Specifications

./4%$)!'2!-3),,5342!4)/.3!2%./44/3#!,%
11
)../6!4)6%(%!24(02/$5#43s$)2%#46%.4'!3&)2%0,!#%3-ONTEBELLO$,8-ONTEBELLO$,8#$s).34!,,!4)/.).3425#4)/.3
Figure 12—Corner Framing with Square Termination (SV8HTS)
Proper Sizing of Gas Line
Properly size and route the gas supply
line from the supply regulator to the area
WHERE THE APPLIANCE IS TO BE INSTALLED PER
REQUIREMENTSOUTLINEDINTHE.ATIONAL&UEL'AS
#ODE.&0!LATESTEDITION53!OR#!.
#'!"LATESTEDITION#ANADA
NOTES:
s !LLAPPLIANCESAREFACTORYEQUIPPEDWITHA
mEXIBLEGASLINECONNECTORANDSHUTOFF
VALVESEEFigure 36 on Page 23).
s 3EEMassachusetts Requirements on Page
4FORADDITIONALREQUIREMENTSFORINSTALLATIONS
INTHESTATEOF-ASSACHUSETTSINTHE53!
s 4HEGASSUPPLYLINESHOULD.OTBECONNECTED
to the appliance until Step 6Page 23).
s !PIPEJOINTCOMPOUNDRATEDFORGASSHOULDBE
USEDONTHETHREADEDJOINTS Ensure propane
resistant compounds are used in propane
applications"EVERYCAREFULTHATTHEPIPE
compound does not get inside the pipe.
s )TISRECOMMENDEDTOINSTALLASEDIMENTTRAP
INTHESUPPLYLINEASCLOSEASPOSSIBLETOTHE
APPLIANCESEEFigure 36 on Page 23).
s #HECKWITHLOCALBUILDINGOFlCIALFORLOCAL
CODEREQUIREMENTS
IMPORTANT: If propane is used, be aware that
if tank size is too small (i.e. under 100 lbs, if
this is the only gas appliance in the dwelling.
Ref. NPFA 58), there may be loss of pressure,
resulting in insufficient fuel delivery (which
can result in sooting, severe delayed ignition
or other malfunctions). Any damage resulting
from an improper installation, such as this,
is not covered under the limited warranty.
Right Side
Front Corner
Of Fireplace
Framing
6-1/4”
(159 mm
)
19-5/8”
(498 mm
)
Step 2. ROUTING GAS LINE
2OUTEAMMGASLINEALONGTHEINSIDE
of the right side framing as shown in Figure
13'ASLINESMUSTBEROUTEDCONSTRUCTEDAND
made of materials that are in strict accordance
with local codes and regulations.
!LL APPLIANCES ARE FACTORYEQUIPPED WITH A
mEXIBLE GAS LINE CONNECTOR AND  SHUTOFF
valve. (See Step 6 on Page 22).
4HEINCOMINGGASLINESHOULDBEPIPEDINTOTHE
valve compartment and connected in one of the
two methods as shown in Figure 36 o n Page 23.
Never use galvanized or plastic pipe. Refer to
Table 6 for proper sizing of the gas supply
LINEIFBLACKIRONPIPEISBEINGUSED'ASLINES
MUST BE ROUTED CONSTRUCTED AND MADE OF
materials that are in strict accordance with
LOCALCODESANDREGULATIONS7ERECOMMEND
THATAQUALIlEDINDIVIDUALSUCHASAPLUMBER
ORGASlTTERBEHIREDTOCORRECTLYSIZEANDROUTE
the gas supply line to the appliance. Installing
a gas supply line from the fuel supply to the
appliance involves numerous considerations of
materials, protection, sizing, locations, controls,
pressure, sediment, and more. Certainly no one
UNFAMILIARANDUNQUALIlEDSHOULDATTEMPTSIZING
or installing gas piping.
Figure 13
Schedule 40—Black Iron Pipe
Inside Diameter (Inches)
Schedule 40 Pipe
Length (feet)
Natural
Gas
Propane
Gas
0–10  
10–40  
40–100  
100–150  
150–200  
Table 6
C
Back wall of chase/enclosure
(including any finishing materials)
D
A
B
Model
A B C D
40 in.
in. 50-5/8 83-5/8 59-1/8 41-7/8
mm 1286 2124 1502 1064
45 in.
in. 56-3/4 89-7/8 63-1/2 44-7/8
mm 1441 2283 1613 1140