Installation & Assembly

ManualsBrandsAstoria Grand ManualsBronze Outdoor Hanging LightsBaxter 1-Light Outdoor Hanging Lantern

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing

the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool

before removal. Do not subject glass parts to any shock while in operation or shattering may result.

1of6

Part

Description

Quantity

A Crossbar

Nipple

1pc.

2 pcs.

1pc.

Hex Nut

Package Contents

Canopy Chain Loop

Lock Washer

1pc.

Canopy Lock Ring

1pc.

Fixture Chain

Ceiling Canopy

Fixture Body

ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wire

strippers,electrical tape,safety glasses.

EstimatedAssemblyTime:20-30 minutes

BulbRecommended: (1) MediumBase 100WMaximum

Preparation:Identify andinspect allparts beforebeginning installation.Checkpackage

contentlist anddiagrams belowto besureallpartsarepresent.If anyparts aremissing

ordamaged, donot attemptto assemble,install, oroperatethefixture.Contactcustomer

servicefor replacementparts.

Assembly Instruction

Summary of content (6 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Bulb Recommended: (1) Medium Base 100W Maximum Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
FINISH: IMPERIAL BRONZE 5" Dia. Q U IO ZEL 1" 2.4 m m 13 G a GND 2 Overall Height 117.5” (Includes 96” Chain) 1 19" 3 10.5" Dia. (1)100W Medium Base Bulb (Not Supplied) NO. NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2" REPLACEMENT PART DESCRIPTION REQ. 1 CHAIN IMPR BRNZ 3.
PAGE 3
Assembly Instruction . . , . STEP 1 - Attach Crossbar to Outlet Box Outlet Box A. Secure the Crossbar (A) to the outlet box with outlet box screws (not supplied). Tighten until snug. Crossbar Mounting Hole Outlet Box Screw (not Supplied) Figure 1 STEP 2 - Attach Nipple to Crossbar A. Thread one Hex Nut (D) onto the top end of the Nipple (B). B. Place one Lock Washer (C) over the top end of the Nipple (B) and then thread the Nipple (B) into the center lock hole of the Crossbar (A). C.
PAGE 4
Assembly Instruction . . , . STEP 4 - Assemble Ceiling Canopy Outlet Box A. Push the Ceiling Canopy (H) upward over the Outlet Box. Thread the Canopy Lock Ring (F) onto the Canopy Chain Loop (E) and tighten until snug to secure the Ceiling Canopy (H). Canopy Chian Loop Ceiling Canopy Canopy Lock Ring Figure 4 STEP 5 - Attach Fixture Chain to Canopy Chain Loop and Fixture Loop A. Adjust the Fixture Chain (G) to your desired length by removing the links if needed.
PAGE 5
Assembly Instruction . . STEP 6 - Pass Supply Wires through Fixture Chain Canopy Chain Loop A. Pull the Supply Wires and Ground Wire up through the Fixture Chain (G) alternating links. Push the wires up through the Canopy Chain Loop (E) into the outlet box. Fixture Chain Supply Wire and Ground Wire Figure 6 STEP 7 - Make Wire Connections A. Un-thread the Canopy Lock Ring (F) and slide Canopy Lock Ring (F) and Ceiling Canopy (H) down the Fixture Chain (G). B.
PAGE 6
Assembly Instruction STEP 8 - Install Bulb A. This fixture uses standard bulb with a standard screw base . Maximum 10 0 watts. B. Place the bulb from the bottom of the glass frame. Insert bulb and screw snugly into place. Socket Your fixture hanging lamp is now assembled and ready to use.