c ctiv olle e pit ch ad 3D qu copt INST er ANUA M N IO RUCT Specification: TYPE: Collective Pitch Electric 3D Quadcopter Rotor Diameter: 118MM Length:635 MM Width: 365 MM Weight: 986g w/out battery Flying weight : 1240g w/battery L
1.0 Important Information Table of Contents 1.0 Important Information 1 2.0 Assault Reaper 500 3D Set up Instructions 2 (1) The Assault Reaper 500 3D is not a toy, this Multirotor utilizes high-tech components and technologies to provide superior performance in flight. Improper use of this product can result in serious injury or even death. Please read this manual carefully before use and be conscious of your own personal safety and the safety of others 3.0 Assault Reaper 500 3D Assembly 3-13 4.
2.
3.0 Assault Reaper 500 3D Assembly No.1 Front Pulley Block Assembly (1) Slide the drive belt through the left and right fixed tubes respectively. Right fixed tube (2) Face the fixed tube gap downwards, secure to the front pulley block, and tighten the fixing screw.
No.2 Back Pulley Block Assembly (1) Slide the drive belt through the left and right fixed tubes respectively. (2) Face the fixed tube gap downwards, secure to the back pulley block, and tighten the fixing screw.
NO.3 Front End Assembly Drive Shaft And Middle Fixed Tube Driven wheel (1) Place the front end of the drive shaft through the drive wheel and bearing, tighten the fixing screw on the flat position. (2) Fit the middle fixed tube to the front pulley block, and tighten the fixing screw. Flat position Fr on t Notice: The Flat section of the shaft is to be connected to the front end of the airframe as illustrated.
NO.4 Rear End Assembly Drive Shaft and Middle Fixed Tube. Middel fixed tube M2x8 screw Driven shaft Ba ck M2 fixing nut Driven wheel M3x3 screw (1) Slide the back end of the drive shaft through the drive wheel and bearing, tighten the fixing screw on the second flat position. Second flat position First flat position (2) Fit the middle fixed tube to the back pulley block, and tighten the fixing screw.
NO.5 Main Drive Gear and Brushless Motor Assembly. (1) Fit the main drive gear onto the drive shaft, and tighten the fixing screw on the flat position. (2) Fit the brushless motor to the back pulley block, move it up and down until the main drive gear and motor mesh smoothly, then tighten the fixing screw to secure.
NO.6 Instructions For Drive Belt Assembly (1) The arrows represent the rotation direction. (2) When assembling the drive belt try to keep it tight to avoid vibration in operation. Rotate the end of the drive belt 90 degrees counter-clockwise when assembled. Front Rotate the end of the drive belt 90 degrees clockwise when assembled. Rotor4 Rotor1 Rotor3 Rotor2 Rotate the end of driven belt 90 degrees clockwise when assembled. Rotate the end of drive belt 90 degrees counter-clockwise when assembled.
NO.7 Rotor 2 / Rotor 4 Assembly M2x14 screw (1) Install the drive belt to Rotor 2, ensure the rotation is correct. Control the swing arm (2) Install Rotor 2 front and rear seat, and tighten the fixing screw. (3) Install Rotor 4 in the same manner as Rotor 2.
NO.8 Rotor 1 / Rotor 3 Assembly M2x14 (1) Install the drive belt to Rotor 3, ensure the rotation is correct. (2) Install the Rotor 3 front and rear fixed seat, and tighten the fixing screw. Control the swing arm (3) Install Rotor 1 in the same manner as Rotor 3.
No.9 Pull Rod Assembly Pull rod Pull rod (1) Once the steering servos have been positioned to centre, the steering gear control swing arm must be positioned at an angle of 90 degrees to ensure correct operation. Pull rod (2) Connect the pull rod joint buckle to the ball end, the propeller PITC should be at an angle of 0 degrees. If necessary adjust this accordingly.
No.10 Reinforcing Plate, Skid Landing and Propeller Assembly. Front M3x14 screw M3 fixing nut Leading Edge of the blade Reinforcing plate (1) Install the reinforcing plate to the bottom of the front back pulley block. KB2x5 (2) Install the bottom cover and skid landing to the bottom of the front, back pulley block. Skid landing PA2x11 Bott om c over (3) Install the propeller into the propeller clip according to the rotation.
No.11 ESC, Main Controller, Receiver, Battery, Canopy Assembly Canopy Front Canopy support beam (1) Install the ESC to the backend of the mount plate. (2) Install the main controller to the mount plate. (3) Install the receiver to the mount plate. Battery (4) Install the battery to the mount plate. (5) For wiring diagrams please refer to 4.0: main controller port instructions and 5.0: ESC instructions. Receiver (6) Fix the canopy to the support beam.
4.0 Main Controller Set Up Guidelines 11 12 13 7 10 9 8 6 14 5 4 3 2 1 1 AUX1 IN: connect to receiver AUX1 port 2 Servo 1: connect to servo 1 3 Servo 2: connect to servo 2 4 Servo 3: connect to servo 3 5 Servo 4: connect to servo 4 6 THRO OUT: connect to ESC 7 RUDD IN: connect to receiver RUDD port 8 THRO IN: connect to receiver THRO port 9 AILE IN: connect to receiver AILE port 10 ELEV IN: connect to receiver ELEV port 11 12 13 14 ELEV G.
5.0 Brushless Speed Controller Set up Connect to main controller THRO OUT port Black Blue Red Yellow Green Brushless Motor Red Connect to battery Attention: The brushless motor should rotate in a clockwise direction, if not, exchange any two the motor connection wires to obtain the correct rotation.
6.0 T-SIX Transmitter Settings 6.1 Initial INFO Screen Elevator Trim(Mode 1) Throttle Trim(Mode 1) Throttle Trim(Mode 2) Elevator Trim(Mode 2) Model Type Current model number 7.2V REAPER50 MDL 1 Current Model Voltage DN 06:00 Time [ NORM ] Helicopter Flight Mode HELI Rudder Trim Aileron Trim The INFO screen is displayed when the power is switched on.
(4) Trim set up: The trim set up function allows servo movement (1) Voltage: When the transmitter voltage drops below 4.3 volts, “Warning Low Battery” will flash along with an alarm sound. If you are flying when this occurs, land immediately. adjustment. (5) Model display: you can see the selected model directly after your (2) Timer: Timer function allows you to program a Count Down timer or model type has been selected. Stop Watch (count up timer) to display on the main screen.
(1) LIST Key: when this key is pressed the screen changes to the Function Listing screen. (2) ENTER Key: If this key is pressed when the INFO screen is being displayed, the screen will change to the My list screen. This can be used for moving to each of the other functions. (3) Up Key: if this key is pressed the select cursor will move up to your desired menu or list. (4) DOWN Key: if this key is pressed the select cursor will move down to your desired menu or list.
6.5 MODEL TYPE MODEL TYPE Rotate ROLLER SETUP LIST MODEL TYPE Press ROLLER ACRO HELI Rotate ROLLER to choose HELI, press ROLLER to confirm. When finished, press ROLLER to return to SETUP LIST menu. 6.6 SWASH TYPE SETUP LIST SWASH TYPE Rotate ROLLER SWASH TYPE Press ROLLER 1 SERVO90° Rotate and press ROLLER to choose “1 SERVO90°”, press ROLLER to confirm. When finished, press ROLLER to return to SETUP LIST menu. 6.
6.8 GYRO FUNCTION LIST Rotate ROLLER GYRO GYRO Press ROLLER RATE Rotate ROLLER to choose and change the settings and press ROLLER SW-GYRO POS0 80.0% POS1 70.0% POS1 50.0% to confirm. When finished, press ROLLER to return to FUNCTION LIST menu. 6.9 THRO CUR FUNCTION LIST Rotate ROLLER THRO CUR THRO CUR NORM STU HOLD L 0.0 100 100.0 2 42.0 88.0 3 70.0 80.0 4 85.0 88.0 H 100 100 Press ROLLER NORM (%) THRO CUR NORM STU HOLD L 0.0 100 100.0 2 42.0 88.0 3 70.0 80.0 4 85.0 88.
6.10 PITC CUR FUNCTION LIST Rotate ROLLER PITC CUR PITC CUR NORM STU HOLD 0.0 L 40.0 25.0 2 50.0 38.0 25.0 3 58.0 50.0 50.0 4 68.0 63.0 75.0 100 H 75.0 75.0 Press ROLLER NORM Rotate ROLLER to choose and change the settings and press ROLLER to confirm. When finished, press ROLLER to return to Initial Info Screen. (%) PITC CUR NORM STU HOLD L 40.0 25.0 0.0 2 50.0 38.0 25.0 3 58.0 50.0 50.0 4 68.0 63.0 75.0 H 75.0 75.0 100 STU PITC CUR NORM STU HOLD L 40.0 25.0 0.0 2 50.0 38.0 25.0 3 58.0 50.0 50.
7.0 Binding the Transmitter and Receiver binding plug (1) Insert the bind plug in the BATT/ BIND slot on the receiver. (2) Move the throttle sticker to the LOW/OFF position. Then power on the radio. (3) Connect the flight battery to the receiver, the LED will flash quickly. (4) When the LED becomes a solid continuous light binding is complete. (5) Always remove the bind plug from the receiver once bound.
8.
9.
25
