Instruction manual
Table Of Contents
- 表紙英語版.pdf
- 中表紙英語版.pdf
- 納品_D0066取扱説明書_第1版(WM-3014).pdf
- INTRODUCTION
- SAFETY PRECAUTIONS
- Concerning the monitor
- ( Do not subject the monitor to strong impact or throw it around. Doing so may cause the liquid crystal to leak and/or the monitor to malfunction, rupture, generate heat and/or cau
- ( Do not use the monitor wherever there is a risk of ignition or explosions.
- ( Do not place the monitor inside a microwave oven or other heating or cooking appliance or pressure vessel. Doing so may cause heat or smoke to be generated in the monitor, combus
- ( Inside the monitor are some high-voltage parts: since exposure to these parts may result in electric shocks or burns and/or malfunctioning, refrain from disassembling, repairing
- ( If a thunderstorm should occur while the monitor is being used outdoors, immediately turn off its power, disconnect the power cable from the main unit, and move the monitor to a
- Concerning the power cord
- Concerning foreign matter
- Concerning the power supply
- ( Use a supply voltage within the range of DC 10V to 18V (5% for the monitor.
- ( In order to avoid malfunctioning and trouble, it is recommended that the accessory AC/DC adapter be used. In the event that another power supply is to be used, ensure that its su
- ( Do not turn the power back on immediately after having turned it off. Doing so can cause malfunctioning.
- ( Bear in mind that if the same DC power supply as microphones, amplifiers, speakers and other audio products should be used for the monitor, the sound may be adversely affected.
- Concerning the liquid crystal
- ( Due to the nature of liquid crystal, some picture elements may be missing (bright spots, flashing spots, etc.) at times.
- ( Do not touch any liquid crystal which has leaked from the liquid crystal panel.
- ( In the event that liquid crystal has made contact with your eyes or mouth, rinse it off with water immediately. If it has come into contact with your skin or clothing, wipe it of
- ( Exercise care with the glass of a broken liquid crystal panel.
- ( The LCD panel is a high-precision component and, as such, the following care must be taken in its handling.
- ( Handle the liquid crystal protective panel carefully.
- Concerning impact
- Concerning the installation and operation locations
- Concerning problems due to the nature of liquid crystal
- ( The liquid crystal's response time, brightness and colors may vary depending on the ambient temperature.
- ( Depending on what is displayed, unevenness in the brightness, flicker, vertical stripes and/or very small flecks may appear.
- ( The optical characteristics of liquid crystal (such as unevenness in the brightness or display) change in accordance with the operating time. These changes are particularly appar
- ( The display colors may change depending on the view angle.
- ( Noise may appear on the startup screen.
- ( Image lag may occur. Avoid displaying the same pattern for a prolonged period of time.
- Concerning the monitor
- 1
- CONCERNING THE WM-3014
- Outline of WM-3014
- ( 6.3-inch a-Si TFT LCD panel featured
- ( HD-SDI, SD-SDI or YPbPr HD analog signals supported as the input
- ( 25 different video formats supported
- ( SDI IN ((2), SDI MONITOR OUT, HD analog input (ANALOG Y, ANALOG Pb, ANALOG Pr) and composite input (NTSC, PAL) connectors provided
- ( Image adjustment functions
- ( Marker displays
- ( Single-action operation for selecting input channels, partial display/non-display of information, picture overlay and freeze/update using the switches on the front panel
- ( Many different display modes available
- ( Compare mode provided
- ( Lighting of red, green LEDs at top of screen using external control (contact supply type)
- ( Loading of preset data enabled by external control (contact supply type)
- ( Preset switches provided on front panel (for loading and saving the preset data)
- ( Automatic tracking of input signals supported
- ( Automatic 1/1.000 and 1/1.001 frame rate tracking and input signal detection functions
- ( Reference input (HD analog tri-level sync, BB_525, BB_625)
- ( CRC error detection function (during HD-SDI input) for input channels
- ( Time code (VITC) display (during HD-SDI input)
- ( Functions for locking the panel switches and storing the settings
- ( Light weight and slim-line dimensions
- ( DC 12V supported (10-18V)
- ( Camera battery supported
- ( 6.3-inch a-Si TFT LCD panel featured
- Outline of WM-3014
- 2
- PARTS AND THEIR FUNCTIONS
- 3
- OPERATION
- 4
- MAIN SPECIFICATIONS
- 5
- STANDARD AND OPTIONAL ACCESSORIES
- 6
- MAINTENANCE AND OTHER PROCEDURES
1
1
1
CONCERNING THE WM-3014
The WM-3014 is a compact, lightweight and portable LCD waveform monitor which comes in handy for monitoring the
pictures being shot during live broadcasts, on location or in studios.
The camera battery is supported as the power supply so that pictures, waveforms and sound can now be monitored
even in locations where it would be difficult to carry in equipment.
A full range of functions is provided including functions for adjusting the brightness, contrast and chroma levels as well
as functions for displaying markers.
Input signals in a total of 23 HDTV and two SDTV video formats as well as NTSC and PAL composite input signals are
supported. In regard to the PAL signals, however, the waveforms of the 3 lines each at the start and end of the video
signals will be more disturbed than in actuality.
Outline of WM-3014
6.3-inch a-Si TFT LCD panel featured
HD-SDI, SD-SDI or YPbPr HD analog signals supported as the input
25 different video formats supported
Standards complied with by HD-SDI signals: SMPTE 292M, BTA S-004B standards
(1.485 Gbps SDI input)
Standards complied with by SD-SDI signals: SMPTE 259M standard (270 Mbps SDI input)
Standards complied with by analog input and supported formats:
SMPTE 274M, SMPTE 296M, BTA S-001B standards
Composite input (NTSC: SMPTE 170M, PAL: ITU-R.BT624-4 complied with in part)
SDI IN (×2), SDI MONITOR OUT, HD analog input (ANALOG Y, ANALOG Pb,
ANALOG Pr) and composite input (NTSC, PAL) connectors provided
* When composite signals are input, the waveforms displayed are the waveforms which appear after the
component signal conversion. In regard to the PAL signals, however, the waveforms of the 3 lines each at
the start and end of the video signals will be more disturbed than in actuality.
Image adjustment functions
Brightness adjustment function (brightness can be adjusted separately for G, B and R) ±50%
Contrast adjustment function (contrast can be adjusted separately for G, B and R) 0 to 200%
Chroma level adjustment function 0 to 200%
Chroma boosting function
Separate ON/OFF functions for G, B and R
Peak function
Chroma signal OFF function
Gamma adjustment function (gamma can be adjusted separately for G, B and R)
Marker displays
Center marker, frame marker, safety markers (95%, 93%, 88%, 80%)
Markers for down-conversion (4:3, 13:9, 14:9)
Markers for cinema formats (2.35:1 Cinemascope, 1.85:1 Cinema Vista, 1.66:1 Euro Vista)
User variable markers