QUETEC SoftGate Wireless AP/Router solution (PCMCIA/PCI/USB interface) User’s Guide ~English version~ ~中文繁體使用手冊請參照繁體中文部份~ ~中文简体使用手册请参照简体中文部份~ Version Q3. 0 July2004 http://www.quetec.net Copyright 2004. All Rights Reserved. Document Version: Q3.0 All trademarks and trade names are the properties of their respective owner.
COPYRIGHT No part of this Publication may be reproduced, transmitted, transcribed, and stored in retrieval System, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Chapter 1 QUETEC SoftGate I ntroduction This Chapter provides an overview of the SoftGate AP/ Router's features and specifications. Thank you for purchasing the QUETEC SoftGate wireless solution adapter. QUETEC SoftGate is the first AP less series family product to turn the existing computers into a wireless AP. I t includes four features (4- in-1): Router, AP, Bridge, and WLAN Client.
1.1 QUETEC SoftGate Features 1.1 z z z z z 4 in 1 Device— Integrates Router, AP, Bridge, and Client into your PC/Laptop. Easy Installation & Expansion—Simple, affordable and flexible solution break through your wireless limitation. Complete Mobility—Small size, portable wireless base station. Security—64-bit or 128 bit encryption. Intelligent device— Auto-detect and configure for client or infrastructure AP. 1.2 QUETEC SoftGate Specifications Standard IEEE802.
1.3 QUETEC SoftGate Interface description The QUETEC SoftGate AP/Router solution provides several kinds of interface: z z z PCMCIA: for PC card type II PCI: for 32 bit PCI 2.2 USB: for USB 1.0 (2.
Chapter 2 Installation Overview 2.1 QUETEC SoftGate Setup on Laptop/Desktop PC ＊You should estimate around several minutes to complete the installation. Before you begin the installation process, make sure you have the proper SoftGate Wi-Fi adapter and installation CD and that the Laptop/Desktop PC which you are installing onto has a proper open slot. 2.2 QUETEC SoftGate Requirements The machine installing SoftGate needs to have supported OS running.
2.3 QUETEC SoftGate Quick Installation Once you are ready to install, follow these steps: STEP 1. For PCMCIA and USB: Insert QUETEC SoftGate Software CD into your computer first, and the autorun program will launch the setup wizard, then choice the adapter icon to run the setup program. For PCI only: Insert the PCI adapter into your PC slot first, and then restart your PC.
Chapter 3 What’s in the Box 3.1 Package content The following items should be included • 1 QUETEC SoftGate Wi-Fi adapter (PCMCIA/PCI/USB) • 1 Installation Autorun CD: contents in the CD include o SETUP.EXE: QUETEC SoftGate installer o Userguide: User’s Guide • 1 piece of Quick installation guide card • 1 USB cable (for USB package only) If any of the above items are damaged or missing, please contact your dealer immediately.
Chapter 4 Check Your System Please make sure again that the computer you are installing the QUETEC SoftGate meets as following minimum system requirements: • Computer with CPU PII 366MHz or better • 128MB RAM or better • Windows ME, 2000, XP • An open slot based on the adapter in the package • CDROM drive 10
Chapter 5 QUETEC SoftGate Installation Procedures The procedures described in this section to install and configure the QUETEC SoftGate Wireless LAN device under MS Windows 2000/XP. Caution: Please do not insert your PCMCIA card until the Application setup asks you to do so. The setup procedure described below installs both the drivers and the QUETEC SoftGate Manager Utility. If the SoftGate Manager Utility were installed before, you need uninstall the previous version first.
-Click on “Next”, a license agreement will be displayed, Click on “Yes” if you agree and continue the installation. -Click the installation type you prefer, and then click “Next” to continue. (We recommend that you choice the “Express” at this moment) During the set up procedure, if you see the Windows pop-up dialog shows the message about Hardware installation warning, just click “Yes” to next step.
-The setup wizard will execute the installation procedure automatically, -For the PCMCI A/ USB installation, you will see a pop-up screen to ask to insert the QUETEC SoftGate compatible device. Please insert your PCMCI A/ USB into your system, then the wizard will continue to install procedure automatically.
-At this moment, QUETEC SoftGate installation wizard will configure your computer as an AP only mode. -After the setup procedure, you will see as following message, Click the “Next” button. -I f you see the as following message, it means the set up procedure is completed. You can use any other computers running Wi-Fi card to check QUETEC SoftGate functionality. I t should be listed as one of the available netw ork.
5.1 Window s ME I nstallation Notes QUETEC SoftGate I nstallation Using a PCMCI A/ USB Adapter When installing SoftGate on a PC running Windows ME, you cannot have the adapter inserted into the PCMCI A/ USB slot during the install process. Do not insert the PCMCI A/ USB until the SoftGate installer requests you to do so.
3. Because the SoftGate enabled PC will share the I nternet connection select: “ Yes this computer uses the follow ing”, and “A direct connection to an I SP using the follow ing device”. 4. Click the down arrow to see a list of adapters that can be shared. Select the network adapter that is connected to your broadband modem. Press Next. 5. Select “Yes” when asked if you would like other users to be able to access this computers I nternet connection.
5.2 Window s 2000 I CS Setup I t is highly recommended that you upgrade Windows 2000 to Service Pack 4. I f you cannot make this upgrade, you must manually configure I CS on Windows 2000 after installing SoftGate. 1. Verify your cable modem, DSL or other broadband connection is w orking properly. Verify you can connect to the I nternet over your broadband connection. 2. Open the Properties for the netw ork adapter that is connected to your broadband modem and click on the "Sharing" Tab.
Chapter 6 QUETEC SoftGate Manager 6.1 Overview After the successful installation, you can find the following items in Start menu: All Programs: Quetec: SoftGate. Also in your system tray. Quetec SoftGate Manager provides detailed control of SoftGate operation. This is the main screen of SoftGate. • • • • Green light blinks on the top right corner indicates proper SoftGate operation. Status: Shows the SoftGate mode and adapter status. Number of clients: How many clients connected to SoftGate.
6.2 AP/ Client mode setup procedures under WinXP To access the “Options” menu select Tools> Options from the SoftGate menu bar. - Select “Tools”, “Switch to the Station Mode”, you can easily switch from AP to station as you want.
-I n “Tools” section, use “Disable the wireless” to disable/ enable the wireless connection. -Select “Tools”, “Options”, to enter the detailed setup for SoftGate Manager. -I n “Options” area, you can change wireless related settings, incl. General Setting, Wireless AP, Devices, and MAC Filtering. To apply any changes you made, please click on “O.K” button.
-The Wireless AP interface provides an interface for general configuration settings for language and station mode client configuration Language Settings: Use the pull down menu to select the language pack for SoftGate. Station Mode Softw are: SoftGate provides the capability to operate in station mode to access wireless access points.
• • • • I srael China France Spain Channel: The 802.11 wireless channel that SoftGate will use to broadcast traffic. Advanced Settings ( Button) : Fine tuning of SoftGate network settings - primarily for network troubleshooting or expert users. - I n “Devices” setting area , you can change the network connection mode. e.g. move from office to home, you can use “I CS/ Bridge Settings” to redirect the network settings, and also to share the network connection.
Mode Sw itch Options: This setting allows you to configure SoftGate to automatically scan for the best available settings when you switch from station to Access Point mode. Use the pull down menu to choose the mode switch • • • Auto Scan for Best Available Settings Prompt for Connection Settings Use Previous Settings -Enter the “ MAC Filtering setting” area to enable the MAC filtering function, choice the filter method that you want to use.
-Choice the “ Status…”menu to monitor the wireless AP, Devices and Stations (Status of connected clients) status. To access the “ Status” menu select Tools> Status from the SoftGate menu bar The SoftGate status menu provides various interfaces that allow the SoftGate administrator quick and easy access to the overall configuration details of SoftGate.
-Choice the “ Change Admin Passw ord…” to change your SoftGate password.
* Client mode function under WinXP Under WinXP system, please using default wireless network utility when switching to station mode. You can find it on “Control panel”: “Networking”. Make sure to choice “Use Window s to configure my w ireless netw ork settings” to enable w ireless client function.
6.3 AP/Client mode setup procedures under Windows 2000The Window s 2000 AP set up procedures is almost the same as WinXP, only for the client function choice must do some changes as follow ing: - I n “General Settings” at “Station Mode Software”, mark the “Use the following software when in station mode”, and make your selection.
z Client mode function under Window s 2000for PCMCIA and PCI Interface z You can find the QUETEC client utility icon in the system tray when you are in Station mode. Double click utility icon start using the program. - I n “ Profile ” section, can select different configuration modes. - Push the “ Refresh ” button, it can show all available wireless network/ APs. - Select one network name and push the “ Quick Connect ” button, you can easily connect to the wireless network.
- From “ Country” section, you can do select your region and push “ Apply” button to enable the change. - I n “ Site Survey” section, you can get the updated network information via pushing “ Refresh ” button.
z Client mode function under Window s 2000for USB Interface only ~ This section is only for SoftGate USB solution under station mode. For the PCMCIA and PCI solution, please refer to PCMCIA and PCI section. ~ You can find the wireless client utility icon in the system tray when you are in Station mode. Double-click the crab icon, following dialog box will appear. The “ NetStatus” tab shows the Link Status, Network mode, SSI D, Channel, Tx. Rate.
I n “ Site Scan ”, Push “ Re- Fresh ” button to survey all available AP sites, You can assign Access Point or Ad-hoc devices which you want to connect. Push the “ Connect ” button to link the AP. I t also provides the “ Add to Profile ” function. * The “ Add to Profile ” function provide user to save its wireless connection data into Profile database. Just push the“ Add to Profile ” button, and it will pop-up as following dialog windows that showing the detailed data.
Find the “ profile ” data in this tab. You can add new profile or edit pervious one in this session. Select the “ Statistics” tab, you will see the Link Status, Signal strength, and transmit/ receive statistics. I f check the Turn Radio OFF, the radio interface will be turn off.
Select the “ Encryption ” tab. I f you want to enable the function, please set the Data Encryption to WEP. WEP encrypts each frame transmitted from the radio using one of the Keys entered from this panel. To be written to the driver and registry, each key must consist of hex digits, which means that only digit 0-9 and letters A -F are valid entries. I f entered incorrectly program will not write keys to a driver. * For more detailed setting, please refer to QUETEC SoftGate Security section.
6.4 QUETEC SoftGate Security As mentioned in the SoftGate introduction, securing your SoftGate enabled network is essential in a wireless network environment. Security for the SoftGate enabled wireless network is maintained through three primary features: • • • Support for the Wired Equivalency Protocol (WEP) Support for MAC address filtering Automatically enables MS I CF on Windows XP (MS I nternet Connection Firewall) WEP Key Configuration The wired equivalency protocol or WEP is an 802.
MAC Address Filtering SoftGate supports MAC address filtering for either allowing or denying access to individual clients. A MAC address (Media Access Control) is a unique hardware address for networking equipment. The MAC address is used by the network for associating an IP addresses to a users networking hardware, in this case their wireless LAN adapter. Because each MAC address is unique, it is suitable to use a MAC address for filtering purposes.
Chapter 7 QUETEC SoftGate Appendix 7.1 Appendix A: Quetec SoftGate Help I nterface Quetec SoftGate Help Interface SoftGate features a comprehensive “Help” interface that provides quick answers to common questions concerning SoftGate network modes and configuration. To access the SoftGate “Help” interface, simply select Help from the main toolbar menu.
Chapter 8 Troubleshooting The following are known issues with the SoftGate: 8.1 Standby/Resume Cycle During a standby and resume cycle, SoftGate may stop functioning. If this happens, please restart the computer. 8.2 Connect to SoftGate but can’t access internet If a client machine connects to the SoftGate, but cannot access the internet, check that the SoftGate machine has internet access. Run “ipconfig” and make sure that the SoftGate has two connections, one for the internet and one for the SoftGate.
Access Point Only Mode - Overview Access Point only mode provides basic access point functionality in a closed network environment. Typically, this mode is configured when an external LAN is not available. This mode is the default mode that is configured if the SoftGate host PC is not connected to an external network through a wired LAN adapter.
Microsoft I CS Mode Overview MS I CS (Microsoft I nternet Connection Sharing) mode provides wireless AP connectivity to SoftGate clients and I nternet Connection Sharing to an existing LAN through the SoftGate hosts LAN adapter. When SoftGate is configured in MS I CS mode, SoftGate clients are leased I P addresses using DHCP services from the SoftGate host. The range of I P addresses assigned to clients in this mode are 192.168.0.0-255.
Bridge Mode Overview Bridge mode provides wireless AP connectivity to SoftGate clients, and bridges the existing wired LAN segment(s) with the SoftGate host’s wireless LAN adapter. Typically, a bridge is used to interconnect physical LAN segments on a network that already provides DHCP and routing services. I n a typical use case, SoftGate will run on a PC to provide wireless AP functionality to client devices.
8.4 SoftGate more reliable & easier to use than Ad-Hoc networks Ad-Hoc networks allow users to create a simple wireless network without the use of an access point. However, there are several drawbacks when relying on ad-hoc networks for wireless networking: 1: Ad-Hoc netw orks do not use the normal packet collision avoidance technique ( RTS/ CTS) because of the “False Blocking” problem. 802.11 networks deploy a packet collision avoidance mechanism called RTS/ CTS (Ready to Send / Clear to Send).
3. Ad-hoc netw orks are also susceptible to netw ork breakdow n due to their decentralized nature. Figure (3) shows the ad-hoc network functioning properly, as all clients are able to communicate with each other. Figure (4) demonstrates how easy it is, though, for an ad-hoc network to break down. Because the client node in the middle is performing all of the routing for the other nodes, as soon as the client in the middle exits the network or changes locations, the entire network breaks down.
QUETEC SoftGate Wireless AP/Router solution (PCMCIA/PCI/USB interface) 中文繁體使用手冊 版本 C3.0 July 2004 www.quetec.net Copyright 2004. All Rights Reserved. Document Version: C3.0 All trademarks and trade names are the properties of their respective owners.
著作權 任何全部或部份的出版品，不能以文章格式。內容意思及任何衍生作品，例如翻譯或改編性的文章，從1 9 7 6年 的美國著作權法規定，不能敘述廠商內容的法律規範。 COPYRIGHT No part of this Publication may be reproduced, transmitted, transcribed, and stored in retrieval System, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.
FCC安全指示 本產品已經過＜Class B 數位裝置＞測試及嚴格要求。此限制按照F C C規則的1 5個部分。這些限制是為了在居住環 境中安裝任何設備，提供合理的保護，和對抗有害干擾而設計。若未按照指示正確的安裝或使用，此設備可能會產 生或散發射頻能源，並可能對電訊交通造成有害的干擾。但是，並不保證在特殊的安裝中，不會產生干擾。 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
第一章 產品介紹 本章節提供對於Quetec SoftGate無線基地台/路由器之特性及規格總覽. 首先感謝您選購由Quetec SoftGate所研發生產的SoftGate無線網路方案，此產品能夠提 供您連接您的桌上型/筆記型電腦以及無線的區域網路設備。無需任何傳統纜線佈置或 無線存取點/路由器, Quetec SoftGate無線網路方案提供家庭或辦公室使用族群更具彈性 且更容易上手的無線資訊環境,您可以輕鬆且安全的進行訊息傳遞,網際網路應用或者是 與其他人進行如印表機等資源分享.同時,您不必求助於MIS的協助與維護更可省下一筆 龐大的硬體設備費用.無論是在家庭,公園或是辦公室內Quetec SoftGate無線網路解決方 案提供您無線空間的移動自由,讓您即刻進行訊息分享傳遞,享受無線寬頻上網的熱趣.
1.1 QUETEC SoftGate 產品特性 1.2 z z z z 超值四合一功能— 整合路由器、無線接入點、橋接器及無線網路卡等功能 符合 802.11b 無線傳輸標準 安裝/使用簡易— 自動偵測及設定無線接入點或無線使用端 安全/具彈性—支援 64/128-bit 加密設計，確保資料傳輸安全 1.2 QUETEC SoftGate 規格 標準 符合 IEEE802.11b 無線傳輸標準 介面型態 PCMCIA, PCI, MiniPCI, USB 多工模式 路由器, 無線基地台, 橋接器, 及無線網路卡 調制技術 直接序列擴頻技術 DSSS 安全機制 64/128bit WEP 加密; TKIP(Temporal Key Integrity Protocol) 無線頻率 2.412 ~ 2.462 GHz (美國,) 2.412 ~ 2.484 GHz (日本) 2.412 ~ 2.472 GHz (歐洲) 2.457 ~ 2.462 GHz (西班牙) 2.457 ~ 2.
1.3 QUETEC SoftGate 介面描述 QUETEC SoftGate AP/Router 無線方案提供數種介面型態: z z z PCMCIA: 符合 PC card type II PCI: 符合 32 bit PCI 2.2 USB: 符合 USB 1.0(2.
第二章 硬體安裝總覽 2.1 QUETEC SoftGate PCMCIA/PCI/USB 介面安裝圖示 ＊本安裝過程可能需要數分鐘完成. 注意：為了節省您寶貴的時間，在您開始安裝前,我們建議您先確認手邊有符合安裝所需要的正確設 備。包括SoftGate 無線介面裝置, 安裝光碟, 以及可供使用的電腦插槽.. 2.2 安裝前確認事項 所欲安裝之機器必須配備 SoftGate 所支援之作業系統如視窗 ME/2000 或 XP. 預先確認所安裝之機器已可順利藉由微軟 IE 瀏覽器連結到網際網路. 假如所欲安裝之機器已先裝有其他無線網路卡,請在安裝 SoftGate 前先到開始: 控 制台:系統: 硬體: 裝置管理員: 網路介面卡, 選擇您正在使用的無線網路卡, 按滑鼠 右鍵, 關閉此一裝置運作.
2.3 QUETEC SoftGate 快速安裝指南 一旦您已準備好進行安裝後, 請依下列步驟指示: 步驟一. PCMCIA與USB介面: 先將SoftGate安裝光碟插入欲安裝之電腦光碟機中,自動安裝程 式將會啟動安裝精靈,接下來請在視窗中選擇你所要安裝的介面裝置圖形開始進行安裝 程式. 使用PCI介面: 首先關閉電源將PCI介面卡插入電腦PCI槽中後重新啟動電腦. 當系統出 現安裝新硬體精靈時, 請按取消選項後將SoftGate安裝光碟插入欲安裝之電腦光碟機 中,自動安裝程式將會啟動安裝精靈,接下來請在視窗中選擇你所要安裝的介面裝置圖 形開始進行安裝程式. 步驟二. 程式將自動執行安裝並設定所有的動作,當安裝精靈出現插入適合的介面卡裝置訊息時, 請依照安裝精靈的指示將介面卡插入指定的槽位中,按下一步繼續安裝動作. 步驟三. 繼續依照安裝精靈所要求的動作完成所有驅動程式及應用工具的安裝. 此時softGate將 會自動將你的電腦設定為無線基地台模式.
第三章 QUETEC SoftGate 包裝內容 3.1 檢查包裝 在您開始安裝本產品之前，請先將您所購得之產品與以下的配件清單檢查比對，以確 定沒有任何配件有損壞或遺漏的清況發生。完整的產品配件應包含下列物件， 物件如 有任何短少，請速與原經銷單位聯絡，以確保您的權益： 包裝內容包含: • 1 片 QUETEC SoftGate 無線網路介面卡(PCMCIA 或 PCI 或 USB) • 1 片自動安裝光碟: 光碟內容如下 o SETUP.
第四章 系統需求 請再次確認您欲安裝之電腦系統配備符合 SoftGate 最低之需求 : • 電腦配備中央處理器需 PII 366MHz 或以上 • 128MB 記憶體或以上 • 微軟視窗 ME, 2000, XP • 一組可以使用之插槽 • 光碟機 52
第五章 QUETEC SoftGate 安裝程序說明 此一章節說明將引領您基於微軟視窗 2000/XP 作業系統下進行 SoftGate 無線網路裝置 的安裝與設定. 注意. 請勿先將 PCMCIA 介面卡插入機器,請在接或安裝指示通知你後再將卡片插入. 假如您先前曾安裝過舊版 SoftGate 程式,請先將它移除後再開始進行安裝步驟. - 將自動安裝光碟插入光碟機然後按下你所欲安裝之 SoftGate 裝置圖示, 會自動跳出安 裝歡迎畫面.
- 按下 “Next” 鍵後, 將會出現版權聲明畫面, 假如您同意版權內容請按下 “Yes” 後繼續進行安裝步驟. 如您不同意請按下“No” 後離開 SoftGate 安裝程式 - 選擇您所要安裝的模式後按“Next” 鍵, 進行下一步動作.
- 安裝精靈將會自動執行安裝步驟, - 針對 PCMCI A/ USB 介面安裝, 您會看到要求您插入 SoftGate 合適的裝置之對話視窗. 此時請將 PCMCI A/ USB 插入您的電腦插槽, 安裝精靈將會自動繼續進行安裝步驟.
- 此時, SoftGate 安裝精靈將自動設定為無線基地台模式. - 在安裝過程後, 您將會看到下列訊息, 請按 “Next” 鍵繼續安裝動作. - 請按”Finish” 鍵完成安裝步驟. 您可以使用配備有其他無線網路卡的電腦進行連結,並測試 SoftGate 所提供的超強功能. 您應該同時也能在可用網路清單中發現 SoftGate.
5.1 Window s ME 安裝重點提示 使用 SoftGate PCMCI A/ USB 介面安裝 當您要在 Windows ME 作業系統下安裝 SoftGate, 在安裝過程中請勿將 PCMCI A/ USB 介面卡插入電腦中. 請勿將 PCMCI A/ USB 介面卡插入, 直到 SoftGate 安裝程式要求你時再進行此一動作. 使用 SoftGate PCI 介面安裝 先關閉電源將 PCI 介面卡插入電腦 PCI 槽中,並確定卡片安裝妥當. 在看到 ”加入新硬體” 精靈視窗時,請關閉此一程式,並開始執行 SoftGate 的安裝 光碟. 安裝 Window s Me I CS 功能 在安裝好 SoftGate 之後欲將 SoftGate 設定在站台模式, 在 Windows ME 作業系統下您 必須手動設定 I CS 以便分享網際網路連接. 下列步驟將協助您如何進行 I CS 設定. 請在 安裝妥 SoftGate 後依循下列指示. 7. 下列步驟將協助您在 Windows Me 下設定 ICS 模式. • 選擇開始 > 設定 > 控制台> 新增/ 移除程式.
9. 因為 SoftGate 可以讓允許 PC 啟動網際網路分享之選項: 你可以看到下列訊息 “ Yes this computer uses the follow ing”, 及 “A direct connection to an I SP using the follow ing device”. 10. 按下選項箭頭 (如下圖示) 將會出現可供分享之介面卡清單. 選擇您所使用來連 接寬頻數據機之網路介面卡後按 Next 鍵. 11. 當視窗出現”您是否要讓其他使用者透過您的電腦分享網際網路連線”訊息時 請按“Yes” 鍵. 此時下拉式選幕中出現可供其他使用者連接之介面卡訊息時,請 務必自清單中選擇 SoftGate 介面卡. 按 Next 鍵. 12. 此時將會出現”是否需要製作家庭網路安裝磁片”訊息視窗. 您可以選擇”NO “結束安裝步驟, 或者您可以進行製作家庭網路安裝磁片動作,讓其他電腦使用 此一安裝磁片. 假如你選擇製作家庭網路安裝磁片請依照螢幕所指示之步驟進行 之. 注意: 請參考您的 Windows Me 使用手冊 或進入 http://support.microsoft.
5.2 設定 Window s 2000 I CS 模式 在此非常強烈建議您升級您的 Windows 2000 作業系統到 Service Pack 4. 假如你無法 升級, 那您必須完成安裝 SoftGate 後在 Windows 2000 系統下手動進行設定 I CS 設定. 5. 確認您的纜線數據機, DSL 或其他寬頻連接設備正常運作. 並確認你可以透過寬頻連 接設備聯結到網際網路. 6. 開啟連接寬頻數據機之網路介面卡內容選項後按下 "Sharing" 選項區. • 操作步驟: 在 桌面之"My Network Places" 圖示輕壓滑鼠右鍵, 選擇 "Properties", 在"Local Area Connection" 圖示上 按滑鼠右鍵,選擇"Properties" 選項. 7. 勾選"Enable I nternet Connection sharing for this connection" 選項啟動 I CS 模式. 8. 此時已設定為無線基地台的 SoftGate 將可讓連接上之無線網路用戶利用微軟之 ICS 模 式進行網際網路連結分享.
第六章 QUETEC SoftGate 操作管理者 6.1 總覽 當成功安裝完 SoftGate 後,您可以在開始:所有程式集與工作列找到 QUETEC SoftGate 圖示.
