User's Manual
Table Of Contents
- Safety Instructions / Warning - Read before start-up!
- Preface
- 1 Scope
- 2 Extended Documentation
- 3 Definitions and Abbreviations
- 4 Supported tags
- 5 The mifare® Transponder Family
- 6 ISO 14443 Type B
- 7 Hardware
- 8 Software for contactless interface functions
- 8.1 ASCII Protocol
- 8.2 Binary Protocol
- 8.3 Register Set
- 8.3.1 EEPROM memory organization
- 8.3.2 Unique device ID (00h – 04h)
- 8.3.3 Station ID (0Ah)
- 8.3.4 Protocol configuration (0Bh)
- 8.3.5 BAUD, Baud rate control register (0Ch)
- 8.3.6 Command Guard Time (0Dh)
- 8.3.7 OPMODE, operating mode register (0Eh)
- 8.3.8 Single Shot Time-out (0Fh)
- 8.3.9 Protocol configuration 2 (13h)
- 8.3.9.1 Disable multi-tag reset (default 0)
- 8.3.9.2 Disable start-up message (default 0)
- 8.3.9.3 Enable binary frame v2 (default 0)
- 8.3.9.4 Noisy Environment (default 0)
- 8.3.9.5 Reset Recovery Time Multiplier (default 0)
- 8.3.9.6 Enable ISO14443 B Anti-collision (default 0)
- 8.3.9.7 Disable ISO 14443-4 Error Handling (default 0)
- 8.3.10 Reset Off Time (14h)
- 8.3.11 Reset Recovery Time (15h)
- 8.3.12 Application Family Identifier (16h)
- 8.3.13 Selection Time-out ISO 14443A (17h)
- 8.3.14 Selection Time-out ISO 14443B (18h)
- 8.3.15 Selection Time-out SR176 (19h)
- 8.3.16 Protocol configuration 3 (1Bh)
- 8.3.17 User data (80h - EFh)
- 8.4 Instruction Set
- 8.4.1 Overview
- 8.4.2 Error Codes
- 8.4.3 Common commands
- 8.4.3.1 Test Continuous Read
- 8.4.3.2 Continuous Read
- 8.4.3.3 Set LED
- 8.4.3.4 DES encryption / decryption of data
- 8.4.3.5 Get ID
- 8.4.3.6 Multi-Tag Selection / List
- 8.4.3.7 Include tag type
- 8.4.3.8 Exclude tag type
- 8.4.3.9 Set tag type
- 8.4.3.10 Set Configuration Flags
- 8.4.3.11 Set Configuration Register
- 8.4.3.12 Antenna power on/off
- 8.4.3.13 Read/Write user port
- 8.4.3.14 Quiet
- 8.4.3.15 Read block
- 8.4.3.16 Read reader EEPROM
- 8.4.3.17 Select
- 8.4.3.18 Get Version
- 8.4.3.19 Write DESFire key
- 8.4.3.20 Write master key
- 8.4.3.21 Write block
- 8.4.3.22 Write EEPROM
- 8.4.3.23 Reset
- 8.4.3.24 Field Reset
- 8.4.4 ISO 14443 Type A only commands
- 8.4.5 SR176 only commands
- 8.4.6 DESFire command set
- 8.4.6.1 Authenticate
- 8.4.6.2 Change Key Settings
- 8.4.6.3 Get Key Settings
- 8.4.6.4 Change Key
- 8.4.6.5 Get Key Version
- 8.4.6.6 Create Application
- 8.4.6.7 Delete Application
- 8.4.6.8 Get Application IDs
- 8.4.6.9 Select Application
- 8.4.6.10 Format PICC
- 8.4.6.11 Get Version
- 8.4.6.12 Get File IDs
- 8.4.6.13 Get File Settings
- 8.4.6.14 Select File
- 8.4.6.15 Change File Settings
- 8.4.6.16 Create Standard Data File
- 8.4.6.17 Create Backup Data File
- 8.4.6.18 Create Value File
- 8.4.6.19 Create Linear Record File
- 8.4.6.20 Create Cyclic Record File
- 8.4.6.21 Delete File
- 8.4.6.22 Read Data / Records
- 8.4.6.23 Data files
- 8.4.6.24 Record file
- 8.4.6.25 Write Data / Record
- 8.4.6.26 Get Value
- 8.4.6.27 Credit
- 8.4.6.28 Debit
- 8.4.6.29 Limited Credit
- 8.4.6.30 Clear Record File
- 8.4.6.31 Commit Transaction
- 8.4.6.32 Abort Transaction
- 9 Software for contact interface functions
- 10 Frequently Asked Questions
- 11 References
- 12 Appendix A: SAM
- 13 Appendix C: Timings
- 14 Appendix D: Release Notes
- 15 Appendix F: Approvals / Certificates
ACGPass e-ID Desktop Reader, Ver. Dual ISO 2.3
ASSA ABLOY Identification Technologies GmbH 6
7.1.2 External Connections...........................................................................29
7.1.2.1 USB Cable ................................................................................... 29
7.1.2.2 Power Supply............................................................................... 29
7.1.2.3 SAM Socket ................................................................................. 30
7.1.3 Function Control Indicator LEDs ..........................................................31
7.1.3.1 Power LED................................................................................... 32
7.1.3.2 RFID activity indicator LED .......................................................... 32
7.1.3.3 USB Online indicator LED............................................................ 32
7.1.3.4 Contact Interface activity indicator LED ....................................... 33
8 Software for contactless interface functions ..............................34
8.1 ASCII Protocol............................................................................................ 34
8.2 Binary Protocol........................................................................................... 34
8.2.1 STX......................................................................................................35
8.2.2 Station ID .............................................................................................35
8.2.3 Length..................................................................................................35
8.2.4 Flags ....................................................................................................35
8.2.5 Data .....................................................................................................35
8.2.6 Block Check Character (BCC)..............................................................36
8.2.7 ETX......................................................................................................36
8.2.8 Remarks...............................................................................................36
8.2.9 Examples: ............................................................................................36
8.3 Register Set ............................................................................................... 37
8.3.1 EEPROM memory organization ...........................................................38
8.3.2 Unique device ID (00h – 04h)...............................................................39
8.3.3 Station ID (0Ah)....................................................................................39
8.3.4 Protocol configuration (0Bh).................................................................39
8.3.4.1 Auto start (default 1) .................................................................... 39
8.3.4.2 Protocol (default 0)....................................................................... 39
8.3.4.3 Multitag (default 0) ....................................................................... 39
8.3.4.4 New serial mode (default 0) ......................................................... 39
8.3.4.5 LED (default 0)............................................................................. 40
8.3.4.6 Single shot (default 0).................................................................. 40
8.3.4.7 Extended Protocol (default 1)....................................................... 40
8.3.4.8 Extend ID (default 0).................................................................... 41
8.3.5 BAUD, Baud rate control register (0Ch)...............................................42
8.3.6 Command Guard Time (0Dh)...............................................................43
8.3.7 OPMODE, operating mode register (0Eh)............................................43
8.3.8 Single Shot Time-out (0Fh) ..................................................................44
8.3.9 Protocol configuration 2 (13h) ..............................................................44
8.3.9.1 Disable multi-tag reset (default 0) ................................................ 44
8.3.9.2 Disable start-up message (default 0) ........................................... 44
8.3.9.3 Enable binary frame v2 (default 0)............................................... 44