QS SERIE REMOTE CONTROL ENGINE STARTER USER MANUAL Model QS-2W For all automatic transmission gas- and diesel-powered vehicles. CONSULT SAFETY PRECAUTION SECTION BEFORE USING THIS PRODUCT. NEVER INSTALL THIS PRODUCT ON A MANUAL TRANSMISSION VEHICLE. SOME FEATURES MAY REQUIRE ADDITIONAL MATERIAL (NOT INCLUDED). (FRANÇAIS AU VERSO) PATENT NOS CAN 1.130.426 USA 4.345.554 - 5.614.883 - 5.617.819 - 5.673.
QS-2W GOVERNMENT REGULATIONS This device complies with the requirements of Industry Canada (IC) - Management of Radiofrequencies, as specified in document CNR-210. Its use is authorized only on a no-interference, no-protection basis; in other words, this device must not be used if it is determined that it causes harmful interference to services authorized by IC.
QS-2W THANK YOU FOR CHOOSING A PRIVATE LABEL “QS SERIE” REMOTE CAR STARTER! Like you, we are concerned with the environment. This is why we are suggesting you to use the two-minute runtime when you remote-start your vehicle to warm up engine fluids. We take this opportunity to remind you to properly defrost your windows and remove all the snow on your vehicle before driving on public roads.
QS-2W SAFETY PRECAUTIONS Before using this product, carefully read the following safety precautions. • Immediately report any malfunction to the authorized dealer that performed installation. • Under no circumstance can this product or its use be modified. • Always turn off main switch when vehicle is parked in an enclosed, unventilated area or is in for servicing. • Always turn off main switch when not using your Remote Starter for extended periods of time. • Keep remote controls away from children.
QS-2W THE REMOTE CONTROL Your remote control has been designed to fit the natural contours of your hand so that it is easier to use. It works off one regular AAA battery. Up to three additional remote controls can be assigned to your vehicle. See your dealer for replacement batteries or additional remote controls. NOTE: The range of your remote control can be affected by a weak battery, interference from nearby metal structures, hydro poles, or crowded parking lots.
QS-2W TABLE OF COMMANDS COMMANDS CONFIRMATIONS BUTTONS VEHICLE REMOTE CONTROL LIGHTS SOUND 1y 1 MELODY 3 (HIGH) DISPLAY AB - VIBRATION 2 2 STOP - 1 - A 2 LOCK 1♥ 1 1 C - UNLOCK - 2 2 D - TRUNK - 3 1 (HIGH) E - - 4/2/3 w - - 1 - 1 - - 1 RUNTIME - 1-4 - - 1 CAR FINDER 7 3 - - 1 STATUS - - - HORN START / CONTINUOUS MODE ACTIVATE / CANCEL LOW TEMPERATURE MODE ACTIVATE / CANCEL UTILITY OUT OF RANGE 1 2 ABCDE - y.
QS-2W CONFIRMATIONS Sent by vehicle Confirmations sent by the vehicle are generated as soon as command is received by starter module. Your remote starter will always confirm that the command has been received, either by sounding the horn or by flashing the parking lights. Parking light confirmation is mandatory while horn confirmation is optional (programmable) and requires an additional connection and equipment during installation.
QS-2W UPON ENTERING YOUR VEHICLE... Do not apply brakes; this will stop engine immediately. Insert ignition key and turn it to ON position. DO NOT TURN IGNITION KEY TO START POSITION. Drive as usual. STATUS When this command is sent, command module checks engine status (running or not) and lock status, then retransmits this information to remote control which indicates the results on the LCD display with a combination of pictograms.
QS-2W WHAT STOPS THE ENGINE For your safety, engine will not start or will stop if: Remote control sends a Stop message. Hood is open. Brakes are applied. Engine is over-revving. Main switch is OFF. MAIN SWITCH Main switch is usually mounted under dashboard. It is a toggle ON/OFF switch that is used to cancel start functions. It does not disable other commands which remain active. STOP When engine is running on a remote start, you can turn it off by pressing simultaneously.
QS-2W SETTING RUNTIME Press and buttons simultaneously (parking lights: 1 - 4). Parking lights flash one to four times to indicate selected runtime (see table opposite). If you send this command while ignition circuits are activated (by remote or key), runtime does not change but confirmation is sent to indicate last selection. If Low Temperature (Sentinel) mode is already activated when this command is sent, command sets or indicates Low Temperature mode runtime.
QS-2W TRUNK RELEASE Press and buttons simultaneously. Trunk releases and parking lights flash three times to confirm command has been received. Trunk cannot be released if key is in ON position. In this case, lights flash once to confirm command has been received and that trunk could not be released. If you are not sure you received a confirmation, repeat command. The system will repeat the confirmation as often as you wish.
QS-2W VALET MODE Valet mode allows you to disarm Antitheft system whenever your vehicle is left with someone else, for servicing for example. TO ACTIVATE VALET MODE, turn key to ON position then press Valet switch until antitheft status indicator stops flashing (approximately 3 seconds). TO DEACTIVATE VALET MODE, turn key to ON position then press and hold Valet switch for at least 3 seconds. To confirm Valet deactivation, send Lock command and check that antitheft status indicator starts flashing.
QS-2W SAFETY CHECKS In order to maintain a high safety standard, proceed with the following checks every month. HOOD SWITCH • Remote start your vehicle. • Open hood. Engine should stop as soon as hood is opened. If engine does not stop immediately, turn main switch to OFF position and leave it off until situation is rectified. Contact your service center. GEARSHIFT CHECK If key must be in ignition for gearshift to be moved out of P, your vehicle is safe as long as keys are kept away from children.
QS-2W Notes: 12
