Specifications

./4%$)!'2!-3),,5342!4)/.3!2%./44/3#!,%
15
)../6!4)6%(%!24(02/$5#43s$)2%#46%.4'!3&)2%0,!#%3-ONTEBELLO$,8-ONTEBELLO$,8#$s).34!,,!4)/.).3425#4)/.3
Framing Dimensions for Roof
Inches (millimeters)
Pitch C D
0/12
13"
(330 mm)
13"
(330 mm)
6/12
13"
(330 mm)
15-1/2"
(394 mm)
12/12
13"
(330 mm)
20-1/2"
(541 mm)
C
D
Figure 20—Roof Framing
Figure 22
G. Continue installation of horizontal/inclined
sections—Continue with the installation of the
straight vent sections in horizontal/inclined run
ASDESCRIBEDINStep C. Install support straps
EVERYFTMMALONGHORIZONTALINCLINED
VENTRUNSUSINGCONVENTIONALPLUMBERSTAPE
See Page 17, Figure 26. It is very important
that the horizontal/inclined RUNBEMAINTAINEDIN
ASTRAIGHTNODIPSSLIGHTLYELEVATEDPLANE4HE
RECOMMENDEDINCLINEISAPPROXIMATELYPER
FOOTMMPERMETERHORIZONTALINADIRECTION
AWAYFROMTHElREPLACE4HERISEPERFOOTRUN
RATIOSTHATARESMALLERAREACCEPTABLEALLTHEWAY
DOWNTOATORNEARLEVEL5SEACARPENTERSLEVEL
TOMEASUREFROMACONSTANTSURFACEANDADJUST
the support straps as necessary.
It is important to maintain the required clear-
ances to combustibles: 1" (25 mm) at all sides
for all vertical runs; and 3" (76 mm) at the
top, 1" (25 mm) at sides, and 1" (25 mm) at
the bottom for all horizontal/inclined runs.
H. Frame roof opening—Identify location for
vent at the roof. Cut and/or frame opening per
2OOF&RAMING#HART(Figure 20).
/NEMETHODOFSUPPORTISBYUTILIZINGlELDPRO-
VIDEDSUPPORTSTRAPSCONVENTIONALPLUMBERgS
TAPE3ECURETHEPLUMBERgSTAPETOTHEFRAMING
MEMBERSWITHNAILSORSCREWS Strap the tape
around the vent, securing the ends of the tape
to the framing. If desired, sheet metal screws
XLENGTHMAY BE USED TOSECURETHE
support straps to the vent pipe. See Figure 18
on Page 14.
F. Change vent direction to horizontal/inclined
run—At transition from or to a horizontal/
INCLINEDRUNINSTALLTHE36%AND36%
ELBOWSINTHESAMEMANNERASTHESTRAIGHTVENT
SECTIONS4HEELBOWSFEATUREATWISTSECTIONTO
ALLOWTHEMTOBEROUTEDABOUTTHECENTERAXIS
of their initial collar section to align with the
REQUIREDDIRECTIONOFTHENEXTVENTRUNELEMENT
Twist elbow sections in a clockwise direction
only so as to avoid the possibility of unlocking
any of the previously connected vent sections.
See Figure 17 on Page 14 and Figure 19.
Figure 19
)FTHEVENTSYSTEMEXTENDSMORETHANFEET
MABOVETHEROOFmASHINGSTABILIZERSMAYBE
NECESSARY!DDITIONALSCREWSMAYBEUSEDAT
SECTIONJOINTSFORADDEDSTABILITY'UIDEWIRES
MAYBEATTACHEDTOTHEJOINTFORADDITIONALSUP-
PORTONMULTIPLEJOINTCONlGURATIONS
Swivel Joint
(360° swivel)
SV8E45
(45° Elbow)
Swivel Joint
(360° swivel)
SV8E90
(90° Elbow)
6"
(153mm)
10"
(254mm)
K. Install the vertical termination—4HElNAL
step involves installation of the Vertical Termina-
TION%XTENDTHEVENTSECTIONSTOTHEHEIGHTAS
SHOWNINTHE6ERTICALVENTTERMINATIONSECTION
on Page 64HE366426ERTICAL4ERMINATION
Figure 22)CANBEINSTALLEDINTHEEXACTSAME
fashion as any other Secure Vent
®
section. Align
the termination over the end of the previously
INSTALLEDSECTIONADJUSTINGTHERADIALALIGNMENT
UNTILTHEFOURLOCKINGDIMPLESOFTHETERMINATION
are aligned with the inlets of the four incline
channels of the last vent section. Push the ter-
mination down until it fully engages, then twist
THETERMINATIONCLOCKWISERUNNINGTHEDIMPLES
down and along the incline channels until they
seat at the end of the channels.
I. Install the roof flashing—%XTENDTHEVENT
sections through the roof structure. Install the
roof flashing over the vent section and posi-
tion such that the vent column rises vertically
USECARPENTERSLEVEL(Figure 21). Nail along
PERIMETERTOSECUREmASHINGORADJUSTROOlNGTO
overlap the flashing edges at top and sides only
ANDTRIMWHERENECESSARY3EALTHETOPANDBOTH
SIDESOFTHEmASHINGWITHWATERPROOFCAULKING
J. Install the storm collar—Install the storm
collar, supplied with the flashing, over the vent/
mASHINGJOINTSEEFigure 21). ,OOSENTHESTORM
collar screw. Slide collar down until it meets
THETOPOFTHEmASHING4IGHTENTHEADJUSTING
SCREW !PPLY NONCOMBUSTIBLE CAULKING OR
MASTICAROUNDTHECIRCUMFERENCEOFTHEJOINT
to provide a water tight seal.
Figure 21
Storm
Collar
Storm
Collar
Flashing