INSTALLATION INSTRUCTIONS Montebello DLX 40 and 45 in. Direct Vent Gas Fireplaces Intertek Report No. 100513650 P/N 506023-22 Rev. NC 12/2013 This manual is one of a set of two supporting this product. Refer to P/N 506025-14 for Care and Operation Instructions. Ce manuel est disponible en francais, simplement en faire la demande. Numéro de la pièce 506023-23. INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 TABLE OF CONTENTS 0ACKAGING . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 'ENERAL )NFORMATION . . . . . . . . . . . . . . . . . . -ASSACHUSETTS 2EQUIREMENTS . . . . . . . . . . 4 Cold Climate Insulation . . . . . . . . . . . . . . . 5 -ANUFACTURED (OME 2EQUIREMENTS . . . . . . 5 ,OCATION . . . . . . . . . . . . . . . . .
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 GENERAL INFORMATION WARNING Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 These electronic appliances are remotely controlled and feature an electronic intermittent pilot ignition system or standing pilot. %XTERNAL ELECTRICAL POWER IS REQUIRED TO OPERATE these units.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 VENT TERMINATION CLEARANCES These instructions should be used as a guideline and do not supersede local codes in any way. Install vent according to local codes, these instructions, the current National Fuel Gas Code (ANSI-Z223.1) in the USA or the current standards of CAN/CGA-B149.1 in Canada.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 NOTE: Local Codes Or Regulations May Require Different Clearances. * See Item D in the Text Below. Center Line Exterior Wall of Termination Inside Corner Detail *18” 24" Horizontal Termination NOTE: Location Of The Vent Termination Must Not Interfere With Access To The Electrical Service. G 18” 36" V Ventilated Soffit A Inside Corner = 9" in U.S.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 MINIMUM CLEARANCES TO COMBUSTIBLES 4HE APPLIANCE IS APPROVED WITH ZERO CLEARANCE TO COMBUSTIBLE MATERIALS ON ALL SIDES AS DETAILED IN Table 5) WITH THE FOLLOWING EXCEPTION When the unit is installed with one side flush with a wall, the wall on the other side of the unit must not extend beyond the front edge of the unit.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 WARNING Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 Framing Dimensions Model 40 in. 45 in. A B C in. 50-3/4 43 75-1/8 mm 1289 1092 1908 in. 56-7/8 48 80-1/16 mm 1445 1219 2034 Framing should be constructed of 2x4 or larger lumber.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 Model 40 in. 45 in. A B C D in. 50-5/8 83-5/8 59-1/8 41-7/8 mm 1286 2124 1502 1064 in. 56-3/4 89-7/8 63-1/2 44-7/8 mm 1441 2283 1613 1140 C D A B Back wall of chase/enclosure (including any finishing materials) Figure 12—Corner Framing with Square Termination (SV8HTS) Step 2.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 Step 3. INSTALL THE VENT SYSTEM Installation of Vent Restrictor Select Venting System—Horizontal or Vertical General Information ! VENT RESTRICTOR MAY BE NEEDED WITH THIS appliance. The restrictor is installed in the appliance top flue outlet as shown in Figure 14, 7ITH THE APPLIANCE SECURED IN FRAMING DETERMINE VENT ROUTING AND IDENTIFY THE EXTERIOR termination location.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 VERTICAL TERMINATION SYSTEMS (ROOF) See Figure 15 and Figures 23 through 25 on Page 16 and their associated Vertical Vent 4ABLESWHICHILLUSTRATETHEVARIOUSVERTICALVENTING CONlGURATIONSTHATAREPOSSIBLEFORUSEWITHTHESE appliances.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 /NE METHOD OF SUPPORT IS BY UTILIZING lELD PROVIDED SUPPORT STRAPS CONVENTIONAL PLUMBERgS TAPE 3ECURE THE PLUMBERgS TAPE TO THE FRAMING MEMBERS WITH NAILS OR SCREWS Strap the tape around the vent, securing the ends of the tape to the framing. If desired, sheet metal screws X LENGTH MAY BE USED TO SECURE THE support straps to the vent pipe. See Figure 18 on Page 14. F.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 VERTICAL VENT FIGURES/TABLES NOTES: s 3ECURE 6ENT® (rigid vent pipe) is shown in the figures. s )T IS VERY IMPORTANT THAT THE HORIZONTAL inclined run be maintained in a straight (no dips), slightly elevated plane. The recommended incline is approximately 1/4" per foot (20 mm per meter) horizontal, in a direction away from the fireplace.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 J.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 See Table 9 as an aid in venting component selection for a particular range of exterior wall thicknesses.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 HORIZONTAL VENT FIGURES/TABLES (continued) Wall Firestop/Spacer (SV8HF) Table D H + H1 Maximum H H1 V Wall Firestop/Spacer (SV8HF) Ceiling Firestop/Spacer (SV8BF) V Minimum feet (meter) feet (meter) 3.5 (1.07) 2.5 (0.762) 6.5 (1.98) 3.5 (1.07) 8.5 (2.6) 4.5 (1.37) 10.5 (3.2) 5.5 (1.68) 12.5 (3.8) 6.5 (1.98) 14.5 (4.4) 7.5 (2.3) 16.5 (5.0) 8.5 (2.6) 18.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 Step 4. FIELD WIRING Verify proper operation after servicing. S’assurer que l’appareil fonctionne adéquatement une fois l’entretien terminé. CAUTION Ground supply lead must be connected to the wire attached to the green ground screw located on the outlet box. Failure to do so will result in a potential safety hazard.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 Step 5. REMOVE GLASS DOOR FRAME 2EMOVE THE GLASS DOOR ASSEMBLY 3EE Installation and Removal of Glass Door on Page 26. Step 6. CONNECTING GAS LINE A. ,IGHT THE APPLIANCE REFER TO THE LIGHTING INSTRUCTIONS LABEL IN THE CONTROL COMPARTMENT or in the Care and Operation Instructions MANUAL B.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 Step 8. INSTALL VOLCANIC STONE, GLOWING EMBERS, AND LOGS (Traditional Only), or GLASS MEDIA (Contemporary Only) NOTE: If installing the Contemporary Burner/Floor Kit, skip this step and instead refer to the instructions provided with the kit. Step 4. Position the individual logs as shown in Figures 42 through 46.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 Traditional Only: Log Placement 3 5 6 2 4 1 7 Log Number Description 1 ,OG #ENTER 2 ,OG 2EAR ,OG #ENTER ,EFT 4 ,OG #ENTER 2IGHT 5 ,OG 2EAR 4OP 6 ,OG &RONT ,EFT ,OG &RONT #ENTER 4 3 Engage Logs (3 & 4) With The Grate Pins And Align Groves At The Bottom Of The Logs Over The Grate.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 Step 9. INSTALLATION AND REMOVAL OF GLASS DOOR WARNING s When reinstalling the glass door, the door latch screws must be securely tightened to prevent the glass door from falling out, which could potentially cause damage and possible injury. s Do not attempt to substitute the materials used on this door, or replace cracked or broken glass.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 Burner Air Shutter Adjustment Procedure Air Shutter Opening WARNING s Air shutter adjustment should only be performed by a qualified professional service technician. s Ensure that the front glass door assembly is in place and sealed After adjustment. Main Burner Factory Air Shutter Opening Setting—Inches (millimeter) Model Nat.Gas Propane Gas 40 in. 1/16 (1.59) 9/32 (7.14) 45 in.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 FINISHING REQUIREMENTS Wall Details .ON COMBUSTIBLE MATERIALS SUCH AS SURROUNDS AND OTHER APPLIANCE TRIM MAY BE INSTALLED ON THE APPLIANCE FRONT FACE WITH THE EXCEPTIONS #OMPLETE lNISHED INTERIOR WALL 4O INSTALL THE APPLIANCE FACING mUSH WITH THE lNISHED WALL POSITION FRAMEWORK TO ACCOMMODATE THE THICKNESS OF THE lNISHED WALL (Figure 51).
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 Step 11. INSTALLER INSTRUCTIONS—ATTACHING SAFETY-IN-OPERATION WARNINGS It is the installers responsibility to ensure these warnings are properly affixed during installation. These warning labels are a critical step in informing consumers of safe operation of this appliance.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 INSTALLATION ACCESSORIES Listed Secure Vent® Components Cat. No. Model No.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 GAS CONVERSION KITS Step 1. TURN OFF THE GAS SUPPLY TO THE APPLIANCE and disconnect power supply at the circuit breaker. Ensure appliance is cold. WARNING This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 Step 6.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.
)../6!4)6% (%!24( 02/$5#43 s $)2%#4 6%.4 '!3 &)2%0,!#%3 -ONTEBELLO$,8 -ONTEBELLO$,8#$ s ).34!,,!4)/. ).3425#4)/.3 )NNOVATIVE (EARTH 0RODUCTS RESERVES THE RIGHT TO MAKE CHANGES AT ANY TIME WITHOUT NOTICE IN DESIGN MATERIALS SPECIlCATIONS AND PRICES AND ALSO TO DISCONTINUE COLORS STYLES AND PRODUCTS #ONSULT YOUR LOCAL DISTRIBUTOR FOR lREPLACE CODE INFORMATION 0RINTED IN 5 3 ! Ú )NNOVATIVE (EARTH 0RODUCTS ,,# 34 P/N 506023-22 Rev. NC 12/2013 %LM (ILL 0IKE 3UITE s .ASHVILLE 4.
