Specifications

22
./4%$)!'2!-3),,5342!4)/.3!2%./44/3#!,%
)../6!4)6%(%!24(02/$5#43s$)2%#46%.4'!3&)2%0,!#%3-ONTEBELLO$,8-ONTEBELLO$,8#$s).34!,,!4)/.).3425#4)/.3
Installing and initializing the Remote
Control System
REQUIRED ITEMS (not provided):
s3TANDARD*UNCTION"OX
s0APER#LIPORSIMILAROBJECTFORREMOTE
CONTROLSYSTEMINITIALIZATION
Installing and Wiring the Receiver
(Wall Switch)
The receiver for the Total Comfort Control™
Remote Control System connects directly to
the gas valve, stepper motor, and fan control
MODULEWITHANUMBILICALCORDWIRINGHARNESS
 )NSTALLAJUNCTIONBOXNOTPROVIDEDON
THEWALLADJACENTTOTHEAPPLIANCEWITHIN
REACHOFTHEREMOTESYSTEMUMBILICALCORD
wiring harness. Position the 6-pin termi-
NALWITHINTHEJUNCTIONBOXINPREPARATION
for attachment to the remote receiver.
 7HENWALLlNISHISCOMPLETEINSTALLTHE
RECEIVERINTHEPREVIOUSLYINSTALLEDJUNC-
TIONBOXANDCONNECTTHEPINTERMINAL
TOTHEPINCONNECTORONTHEBACKOFTHE
receiver.
 )NSTALLTHERECEIVERCOVERPLATETAKINGCARE
to ensure the receiver switch is properly
INDEXEDWITHTHESWITCHCOVERWHENALIGN-
ing the components for attachments.
Initializing the Remote Control System
!FTERCOMPLETINGlREPLACEINSTALLATIONINITIALIZE
THE REMOTE CONTROL SYSTEM BEFORE OPERATING
THElREPLACE
 )NSERTTHETHREEPROVIDED!!!BATTERIES
INTOTHEBATTERYBAYINTHETRANSMITTERTAK-
INGCARETOCORRECTLYALIGNPOLARITY
+

 )NSERTTHEFOURPROVIDED!!BATTERIES
INTOTHERECEIVERBATTERYBAYBEHINDTHE
WALLSWITCHPLATETAKINGCARETOCORRECTLY
ALIGNPOLARITY
+

6. On the receiver, place the three-position
SLIDER SWITCH IN THE 2%-/4% POSITION
(Figure 34).
 /NTHERECEIVERFRONTCOVERINSERTTHEEND
OFAPAPERCLIPOROTHERSIMILAROBJECTNOT
PROVIDEDINTOTHEHOLEMARKEDh02'v
 4HE RECEIVER WILL hBEEPv THREE TIMES TO
indicate it is ready to synchronize with
the transmitter.
 /NTHETRANSMITTERPRESSTHE/.BUTTON
4HE RECEIVER WILL hBEEPv FOUR TIMES TO
INDICATE ACCEPTANCE OF THE TRANSMITTERS
COMMAND AND SET THE RECEIVER TO THE
TRANSMITTERSSPECIlCCODE4HESYSTEM
is now initialized.
WARNING
Fire hazard. Can cause severe
injury or death. The receiver
causes ignition of the appliance.
The appliance can turn on
suddenly. Keep away from
the appliance burner when
operating the remote system or
activating manual bypass of the
remote system.
CAUTION
Property damage hazard. Exces-
sive heat can cause property
damage. The appliance can stay
lit for many hours. Turn off the
appliance if it is not going to be
attended for any length of time.
Always place the transmitter
where children can not reach it.
Figure 34—Receiver (Wall Switch)
Remote
Off
On
PRG
Three-position slider switch
in REMOTE position
Figure 35—Transmitter (Remote Control)
Hot Fireplace Will Cause
Severe Burns
Never Allow Children to
Touch Glass or other Fire-
place Parts
W
ARNING
LCD Display
ON/OFF Key
ROOM
TEMP.
Key
UP/DOWN
Arrow Key
MODE Key
The remote control system provides remote
OPERATIONOFTHEFOLLOWINGlREPLACEFUNCTIONS
s0RIMARYBURNER/./&&
s&LAMEHEIGHTANDHEATOUTPUTADJUSTMENT
SIXLEVELS
The receiver accepts commands via radio
FREQUENCYFROMTHETRANSMITTERANDDOESNOT
REQUIRELINEOFSIGHTOPERATION
4HESLIDERSWITCHONTHERECEIVERCANBESETTO
one of three positions:
s/.MANUALOVERRIDE
s/&&MANUALOVERRIDE
s2%-/4%REMOTECONTROL
3EETHElREPLACE#AREAND/PERATION)NSTRUC-
tions for detailed instructions on using the
REMOTECONTROLSYSTEMTOOPERATETHElREPLACE