TS100-E8-PI4 Manual
Table Of Contents
- Contents
- Chapter 1: Product introduction
- Chapter 2: Hardware setup
- Chapter 3: Motherboard Info
- 3.1 Motherboard layout
- 3.2 Jumpers
- 3.3 Internal connectors
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Advanced menu
- 4.4.1 CPU Configuration
- 4.4.2 PCH-IO Configuration
- 4.4.3 SATA Configuration
- 4.4.4 System Agent (SA) Configuration
- 4.4.5 PCI Subsystem Settings
- 4.4.6 USB Configuration
- 4.4.7 TPM
- 4.4.8 ACPI Settings
- 4.4.9 WHEA Support
- 4.4.10 NCT6779D Super IO Configuration
- 4.4.11 Intel Server Platform Services
- 4.4.12 Onboard LAN Configuration
- 4.4.13 MIO Card Configuration
- 4.4.14 Serial Port Console Redirection
- 4.4.15 Runtime Error Logging Support
- 4.4.16 APM
- 4.4.17 Network Stack
- 4.4.18 Intel RC Drivers Version Detail
- 4.5 Event Logs menu
- 4.6 Boot menu
- 4.7 Monitor menu
- 4.8 Security
- 4.9 Tool menu
- 4.10 Exit menu
- Chapter 5: RAID configuration
- Chapter 6: Driver installation
4-26
Chapter 4: BIOS setup
Flow Control [Hardware RTS/CTS]
Flow control can prevent data loss from buffer overflow. When sending data, if the
receiving buffers are full, a “stop” signal can be sent to stop the data flow. Once the
buffers are empty, a “start” signal can be sent to re-start the flow. Hardware flow control
uses two wires to send start/stop signals. Configuration options: [None] [Hardware
RTS/CTS]
VT -UTF8 Combo Key Support [Enabled]
This allows you to enable the VT -UTF8 Combination Key Support for ANSI/VT100
terminals. Configuration options: [Disabled] [Enabled]
Recorder Mode [Disabled]
This allows you to enable or disable the Recorded mode to capture Terminal data.
Configuration options: [Disabled] [Enabled]
Resolution 100x31 [Enabled]
This allows you to enable or disable the extended terminal resolution. Configuration
options: [Disabled] [Enabled]
Legacy OS Redirection Resolution [80x24]
This allows you to set the number of rows and columns supported on the Legacy OS.
Configuration options: [80x24] [80x25]
Putty Keypad [VT100]
This allows you to select the FunctionKey and Keypad on Putty. Configuration options:
[VT100] [LINUX] [XTERMR6] [SCO] [ESCN] [VT400]
Redirection After BIOS POST [Bootloader]
This setting allows you to specify if Bootloader is selected than Legacy console
redirection. Configuration options: [Always Enable] [Bootloader]
Serial Port for Out-of-Band Management/Windows Emergency Management
Services (EMS) Settings
The following items only appears when you set the Console Redirection to [Enabled].
Out-of-Band Mgmt Port [COM1]
Allows remote management of a Windows Server OS through a serial port.
Configuration options: [COM1] [COM2]
Terminal Type [VT-UTF8]
Allows you to set the terminal type for out-of-band management. Configuration options:
[VT100] ASCII char set.
[VT100+] Extends VT100 to support color, function keys, et.
[VT-UTF8] Uses UTF8 encoding to map Unicode chars onto 1 or more bytes
[ANSI] Extended ASCII char set
Bits per second [115200]
Selects serial port transmission speed. The speed must be matched on the other side.
Long or noisy lines may require lower speeds. Configuration options: [9600] [19200]
[38400] [57600] [115200]
Flow Control [None]
Allows you to set the flow control to prevent data loss from buffer overflow.
Configuration options: [None] [Hardware RTS/CTS] [Software Xon/Xoff]