NEW GENERATION V1.0-V2.0 EVO Software EUR-USA v8.
America: Digital Centre America, Inc. 14271 SW 120th Street Unit #109 USA, Miami, FL 33186 Sales: Ph: +1.305.387.5005 sales@dc-image.com Europe: Digital Centre Pol. Ind. Sant Isidre C/ Puigmal, 20-22 St. Fruitós 08272, BARCELONA. Spain Ph: +34.938.748.158 info@dc-image.com Tech Support: Ph: +1.305.387.5115 support@dc-image.com www.digital-centre.
Copyright and Trademarks This manual contains materials protected under International copyright Laws. All rights reserved. No part of this manual may be reproduced, transmitted or transcribed without the express written permission of the manufacturer and author of this manual. The information of the products in this manual is subject to change without prior notice and does not represent a commitment on the part of the vendor.
CONTENTS 1. Safety Instructions----------------------------------------------------------------------6-7 2. Specifications------------------------------------------------------------------------------8 3.Unpacking· Installation------------------------ -------------------------------------9-10 4.Features-------------------------------------------------------------------------------10 4.1 Service Control Panel-------------------------------------------------10 4.
11.6 Pink screen-------------------------------------------------------------68 11.7 Black screen-----------------------------------------------------------69 11.8 Printer Error--------------------------------------------------------70-71 11.9 No signal---------------------------------------------------------------72 11.10 Control Board Error------------------------------------------------72 12.Characteristics-----------------------------------------------------------------73-79 12.
1-Safety INSTRUCTIONS The following directions must be followed carefully for safe use, to prevent personal injuries, and damage to the equipment. Please read this entire manual before initial use and store it in a convenient location for on easy access. WARNING: To ensure safe operation, observe specifications, notices and cautions in this document. Digital Centre Accepts no liability for damage or injuries from improper use of this product. WARNING: Prevent electrical shock and equipment damage.
Danger: Power Off the Photo Booth immediately if any of the following occurs: · Smoke · Unusual Odor · Unusual Noise · Water or other Liquids spill inside the Photo Booth · Physical Damage Danger: Do not place or store the Photo Booth in wet or extremely humid areas, in direct sunlight, near an open flame or heater, and/or swimming pools. Avoid Condensation.
2-Specifications NEW GENERATION V1.0 Power Supply: AC 220V 50/60 Hz (110V for USA) Power Consumption: 260W Dimensions: Width= 73 cm - Inch 29 Length= 94,5 cm - Inch 37 Height= 194 cm - Inch 77 Weight = 160 kg / 352 lbs. Nominal fuse rating= 6 Amps Monitor: LCD Color Monitor 17” Printer: Mitsubishi CP9550 Dye Sublimation Photo Printer NEW GENERATION V2.
3-Unpacking · Installation These are the accessories included with your new Digital Centre Photo Booth: Manual Power Cord Keys Boot DVD Warning: Movement of the photo booth requires assistance from two or more people. · Unwrap and remove all packaging materials. Remove screws and metal holding plates that attach the Photo Booth to the skid. · All major components of the Photo Booth are located under the seat. Access to the components is through the lower rear service door.
Adjust the height of the four metal legs once the final location for the booth has been established. The metal legs are underneath the cabin next to the wheels. Plug the power cord into the socket underneath the Photo Booth. Slide the power switch to the “ON” position. 4-FEATURES 4.1 Service Control Panel 1 2 3 4 5 1. Coin Counter 2. Credit (Red Button) 3. Accounts (Black Button): It prints detailed vending report including number of prints available. 4.
5-connections 5.1 CONTROL BOARD CN14 Coin Counter JP7 JP4 Coin Acceptor Power 230V (115V for USA) CNT8 CN8 To Bill Acceptor CN10 Selection Buttons and Test Control Panel Cables JP5 CN6 Serial Cable to PC (P.2) Fuse 1A F1 Volume POT1 CN5 Jack Stereo to PC (P.6) Sound CN3 CN6. Serial Cable. From Control Board to PC. CN8. Bill Acceptor Cable. From Control Board to Bill Acceptor. JP4, JP5 and JP7. We need a jumper here. CNT8. Power Supply at 230 volts (115 volts for USA). CN5. Jack Stereo.
5.2 PC WIRING P.7 P.8 P.2 P.3 P.4 P.5 P.6 P.1 PC WIRING P.1 Main Power Cable. P.2 Serial Cable From PC to Control Board M/F. (56 cm - Inch 22,04) P.3 VGA Cable M/M (180 cm - Inch 70,87) P.4 USB Cable From Printer to PC. (180 cm - Inch 70,87) P.5 USB to Serial Converter. Zoom Sony Camera (20 cm - Inch 7,87) P.6 Jack Stereo Cable. (180 cm - Inch 70,87) P.7 S-VHS Cable M/M From Camera to PC. (250 cm - Inch 99,42) P.8 115 volts - 230 volts Switch.
5.3 PC WIRING to control board D P.1 P.2 P.3 P.1 P.4 P.5 P.6 P.7 C PC WIRING GENERAL WIRING P.1 Main Power Cable. P.2 Serial Cable From PC to Control Board M/F. (56 cm - Inch 22,04) P.3 VGA Cable M/M. (180 cm - Inch 70,87) P.4 USB Cable From Printer to PC. (180 cm - Inch 70,87) P.5 USB to Serial Converter. Zoom Sony Camera (20 cm - Inch 7,87) P.6 Jack Stereo Cable. (180 cm - Inch 70,87) P.7 S-VHS Cable M/M From Camera to PC. (250 cm - Inch 99,42) C.
5.4 PRINTER P.4 P.1 PRINTER WIRING P.1 Main Power Cable. P.4 USB Cable From Printer to PC AM/BM.
5.5 general 1 A 8 9 P.1 5 4 COMPONENTS 7 6 3 PC WIRING P.1 Main Power 1. Printer Mitsubishi CP9550DW-DC. Cable. 2. PC 5. 3. PC-5 Holder. (RAW METAL) 4. Control Board . 5. Wood Printer Base. NG (RAW) 6. Wood PC Base. NG (RAW) 7. Transformer Socket Plastic Base.(WHITE) 8. Security Disconnection Button On-Off-On. 9. Transformer 2A 12V 2 GENERAL WIRING A.
5.6 monitor P.7 P.5 15 20 E P.1 14 16 18 12 22 19 B 13 17 23 21 24 11 25 P.3 P.1 P.7 COMPONENTS 11. Bottom Holders for Monitor. NG (RAW METAL) 12. Metal holder for Camera NG. 13. Top Holders for Monitor. NG (RAW METAL) 14. Camera Glass Metal Holder. (RAW METAL) 15. Sony Camera FCB. 16. Speakers 8 Ohm 5W. (10 cm - Inch 3,94) 17. LCD Monitor 17” ACER. 18. Double Push Buttons Ok/Cancel. NG 19. Double Push Buttons Right/Left. NG 20. Ballast 13W 21. Lateral Light Diffuser Holder.
6-PRINTER WARNING: The printers are not interchangeable · Protective Measures This printer is designed to operate with Photo Booth systems. Do not remove any inside components. Do not try to repair or manipulate it. Before printing, install an Ink sheet and paper. Never insert any object into the unit. Foreign objects of any kind inserted into this unit is safety hazard and can cause extensive damage. Do not place anything on the digital color printer.
Features & Functions FRONT PANEL 1· POWER BUTTON Use to switch the power ON and OFF. Press to turn on power. Press again to turn off power. When a paper jam happens occurs or when the door is open. 2· PRINT OUTLET The printed paper comes out here. 6· PAPER/INK RIBBON INDICATOR When an error concerning the ink ribbon or print paper happens occurs, this indicator illuminates or blinks 3· DOOR OPEN BUTTON When you press this button while the power is on,the door will open in about five seconds.
10· CANCEL BUTTON Press this button for a little over 1 se¬cond to cancel continuous printing. After the button is pressed the printing process is canceled. 11· FEED & CUT BUTTON Hold down this button for a little over 1 second and the printer pa¬per is fed and cut. SIDE AND REAR PANEL 1· USB TERMINAL Use to connect the USB cable. 2· DIP SWITCHES Never touch it. 3· HANDLE FOR TRANSPORTING When transporting this unit, hold this handle and the lower front part of this unit.
INSTALLATION OF PRINT PAPER · SPACERS The spacers are attached to the paper flanges. The spacers are necessary, for reasons see the Quick Setup Guide. Re¬move the cushions put between the paper flange and spacer when using them. How to attach and remove the spacers 1. Turn the spacer until the latches are unlocked. 2. Remove the spacer with the paper flange’s stoppers retracted.
Before Operation 2 Press the POWER button to turn on the power. 3 Press the DOOR OPEN button to open the door. Take the ink cassette in the printer out. 4 Install the print paper into the unit. Make sure to install the print paper firmly. Thermal head (Inside) Direction of paper insertion NOTE Install the print paper into the unit slowly. If it is dropped along the ditches, the unit or accessories may be damaged. CAUTION Do not touch the thermal head right after printing because it is extremely hot.
Before Operation Print paper Roller Black cover 5 Remove the sticker, insert the print paper between the rollers as shown above, and feed the print paper until it reaches the black cover. Remove the sticker before inserting the print paper between rollers. Make sure to insert the paper straight. NOTE · Keep the roller clean. · Dirt on the roller may degrade the print quality. NOTE · When taking the print paper out, pull it up toward you. · Make sure to turn on the power before replacing the print paper.
INSTALLING THE INK CASSETTE 1· Place the ink cassette containing the ink ribbon in the position as shown above. Place the ink cassette on the print paper with the shaft (thicker one) around which the ink ribbon is wound located to the front. Align the arrows marked on the sides of ink cassette with those on the unit. Place the rear of the ink cassette along the guides that are provided inside the unit. Make sure to set the ink ribbon roller to the ditches firmly.
Before Operation 2· Push the ink cassette toward the back of the unit. Hold the handle of the ink cassette and push it straight toward the back of the unit. Then raise it until you hear a click to secure it in the ink cassette holder. NOTE If the ink ribbon is used up, repeat the steps 1 and 2 to replace the print paper and the ink ribbon. Thermal head (Inside) 3· Push the center of the door to close. The print paper setting is initialized two minutes after you close the door.
When the manual & cut mode has been selected When the manual feed & cut mode has been selected, hold down the FEED & CUT button for 1 second or longer. Repeat the manual feed & cut three times. When the print paper with the postcard printing on its reverse side is installed, repeat this procedure five times. To select the auto feed & cut mode, see “Setting of the DIP switches” Installation of the print paper and the ink ribbon is completed.
2· Remove the ink cassette. Push down the ink cassette as shown by the arrow 1 and pull it out. 3· Take out the print paper. When taking the print paper out, pull it up toward you. 4· Cut off the defective part of the print paper with scissors. NOTE Make sure to cut off the printed part of the print paper. Failure to do this may result in the ink ribbon sticking to the print paper and being torn. 5· Install the print paper and the ink cassette with the ink ribbon. 6· Push the center of the door to close.
When the manual feed & cut mode has been selected, hold down the FEED & CUT button for 1 second or longer. Repeat the manual feed & cut three times. When the print paper with the postcard printing on its reverse side is installed, repeat this procedure five times. For how to select the auto feed & cut mode, see “Setting of the DIP switches” Cleaning Cleaning as indicated below will help maintain stable printer operation and extend the printer’s life.
CAUTION · Thermal head is hot right after printing. Wait until the head is cold before cleaning the thermal head. NOTE · The thermal head may be damaged if you touch it while static electricity builds up on your body. PAPER FLANGE CLEANING Clean the parts that contact the print paper sides as shown above.Wipe the parts carefully with tissue paper dampened with a small amount of alcohol.
7-playing Demo Mode DEMONSTRATION When there are no vends, the machine enters in Demo Mode. Photo samples are displayed. Once money is inserted, you are taken to the credit screen. PRODUCT SCREEN PRODUCT SCREEN You can choose 6 different products.
Photo ID Color and Black & White When the instructions conclude, you have the option to choose “Color” or “Back & White” pictures. SHOTS 4 Shots are taken. (3 shots if you activate the logo) PRINTING The pictures are shown on the screen while strips are printing.
Hairstyles SELECT DESIRED LOOK You can choose different hairstyle options SHOTS Align your face with the circle on the screen. Not bigger not smaller! PRINTING The pictures are shown on the screen while the strips are printing.
Hats FRAMES SELECTION Different hats options you may choose from. SHOTS Align your face with the circle on the screen. Not bigger not smaller! PRINTING The pictures are shown on the screen while the strips are printing.
Street Art SHOOTS 3 Shots are taken, Street Art Selection Select one design. PRINTING The Street Art is shown on the screen while the picture is printing.
Get Framed FRAMES SELECTION Different frame options you may choose from. SHOTS 4 Shots are taken. PRINTING The pictures are shown on the screen while the strips are printing.
8-Customized This procedure will allow you to customize your Photo Booth with custom logos, welcome,..., and other ones. 8.1 structure Logo Welcome A Bye USB stick PhotoIdUpload You must create this folder Text BGmusic Frames 1a,1b,1c,1d 2a,2b,2c,2d ...
8.2 logo Logo 1 Welcome A Bye USB stick PhotoIdUpload You must create this folder Text BGmusic Frames 1a,1b,1c,1d 2a,2b,2c,2d ...
2-Create a folder on the USB stick and name it PhotoIdUpload 3-Insert the logo that you want to use in the folder PhotoIdUpload 4-Connect the USB Stick to the Photo Booth 5-Go to Setup Menu (important) and confirm that logo is activated USB stick PhotoIdUpload Logo You must create this folder Height: 600 pixels Width: 800 pixels Sample Logo Logo Characteristics: Name: Logo Size: width: 800 pixels height: 600 pixels Resolution: 300dpi We recommend 300dpi, but it will also work with less resolution.
8.3 WELCOME/BYE Logo Welcome 2 A USB stick Bye PhotoIdUpload You must create this folder Text BGmusic Frames 1a,1b,1c,1d 2a,2b,2c,2d ...
Welcome message Welcome PhotoIdUpload Sample Welcome You must create this folder Specifications: Name: Welcome Size: width: 800 pixels height: 600 pixels Resolution: 72dpi Format: JPG Bye message Bye PhotoIdUpload You must create this folder Sample bye Specifications: Name: bye Size: width: 800 pixels height: 600 pixels Resolution: 72dpi Format: JPG 39
8.4 text Logo Welcome A Bye USB stick PhotoIdUpload You must create this folder 3 Text BGmusic Frames 1a,1b,1c,1d 2a,2b,2c,2d ...
All text in this file is printed vertically on the left side of the photostrips. Rent your Booth (888). 888. 888 Sample: Rent your Booth (888). 888.
8.5 music Logo Welcome A Bye USB stick PhotoIdUpload You must creat this folder Text BGmusic Frames 4 1a,1b,1c,1d 2a,2b,2c,2d ...
8.6 frames Logo Welcome A USB stick PhotoIdUpload You must create this folder Bye Text 5 BGmusic Frames 1a,1b,1c,1d 2a,2b,2c,2d ... FRAMES To create a new framework we will create a file with the following characteristics.
To create a new framework we will create a file with the following characteristics. SAMPLE Name: Check structure name Size: width: 800 pixels height: 600 pixels Resolution: 72dpi Format: PNG It’s very important to save the file of the frames only in PNG format. Create your own customized frame. Inside of the blank area is where the camera will capture the image, and your customized frame will surround the image.
Frames PhotoIdUpload 1a,1b,1c,1d 2a,2b,2c,2d ...
Screen2 7 8 9 7a 7b 8a 8b 9a 9b 7c 7d 8c 8d 9c 9d 11 10 12 10a 10b 11a 11b 12a 12b 10c 10d 11c 11d 12c 12d Screen3 14 13 15 13a 13b 14a 14b 15a 15b 13c 13d 14c 14d 15c 15d 17 16 18 16a 16b 17a 17b 18a 18b 16c 16d 17c 17d 18c 18d 46
Sample If you want to customize the group Nº1 (from screen 1) follow this structure.
Sample If you want to customize the groups Nº1,2 & 3 follow this structure.
9-uploading 1-Switch ON the Photo booth 2-Open the Photo slot door* PRINTER 3-Insert the USB Stick to the PC (HP C2D) (the usb connection is on the left side of the PC) 4-Open the back door of your photobooth. 5-Press the yellow button from the Service Control Panel, to access the Setup Menu.
10-SETUP menu The setup menu is very useful for the owner of the Photo Booth. You can configure the Photo Booth depending on what kind of service you want to offer to your costumers. You can control the timer, check the prices, adjust the camera settings or consult the accounting functions. To go to the setup menu while the Photo Booth is in Demo Mode, press the yellow button (Menu) from the Service Control Panel inside the Photo Booth.
10.1 SWITCH ON/OFF PRODUCT Displayed only activated products. 10.2 PRODUCTS & PRICES You can turn ON the option of Extra copies, extra product and/or also set the price.
10.2 PRODUCTS & PRICES EXTRA COPIES If you activate this option after each item it displays if you want more copies. 10.2 PRODUCTS & PRICES EXTRA COPIES Inserts $1 for more copies.
10.2 PRODUCTS & PRICES EXTRA COPIES When you insert the money, it prints 2 more sets. 10.2 PRODUCTS & PRICES EXTRA PRODUCT If you activate this option. You can make a copy with a new product.
10.3 RENTALS Free Play: YES( ) NO ( ) Timer: YES ( ) NO ( ) Start: 2011-X-X (Day)- XX:XX(Hour) Finish: 2011-X-X (Day)-XX:XX(Hour) Token: YES ( ) NO ( ) 10.4 CUSTOMIZE To set up the Logo, the Welcome and Bye screens, the Fun Frames, to Print date and Print text.
10.5 OPTIONS It defines the parameters for some available features: Cabine Color: Select the color of your Photo Booth Current Time: 2011-X-X (Date) XX:XX(Hour) Demo Music: YES ( ) NO ( ) 10.6 CAMERA In the submenu CAMERA, the owner can set the camera zoom position and brightness.
11-Troubleshooting · GENERAL PROBLEMS Problem The unit switch is ON, but it does not turn on Causes The unit is not plugged in. The voltage is incorrect. Overload: the fuse over the electric socket has been blown. Solutions Check if the unit is correctly connected to the electric ground. Check if the electric ground is receiving electricity. Be sure that the voltage is correct. Change the fuse. Problem The fluorescent does not turn on. Causes The fluorescent lights have been blown.
· Sound Problems Problem The sound does not work Causes The volume is not correct. The configuration menu has the sound set to OFF. Solutions Adjust the volume with the control placed below the test, free-play and start buttons. Change the sound configuration from the test menu (black button). · PRINTER Problems Problem The printer does not print any photos Causes The printer is disconnected. The printer is out of ink or paper. The paper or the ink sheet was not properly installed. Incorrect paper.
· WARNING · If you have any doubts or any problems with the unit and the way it is performing, call a technician to solve the problem. · Devices such as the printer or the camera are very fragile and must be used carefully. Printer Cleaning. Check configuration. Monthly Glasses Cleaning. Weekly. Control Panel Check the functioning of all buttons Monthly Lights Check the functioning of all the lights and the fluorescent light. Monthly Sound Check the sound.
11.1 UPLOADING THE LOGO Problems uploading the logo: Possible causes: 1-USB STICK is damaged 2-The logo specifications/characteristics are not correct 1-USB is damaged · Let’s make a test to see if it works at the computer. · Plug the USB STICK at the front of the PC (HP C2D), and go to Set Up Menu. Then exit the Menu. · Take a picture by choosing the product you want. · After the game, Remove the USB STICK. · Plug the USB STICK in your PC or LapTop.
2-The logo specifications/characteristics are not correct · Plug the USB Stick in your PC or Laptop. · Locate the logo, Placed on the logo and click the right button on your computer mouse to open properties. · The properties should be as follows. Click the right button · Check the logo specifications Logo specifications: Name: Logo Size: width: 800 pixels height: 600 pixels Resolution: 300dpi We recommend 300dpi, but It will also work with less resolution. Format: JPG LOGO Name: Logo Name: NOT LOGO.
11.2 HARD DRIVE hard drive error This procedure is to check if the BIOS settings are correct for an Automatic BOOT-DVD. WARNING!!! This procedure is very dangerous and could cause a PC Malfunction. Please read it carefully and follow all steps one by one. 1· Plug in a Keyboard to the PC. 2· Turn ON the PC (or the whole Photo Booth). 3· When the ASRock screen appears, press “F10” several times until the “BIOS SETUP UTILITY” appears on the screen.
5· Once you are inside the “DEVICE Configuration” please check the following points: •“Hard disk” should be connected at SATA0 •“CD-ROM” should be connected at SATA1 If everything is OK, press ESC to return the Main menu. If Hard disk or CD-ROM or Both are not detected, we should check the PC connections. (Do this work with the PC unplugged from power).
9· Unplug the PC from the power.
IF The Hard Disk is SATA + DVD SATA it will be like this: POWER SATA HARD DISK SATA HARD DISK SATAII_4 DVD SATAII_2 POWER SATA DVD SATA 12· If all connections are fine (as it appears in the pictures), then it is possible that the component, which is not detected at the “IDE CONFIGURATION” Menu, is physically damaged. Please contact Digital Centre for a new part.
11.3 BOOt DVD To Update the Machine or change the software version, please follow these steps: 1· Open the DVD Driver. 2· Insert the “Boot DVD”. 3· Plug Off the Machine. 4· Plug On the Machine after 10 seconds. 5· Wait while the restore program reinstalls the software (a progress bar appears on the screen). The time process is about 30 minutes 6· A black screen appears when the process finishes. 7· Extract the DVD disk. 8· Plug Off the Machine. 9· Plug On the Machine after 10 seconds.
11.4 CAMERA error Problem: The signal does not reach the PC. Cause: · Camera Video S-VHS signal is not arriving to the PC. · Power from behind the printer is offline Problem: If it shows a Camera error but you see your face on the screen that means that the camera is powered correctly and the S-VHS cable is working correctly, but the data harness is not communicating correctly, so the PC and the camera has no communication.
11.5 Blue screen BLUE SCREEN (BLUE CAMERA IMAGE). You take a photo, but your face does not appear on the screen.Only appears a BLUE screen. Cause: · Camera Video S-VHS signal is not arriving to the PC. Check: · Please check S-VHS cable that connects to the back of the computer. It must be all the way in. P.7 P.7 S-VHS Cable M/M From Camera to PC. (250 cm - Inch 99,42) Please check the transformer that is located behind the Printer. That transformer gives12V to the camera and the Computer area Fans.
11.6 pink screen PINK SCREEN (PINK CAMERA IMAGE). Problem: You take a photo, but your face does not appear on the screen. Only PINK screen. Cause: · Capture Board (inside the PC) is damaged or not correctly connected. Check: · Please, open the PC and check that the Capture Board is correctly connected. · If the board is correctly connected, but still Pink screen, then call Digital Centre.
11.7 BLACK screen Problem: Nothing on the screen, just Black.
11.8 PRINTER error POWER Printer lights ON The “Please Wait” error is very common. It looks like as it the PC freezes, but it isn’t. The problem is that the computer is waiting for the right components. When we turn on the Photo Booth, the computer shows the “Please Wait” screen while it checks the Control Board, the USB adapter and the Printer. If any of the components are not ok, the software doesn’t go ON. READY So, when we face this problem we have to check the 3 components.
3· Check the Control Board Serial Connection. (That is the common problem Point). (attached 2 pictures: Correct and Error “Please Wait”). This connection is very easy to lose during transport, or when we work at that area. 4· If all the 3 points are good, then check the Control Board Red LED is ON. Red LED is ON 5· Check that the USB Adaptor (Camera zoom) is correctly connected at the right USB plug (bottom right).
11.9 NO SIGNAL Lights are ON Check if the PC lights are ON. If the lights are on then it appears that the Photobooth is working but the monitor is not. Next steps: When you turn ON the Photobooth, can you see any message on the screen? (ex; manufacturer name, or “NO SIGNAL”)? If this is the case, the VGA cable is probably unplugged or damaged. But if nothing appears on the screen (when you turn ON the Photobooth), please check if there is power to the Monitor.
12-CHARACTERISTICS 12.
12.2 DECALS Standard Blue v1.0 You can use images of 300 dpi to personalize the decals if needed. Save in a JPG format. The size cm (for EUR) inch (for USA) for each one must be: 1-(DE2901) STD DECAL. NG BU #1 Front Door (64,5 x 179,5 cm - Inch 25.20 x 70.47) 2-(DE2902) STD DECAL. NG BU #2 Bottom Right Lateral Door (Photo Slot) (34,5 x 24,5 cm - Inch 13.38 x 9.50) 3-(DE2903) STD DECAL. NG BU #3 Top Right Lateral (24,5 x 128,5 cm - Inch 9.50 x 50.40) 4-(DE2904) STD DECAL.
75
happy people black v2.0 You can use images of 300 dpi to personalize the decals if needed. Save in a JPG format. The size cm (for EUR) inch (for USA) for each one must be: 1-(DE3111) HAPPY-P. DECAL. NG BK #1 Front Door (64,5 x 179,5 cm - Inch 25.20 x 70.47) 2-(DE3112) HAPPY-P. DECAL. NG BK #2 Bottom Right Lateral Door (Photo Slot) (34,5 x 24,5 cm - Inch 13.38 x 9.50) 3-No Top Right Lateral 4-No Top Left Lateral 5-(DE3115) HAPPY-P. DECAL. NG BK #5 Top Back (71’5 x 118 cm - Inch 27.95 x 46.
77
12.3 spare diagramS NEW GENERATION V1.0 (blue) Spare Diagrams ME2909 MAIN BODY. NG V1.0 (BLUE) ME0001 LOCK 1314 ME2908 TOP LIGHT FRONT METAL COVER. NG BLUE (LIGHT GREY) EL3503 LIGHT BULBS 36W/865 GL2900 CAMERA GLASS. (7x8 cm - Inch 2,75x3,15) EL2900 SONY CAMERA FCB EL2910 DOUBLE PUSH BUTTONS OK/CANCEL. NG GL2902 SCREEN GLASS 17” EL2911 DOUBLE PUSH BUTTONS RIGHT/LEFT. NG SE2903 CURTAIN. NG V1 (BLUE) (75x110 cm - Inch 29,5x43,3) EL2904 LCD MONITOR 17” ME2906 MONITOR & CAMERA FRONT METAL BODY.
NEW gENERATION V2.0 (black) Spare Diagrams ME3112 MAIN BODY. NG V2.0 (BLACK) PL0010 “LOOK HERE”#1 METHACRYLATE LEFT ARROW (8x12cm - Inch 3,15x4,72) PL0008 “LOOK HERE”#1 METHACRYLATE RIGHT ARROW (8x12cm - Inch 3,15x4,72) ME3108 TOP LIGHT FRONT METAL COVER. NG BK (GREY) GL2900 CAMERA GLASS. (7x8 cm - Inch 2,75x3,15) EL3503 LIGHT BULBS 36W/865 EL2900 SONY CAMERA FCB EL2910 DOUBLE PUSH BUTTONS OK/CANCEL. NG EL2911 DOUBLE PUSH BUTTONS RIGHT/LEFT. NG ME3106 MONITOR & CAMERA FRONT METAL BODY.
12.4 PARTS LIST 12.4.1 NG BLUE V1.0/V2.0 SONY-BUTTONS CA0005 CA0006 CA0007 CA2900 CA2901 CA2902 CA2903 CA2904 CA2905 CA2910 CA2912 CA2913 CA2914 CA2915 CA3402 CA3407 CA3411 CA3414 CA3416 CA3512 CO0001 CO0002 CO0003 CO0007 CO0014 CO0015 CO0016 CO0019 CO0023 DE2900 DE2901 DE2902 DE2903 DE2904 DE2905 DE2906 DE2907 DE2908 DE2909 DE2910 DE2911 DE2912 COIN READER CABLE ALBERICI BILL READER CABLE ICT-DC. 12V (92,5 cm - Inch 36,41) BILL READER CABLE MEI-DC.
DE2913 DE2914 DE2915 DE2916 DE2917 DE2918 DE2919 DE2931 DE2932 EL0001 EL2900 EL2901 EL2902 EL2903 EL2904 EL2905 EL2910 EL2911 EL3406 EL3408 EL3417 EL3503 EL3504 EL3505 EL3506 EL3507 EL3508 EL3509 EL3510 EL3511 EL3513 EL3603 EL3409 GL2900 GL2902 ME0001 ME0002 ME0014 ME0031 ME0035 ME2901 ME2903 ME2904 ME2906 ME2908 ME2909 ME2910 STARS DECAL. NG BU #3 - TOP RIGHT LATERAL (24,5x128,5 cm - Inch 9,5x50,4) STARS DECAL.
ME2911 CURTAIN ROD. NG V1.0 ME2912 CURTAIN ROD. NG V2.0 (CURVED) ME2913 FLOOR (ALUMINIUM). NG ME2925 MONITOR HOLDER NG V1.0 (RAW METAL) ME2926 MONITOR HOLDER NG V2.0 (RAW METAL) ME2930 METAL LEG (16x80 mm - Inch 0,06x0,315) ME2931 CURTAIN ROD SUPPORT NG v2.0 ME2932 COVER PLATE FOR BILL ACCEPTOR HOLE. (BLUE) (12x15 cm - Inch 4,72x5,91) ME3109 TOP LIGHT DIFFUSER HOLDER. NG (RAW METAL) ME3305 LATERAL LIGHT DIFFUSER HOLDER. RIGHT/LEFT NG (RAW METAL) ME3310 PC-5 HOLDER.
12.4.2 NG BLACK V1.0/V2.0 SONY-BUTTONS CA2900 CA2901 CA2902 CA2903 CA2904 CA2905 CA2910 CA2912 CA2913 CA2914 CA2915 CA3402 CA3407 CA3414 CA3416 CA3512 DE2931 DE2932 DE3110 DE3111 DE3112 MAIN POWER CABLE NG 1/2 (PC + PRINTER + TRAFO 12V + CONTROL BOARD) MAIN POWER CABLE NG 2/2 (1 MONITOR + 2 LATERAL LIGHTS + 1 TOP LIGHT) POWER CORD 110V - USA S-VHS CABLE M/M FROM CAMERA TO PC. (250 cm - Inch 99,42) RS-232 EXTENSION M/F Serial CABLE FROM CAMERA TO PC.
GL2900 GL2902 ME0001 ME0002 ME2911 ME2912 ME2913 ME2925 ME2926 ME2930 ME2931 ME3101 ME3103 ME3104 ME3106 ME3108 ME3109 ME3111 ME3112 ME3132 ME3305 ME3310 ME3311 ME3409 PC0004 PC0005 PC0006 PC0013 PC0014 PC0015 PC2910 PC3301 PC3307 PC3308 PC3309 PL0008 PL0010 PL0017 PL0019 PL0030 PL3101 PL3102 PR9550 SE3101 SE3102 SE3103 SE3402 TO0002 WO2903 WO2904 WO3105 WO3106 WO3107 CAMERA GLASS. (7x8 cm - Inch 2,75x3,15) SCREEN GLASS 17” LOCK 1314 KEY FOR LOCK 1314 CURTAIN ROD. NG V1.0 CURTAIN ROD. NG V2.
CA0005 COIN READER CABLE ALBERICI CA0006 BILL READER CABLE ICT-DC. 12V (92,5 cm - Inch 36,41) CA0007 BILL READER CABLE MEI-DC. 110V CA3411 INTERNAL PC 12V DIVIDER CO0001 COIN ACCEPTOR. (EUR) CO0002 COIN ACCEPTOR. (AUD) CO0003 COIN ACCEPTOR. (CAD) CO0007 ICT DOLLAR BILL ACCEPTOR 12V CO0009 ICT DOLLAR BILL ACCEPTOR SET (DBA+WIRE+12V DIVIDER+METAL BRACKET). (BLACK) CO0011 COIN ACCEPTOR SET (EUR) (COIN ACCEPTOR+FRONT ADAPTER+WIRE+METAL PLATE+METAL CASH BOX & WOOD SUPPORT).
13-notes 86
