Specifications

8
./4%$)!'2!-3),,5342!4)/.3!2%./44/3#!,%
)../6!4)6%(%!24(02/$5#43s$)2%#46%.4'!3&)2%0,!#%3-ONTEBELLO$,8-ONTEBELLO$,8#$s).34!,,!4)/.).3425#4)/.3
*NOTE: 3" (75 mm) above any horizontal/inclined vent component.
**NOTE: See Page 9, Step 1 for clearance requirements to the nailing
flange located at each side of the unit and any screw heads adjacent
to it. See Page 28 for hearth extension requirements.
Shelf Height
4OPROVIDEFORTHELOWESTPOSSIBLESHELFSURFACETHEVENTINGATTACHEDTO
THETOPVENTSHOULDBEROUTEDINAWAYTOMINIMIZEOBSTRUCTIONSTOTHE
SPACEABOVETHEAPPLIANCEDo not insulate the space between the ap-
pliance and the area above itSEEFigure 7). The minimum height from
THEBASEOFTHEAPPLIANCETOTHEUNDERSIDEOFCOMBUSTIBLEMATERIALSUSED
to construct a utility shelf in this fashion is shown in Figure 7.
Wall Finishes / Surrounds / Mantels
NOTE: Combustible wall finish materials and/or surround materials must
not be allowed to encroach the area defined by the appliance front face
(black sheet metal). Never allow combustible materials to be positioned
in front of or overlapping the appliance face. See Figure 9 and Figure
51 on Page 28.
.ONCOMBUSTIBLEMATERIALSSUCHASSURROUNDSANDOTHERAPPLIANCETRIM
MAYBEINSTALLEDONTHEAPPLIANCEFRONTFACEWITHTHESEEXCEPTIONSTHEY
MUSTNOTCOVERANYPORTIONOFTHEREMOVABLEGLASSPANEL
6ERTICALINSTALLATIONCLEARANCESTOCOMBUSTIBLEMANTELSVARYACCORDING
to the depth of the mantel. See Figure 8-ANTELSCONSTRUCTEDOFNON
COMBUSTIBLEMATERIALSMAYBEINSTALLEDATANYHEIGHTABOVETHEAPPLIANCE
OPENING-INIMUMCLEARANCEREQUIREMENTSINCLUDEANYPROJECTIONSSUCH
ASSHELVESWINDOWSILLSMANTELSETCABOVETHEAPPLIANCE
NOTE: We recommend the use of high temperature paint (rated 175° F
or higher) on the underside of the mantel.
MINIMUM CLEARANCES TO COMBUSTIBLES
4HEAPPLIANCEISAPPROVEDWITHZEROCLEARANCETOCOMBUSTIBLEMATERIALS
ONALLSIDESASDETAILEDINTable 5)WITHTHEFOLLOWINGEXCEPTIONWhen
the unit is installed with one side flush with a wall, the wall on the
other side of the unit must not extend beyond the front edge of the
unit. In addition, when the unit is recessed, the side walls surrounding
THEUNITMUSTNOTEXTENDBEYONDTHEFRONTEDGEOFTHEUNITSEEFigure 2).
Figure 9
17 in.
(432 mm)
14 in.
(356 mm)
8-1/4 in.
(210 mm)
45°
12 in.
(305 mm)
5 in.
(127 mm)
12 (305)
10 (254)
8 (203)
6 (152)
4 (102)
7
(178)
17
(432)
15
(381)
13
(330)
2 (51)
9
(229)
11
(279)
Figure 8
Combustible Materials
Allowed In Shaded Area
"Safe Zone"
Top View of
Fireplace
Minimum Distance to
Protected Side Wall
Minimum Distance to
Unprotected Side Wall
Side
Wall
Side
Wall
MANTEL
CLEARANCES
Inches (mm)
Top of Appliance
MANTEL
MANTEL
MANTEL
MANTEL
MANTEL
MANTEL
Fireplace
(side view)
Figure 7
APPLIANCE MINIMUM CLEARANCES*
Inches (millimeters)
Sides 1/2 (13), 0 (0) Spacers **
Top Spacers 0 (0)
Floor 0 (0)
Back 1/2 (13), 0 (0) Spacers
Bottom of Appliance To Ceiling 69 (1743)
Vent 3 (76)
Top* / 1 (25.4) Sides & Bottom
SERVICE CLEARANCES Feet (meters)
Front 3 feet (0.9 meters)
Table 5
Combustible Shelf Height—Inches (millimeters)
Top Vent—with 2 Feet Vertical Vent and One 90 Degree Elbow
Model Secure Vent
®
40 in. *84-1/16 (2135)
45 in. *89-1/16 (2252)
* Includes 3" clearance to combustibles (required above vent components)
Do not insulate the
space between the
appliance and the
area above it.
2-1/2 ft
(to centerline)
Vertical
Vent (minimum)
Shelf Height
(see table)
Shelf Above Fireplace With Top Venting