Specifications

./4%$)!'2!-3),,5342!4)/.3!2%./44/3#!,%
23
)../6!4)6%(%!24(02/$5#43s$)2%#46%.4'!3&)2%0,!#%3-ONTEBELLO$,8-ONTEBELLO$,8#$s).34!,,!4)/.).3425#4)/.3
WARNING
Never use an open flame to
check for leaks.
4URNONGASSUPPLYANDTESTFORGASLEAKSUSINGA
GASLEAKTESTSOLUTIONALSOREFERREDTOASBUBBLE
LEAKSOLUTION
NOTE: Using a soapy water solution is an
effective leak test solution but it is not recom-
mended, because the soap residue that is left
on the pipes/fittings can result in corrosion
over time.
Step 5. REMOVE GLASS DOOR FRAME
2EMOVETHEGLASSDOORASSEMBLY3EEInstalla-
tion and Removal of Glass Door on Page 26.
Step 6. CONNECTING GAS LINE
!LLCODESREQUIREASHUTOFFVALVEMOUNTEDINTHE
supply line. The orientation of the shut-off valve
should face the front. Figure 36 illustrates two
methods for connecting the gas supply. A Sedi-
ment Trap is recommended to prevent moisture
ANDDEBRISINGASLINEFROMDAMAGINGTHEVALVE
4HEmEXLINEMETHODISACCEPTABLEINTHE53!
where local codes permit, however, Canadian
REQUIREMENTSVARYDEPENDINGONLOCALITY)NSTAL-
LATIONMUSTBEINCOMPLIANCEWITHLOCALCODES
4HESEAPPLIANCESAREEQUIPPEDWITHAGASmEX
line for use in connecting the unit to the gas
line. See Figure 36 FORmEXLINEDESCRIPTION4HE
mEXLINEISRATEDFORBOTHNATURALANDPROPANE
gas. A manual shut off valve is also provided
WITHTHEmEXLINE
The gas control valve is located on the right
side of the unit.
7HENUSINGSOLIDGASLINECONNECTORACCESS
THEVALVEBYREMOVINGTHEFRONTDOORASSEMBLY
on the valve access side and the access plate
see Figure 37).
4HEELECTRONICCONTROLVALVEHASAMM
NPT thread gas supply inlet.
"RINGTHESHUTOFFVALVEONTHEENDOFTHEmEXLINE
over to the hard pipe and tighten with wrenches
FROMABOVETHROUGHTHElREBOXOPENING
Secure all joints tightly using appropriate
tools and sealing compounds (ensure propane
resistant compounds are used in propane ap-
plications). It is recommended to seal around
the gas line to prevent cold air leakage.
Figure 38
Gas Valve
Access Plate
Right Side
Modesty Panel
Figure 37
NOTE: The gas supply line must
be installed in accordance
with building codes by a quali-
fied installer approved and/or
licensed as required by the
locality. In the Commonwealth
of Massachusetts, installation
must be performed by a licensed
plumber or gas fitter.
Gas
Valve
3/8" NPT x
Flare Fitting
3/8" Flex Tubing
3/8" Nipple
3/8" Union
3/8" Close
Nipple
3/8" Shut-off Valve
1/2" x 3/8"
Reducer
Gas
Stub
1/2" x 3/8" Flare
Shut-off Valve
Gas Solid Line Connector
Gas Flex Line Connector
*Sediment
Trap
3"
Min
Figure 36—Gas Connection
A.,IGHT THE APPLIANCE REFER TO THE LIGHTING
INSTRUCTIONSLABELINTHECONTROLCOMPARTMENT
or in the Care and Operation Instructions
MANUAL
B. "RUSHALLJOINTSANDCONNECTIONSWITHTHEGAS
LEAKTESTSOLUTIONTOCHECKFORLEAKS)FBUBBLES
are formed, or gas odor is detected, turn the
RECEIVERORREMOTECONTROLTOTHEh/&&vPOSITION
%ITHERTIGHTENORREFASTENTHELEAKINGCONNECTION
THENRETESTASDESCRIBEDABOVE
C. 7HENTHEGASLINESARETESTEDANDLEAKFREE
BESURETORINSEOFFTHELEAKTESTINGSOLUTION
D. 2EINSTALLTHEACCESSPLATEMAKINGCERTAINTHE
GASKETHASNOTBEENDAMAGED
Step 7. CHECKING APPLIANCE
OPERATION
4URN ON BURNER THEN OBSERVE THE INDIVIDUAL
TONGUESOFmAMEONTHEBURNER-AKESUREALL
ports are open and producing flame evenly
ACROSSTHEBURNER)FANYPORTSAREBLOCKEDOR
PARTIALLYBLOCKEDCLEANOUTTHEPORTS
7ITHGASLINEINSTALLEDRUNINITIALSYSTEMCHECK-
OUTBEFORECLOSINGUPTHEFRONTOFTHEUNIT&OLLOW
the lighting instructions provided in the Care
and Operation Instructions manual.
NOTE: Lighting Instructions are also found on
the literature tag tied to the bracket above the
gas valve. To access the tag, reach into the
right side opening.
7HENlRSTLIGHTINGTHEAPPLIANCEITWILLTAKEAFEW
minutes for the line to purge itself of air. Once
PURGINGISCOMPLETETHEPILOTANDBURNERWILL
light and operate as indicated in the instruction
MANUAL3UBSEQUENTLIGHTINGOFTHEAPPLIANCEWILL
NOTREQUIRESUCHPURGING)NSPECTTHEPILOTmAME
REMOVELOGSIFNECESSARYHANDLINGCAREFULLY
Electronic Appliance Checkout
4OLIGHTTHEBURNERTURNh/.vTHEOPTIONALREMOTE
wall switch or turn the appliance mounted ON/
/&&SWITCHTOTHEh/.vPOSITION%NSURETHE
igniter lights the pilot. The pilot flame should
engulf the flame sensor as shown in Figure 38.
TEST ALL CONNECTIONS FOR GAS LEAKS
(FACTORY AND FIELD):
Pilot
Hood
Flame Rod
(Sensor)
Igniter