Specifications

./4%$)!'2!-3),,5342!4)/.3!2%./44/3#!,%
5
)../6!4)6%(%!24(02/$5#43s$)2%#46%.4'!3&)2%0,!#%3-ONTEBELLO$,8-ONTEBELLO$,8#$s).34!,,!4)/.).3425#4)/.3
LOCATION
In selecting the location, the aesthetic and
functional use of the appliance are primary
concerns. However, vent system routing to
THEEXTERIORANDACCESSTOTHEFUELSUPPLYARE
also important.
Due to high temperatures, the appliance
should be located out of traffic and away from
furniture and draperies (Figure 2).
En raison des températures élevées,
l’appareil devrait être installé dans un
endroit où il y a peu de circulation et loin
du mobilier et des tentures (Figure 2).
4HELOCATIONSHOULDALSOBEFREEOFELECTRICAL
PLUMBING OR OTHER HEATINGAIR CONDITIONING
ducting.
4HESE DIRECTVENT APPLIANCES ARE UNIQUELY
SUITEDFORINSTALLATIONSREQUIRINGAUTILITYSHELF
POSITIONEDDIRECTLYABOVETHElREPLACE5TILITY
SHELVES LIKE THESE ARE COMMONLY USED FOR
locating television sets and decorative plants.
Drywall
T op Of Firepl
ace
Opening
Non-Combus
tible
Figure 2—Typical Installation
When the unit is installed with one side flush with
a wall, the wall on the other side of the unit must
not extend beyond the front edge of the unit.
HORIZONTAL VENT
VERTICAL VENT
HORIZONTAL VENT
VERTICAL VENT
CROSS CORNER
APPLICA
TION
RECESSED
APPLICATION
FLA
T
APPLICA
TION
ROOM DIVIDER
APPLICA
TION
FLA
T ON W
ALL
APPLICA
TION
ISLAND
APPLICA
TION
COLD CLIMATE INSULATION
&ORCOLDCLIMATEINSTALLATIONSSEAL ALLCRACKS
AROUND YOUR APPLIANCE WITH NONCOMBUSTIBLE
material and wherever cold air could enter
the room. It is especially important to insulate
OUTSIDECHASECAVITYBETWEENSTUDSANDUNDER
mOORONWHICHAPPLIANCERESTSIFmOORISABOVE
GROUNDLEVEL'ASLINEHOLESANDOTHEROPENINGS
SHOULD BE CAULKED OR STUFFED WITH UNFACED
lBERGLASSINSULATION
)FTHElREPLACEISBEINGINSTALLEDONACEMENT
SLABINCOLDCLIMATESASHEETOFPLYWOODOR
OTHERRAISEDPLATFORMCANBEPLACEDUNDERNEATH
TOPREVENT COLD TRANSFER TO THE lREPLACE AND
INTOTHEROOM)TALSOHELPSTOSHEETROCKINSIDE
SURFACESANDTAPEFORMAXIMUMAIRTIGHTNESS
ANDCAULKlRESTOPS
MANUFACTURED HOME REQUIREMENTS
4HISAPPLIANCEMAYBEINSTALLEDINANAFTERMARKET
permanently located, manufactured home and
MUSTBEINSTALLEDINACCORDANCEWITHTHEMANU-
FACTURERgSINSTRUCTIONSANDTHE-ANUFACTURED
Home Construction and Safety Standard, Title
#&20ARTINTHE5NITED3TATESORTHE
3TANDARDFOR)NSTALLATIONIN-OBILE(OMES#!.
#3!:-(3ERIESIN#ANADA
Cet appareil peut être installé cómme
du matéri-el d'origine dans une maison
PR£FABRIQU£E »5 SEULEMENT OU MOBILE
et doit être installé selon les instructions
DUFABRICANTETCONFORM£MENTÜLANORME
-ANUFACTURED (OME #ONSTRUCTIONS AND
3AFETY4ITLE#&2 0ART AUX 5NIS
OU Ü LA NORME #AN#3!: 3£RIE --
-AISONSMOBILESAU#ANADA
This appliance is only for use with the type of
gas indicated on the rating plate. This appliance
ISNOTCONVERTIBLEFORUSEWITHOTHERGASESUN-
LESSACERTIlEDKITISUSED
#ET APPAREIL DOIT äTRE UTILIS£ UNIQUEMENT
AVECLETYPEDEGAZINDIQU£SURLAPLAQUE
SIGNAL£TIQUE#ETAPPAREILNEPEUTäTRECON-
VERTIÜDgAUTRESGAZSAUFSIUNETROUSSEDE
conversion est utilisée.
CAUTION: Ensure that the cross members
are not cut or weakened during installa-
tion. The structural integrity of the manu-
factured home floor, wall, and ceiling / roof
must be maintained.
CAUTION: This appliance must be ground-
ed to the chassis of the manufactured
home in accordance with local codes or
in the absence of local codes, with the
National Electrical Code ANSI / NFPA 70—
latest edition or the Canadian Electrical
Code CSA C22.1—latest edition.
Be aware that this is a heat producing ap-
pliance. Objects placed above the unit are
exposed to elevated temperatures.
Do not insulate the space between the
appliance and the area above itsee Figure
7 on Page 8).
4HE MINIMUM HEIGHT FROM THE BASE OF THE
APPLIANCE TO THE UNDERSIDE OF COMBUSTIBLE
materials used to construct a utility shelf in
this fashion is shown in Figure 7 on Page 8.
4HE APPLIANCE MUST BE MOUNTED ON A FULLY
SUPPORTED BASE EXTENDING THE FULL WIDTH
ANDDEPTHOFTHEUNIT4HEAPPLIANCEMAYBE
located on or near conventional construction
MATERIALS(OWEVERIFINSTALLEDONCOMBUSTIBLE
materials, such as carpeting, vinyl tile, or other
COMBUSTIBLEMATERIALOTHERTHANWOODmOORING
THEAPPLIANCESHALLBEINSTALLEDONAMETALOR
WOODPANELEXTENDINGTHEFULLWIDTHANDDEPTH
of the appliance.
Recessed
Application
Cross Corner
Application
Flat
Application
Flat on Wall
Application
Room Divider
Application
Island
Application