprint authentication system is quite tolerant to non-optimum finger placement, centering the core on the sensor will give the best possible performance. [ ] The fingerprint “core” is approximately under the beginning of each fingernail, or about half way from the knuckle to the fingertip.
Appendix A Fingerprint Authentication System (cont’) Using the Full Fingerprint Capture the full area of the fingerprint by contacting the sensor with the finger placed flat on the sensor, as opposed to presenting only the tip of the finger. The fingertip alone contains insufficient image data for a high-quality fingerprint. The ridges in this area are mostly parallel lines, with few distinct minutiae from which to construct an identification template.
Appendix Centering the Core In some cases, if the core of the fingerprint is not visible in the image on the screen, the software may incorrectly reject a registered user. In this case, simply lift the finger and replace it on the sensor with the core more closely centered on the sensor. The matching process should then be performed correctly. During enrollment, you will be asked to lift and replace your finger on the sensor several times.
Appendix A Internal Modem Compliancy Protocols and Compliancy The Notebook PC with internal modem model complies with JATE (Japan), FCC (US, Canada, Korea, Taiwan), and CTR21. The internal modem has been approved in accordance with Council Decision 98/ 482/EC for pan-European single terminal connection to the public switched telephone network (PSTN).
Appendix This table shows the countries currently under the CTR21 standard.
Appendix A Glossary ACPI (Advanced Configuration and Power Management Interface) Modern standard for reducing power usage in computers. APM (Advanced Power Management) Modern standard for reducing power usage in computers. AWG (American Wire Gauge) Gauge AWG Diam (mm) Area (mm2) R (ohm/km) I@3A/mm2 (mA) Gauge AWG Diam (mm) Area (mm2) R (ohm/km) I@3A/mm2 (mA) 46 0.04 0.0013 13700 3.8 24 0.50 0.20 87.5 588 44 0.05 0.0020 8750 6 0.55 0.24 72.3 715 42 41 0.06 0.07 0.0028 0.
Appendix BIOS (Basic Input/Output System) BIOS is a set of routines that affect how the computer transfers data between computer components, such as memory, disks, and the display adapter. The BIOS instructions are built into the computer’s read-only memory. BIOS parameters can be configured by the user through the BIOS Setup program. The BIOS can be updated using the provided utility to copy a new BIOS file into the EEPROM. Bit (Binary Digit) Represents the smallest unit of data used by the computer.
Appendix A IDE (Integrated Drive Electronics) IDE devices integrate the drive control circuitry directly on the drive itself, eliminating the need for a separate adapter card (in the case for SCSI devices). UltraDMA/66 or 100 IDE devices can achieve up to 33MB/Sec transfer. IEEE1394 Also known as iLINK (Sony) or FireWire (Apple). IEEE1394 is a high speed serial bus like SCSI but has simple connections and hot-plugging capabilities like USB.
Appendix POST (Power On Self Test) When you turn on the computer, it will first run through the POST, a series of software-controlled diagnostic tests. The POST checks system memory, the motherboard circuitry, the display, the keyboard, the diskette drive, and other I/O devices. PS/2 Port PS/2 ports are based on IBM Micro Channel Architecture. This type of architecture transfers data through a 16-bit or 32-bit bus. A PS/2 mouse and/or keyboard may be used on ATX motherboards.
Appendix A Suspend Mode In Save-to-RAM (STR) and Save-to-Disk (STD), the CPU clock is stopped and most of the Notebook PC devices are put in their lowest active state. The Notebook PC enters Suspend when the system remains idle for a specified amount of time or manually using the function keys. The timeout setting of both Hard Disk and Video can be set by the BIOS Setup. The Power LED blinks when the Notebook PC is in STR mode. In STD mode, the Notebook PC will appear to be powered OFF.
Appendix 98
Appendix A Index A D AC Power System 56 APM and ACPI 59 Diskette A 69 Display Panel 15 Display Panel Latch 22 DVD-ROM Drive Information 47 B Battery Pack 24 Battery Power System 56 BIOS Advanced Menu 74 BIOS Legend Bar 67 BIOS Menu Bar 67 BIOS Setup Program 66 Boot Menu 80 Boot Sequence 80 Cylinders 72 Discard Changes 82 Exit Discarding Changes 81 Exit Menu 81 Exit Saving Changes 81 Heads 72 I/O Device Configuration 75 IR Port 75 Load Setup Defaults 82 Main Menu 69 Multi-Sector Transfers 72 Parallel P
Appendix N Network Connection 55 Nordic Cautions 3 Numeric Keypad, alternate 32 O Owner Information 102 P Parallel Port 20 PC Card (PCMCIA) Sockets 52 Pointing Device 36 Power Connection 26 Power Indicator 31 Power Management Modes 59 Power State Summary 60 Power Switch 15 Power-On Self Test (POST) 27 Powering OFF 28 Powering ON 27 Processor Upgrades 61 Programmable Launch Key 30 R Region Definitions 48 Regional Playback Information 48 Restarting or Rebooting 28 S Securing Your Notebook PC 64 Speaker 18
Appendix A 101
Appendix Owner Information This page is provided for recording information concerning your Notebook PC for future reference or for technical support. Keep this User’s Manual in a secured location if passwords are filled out.
