Quick Start Manual

ManualsBrandsASRock ManualsDesktopsASRock B85iCafe4

Version 1.0

Published May 2013

No part of this documentation may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this documentation may or may not

be registered trademarks or copyrights of their respective companies, and are used

only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for

informational use only and subject to change without notice, and should not be

constructed as a commitment by ASRock. ASRock assumes no responsibility for

any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide

warranty of any kind, either expressed or implied, including but not limited to

the implied warranties or conditions of merchantability or tness for a particular

purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of prots, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the documentation or product.

e terms HDMI

and HDMI High-Denition Multimedia Interface, and the HDMI

logo are trademarks or registered trademarks of HDMI Licensing LLC in the United

States and other countries.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/

perchlorate”

ASRock Website: http://www.asrock.com

Summary of content (163 pages)

PAGE 1
Version 1.0 Published May 2013 Copyright©2013 ASRock INC. All rights reserved. Copyright Notice: No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
PAGE 2
PAGE 3
B85iCafe4 Motherboard Layout 2 1 PS2 Mouse PS2 Keyboard 3 4 CPU_FAN1 CPU_FAN2 PWR_FAN1 6 5 ATX12V1 ATXPWR1 Top: RJ-45 DDR3_B2 (64 bit, 240-pin module) USB 3.0 T: USB0 B: USB1 DDR3_B1 (64 bit, 240-pin module) USB 2.0 T: USB0 B: USB1 DDR3_A2 (64 bit, 240-pin module) HDMI1 DDR3_A1 (64 bit, 240-pin module) DVI1 VGA1 USB 2.
PAGE 4
No. Description English 2 1 Power Fan Connector (PWR_FAN1) 2 ATX 12V Power Connector (ATX12V1) 3 CPU Fan Connector (CPU_FAN1) 4 CPU Fan Connector (CPU_FAN2) 5 2 x 240-pin DDR3 DIMM Slots (DDR3_A1, DDR3_B1) 6 2 x 240-pin DDR3 DIMM Slots (DDR3_A2, DDR3_B2) 7 ATX Power Connector (ATXPWR1) 8 USB 3.
PAGE 5
B85iCafe4 1 2 3 15 14 13 12 4 5 6 7 8 11 10 9 No. Description No. Description 1 PS/2 Mouse Port 9 Microphone (Pink) 2 D-Sub Port 10 Optical SPDIF Out Port 3 USB 2.0 Ports (USB23) 11 USB 3.0 Ports (USB3_01) 4 LAN RJ-45 Port* 12 USB 2.
PAGE 6
* There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications. ACT/LINK LED SPEED LED LAN Port Activity / Link LED Speed LED Status Description Status Description Off Blinking On No Link Data Activity Link Off Orange Green 10Mbps connection 100Mbps connection 1Gbps connection ** If you use a 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.
PAGE 7
B85iCafe4 Chapter 1 Introduction Thank you for purchasing ASRock B85iCafe4 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance. Because the motherboard specifications and the BIOS software might be updated, the content of this documentation will be subject to change without notice.
PAGE 8
1.2 Specifications English 6 Platform • ATX Form Factor • All Solid Capacitor design CPU th TM • Supports 4 Generation Intel® Core i7 / i5 / i3 / Xeon® / Pentium® / Celeron® in LGA1150 Package • Digi Power Design • 6 Power Phase Design • Supports Intel® Turbo Boost 2.0 Technology Chipset • Intel® B85 • Supports Intel® Small Business Advantage 2.0 Memory • Dual Channel DDR3 Memory Technology • 4 x DDR3 DIMM slots • Supports DDR3 1600/1333/1066 non-ECC, un-buffered memory • Max.
PAGE 9
B85iCafe4 Audio • 7.1 CH HD Audio with Content Protection (Realtek ALC892 Audio Codec) • Premium Blu-ray audio support • TI® NE5532 Premium Headset Amplifier (supports up to 600 Ohms headsets) LAN • • • • • • PCIE x1 Gigabit LAN 10/100/1000 Mb/s Realtek RTL8111G Supports Wake-On-LAN Supports LAN Cable Detection Supports Energy Efficient Ethernet 802.
PAGE 10
• HD Audio Jack: Rear Speaker / Central / Bass / Line in / Front Speaker / Microphone English 8 Storage • 4 x SATA3 6.0 Gb/s connectors, support NCQ, AHCI and Hot Plug • 2 x SATA2 3.
PAGE 11
B85iCafe4 OS • Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit compliant Certifications • FCC, CE, WHQL • ErP/EuP Ready (ErP/EuP ready power supply is required) * For detailed product information, please visit our website: http://www.asrock.com Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using thirdparty overclocking tools.
PAGE 12
1.3 Unique Features ASRock A-Tuning A-Tuning is ASRock’s multi purpose software suite with a new interface, more new features and improved utilities, including XFast RAM, Dehumidifier, Good Night LED, FAN-Tastic Tuning, OC Tweaker and a whole lot more. ASRock Instant Flash ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM. This convenient BIOS update tool allows you to update the system BIOS in a few clicks without preparing an additional floppy diskette or other complicated flash utility.
PAGE 13
B85iCafe4 ASRock XFast RAM ASRock XFast RAM is included in A-Tuning. It fully utilizes the memory space that cannot be used under Windows® 32-bit operating systems. ASRock XFast RAM shortens the loading time of previously visited websites, making web surfing faster than ever. And it also boosts the speed of Adobe Photoshop 5 times faster. Another advantage of ASRock XFast RAM is that it reduces the frequency of accessing your SSDs or HDDs in order to extend their lifespan.
PAGE 14
ASRock Interactive UEFI ASRock Interactive UEFI is a blend of system configuration tools, cool sound effects and stunning visuals. The unprecedented UEFI provides a more attractive interface and more amusment. ASRock Fast Boot With ASRock’s exclusive Fast Boot technology, it takes less than 1.5 seconds to logon to Windows 8 from a cold boot. No more waiting! The speedy boot will completely change your user experience and behavior. ASRock Restart to UEFI Windows® 8 brings the ultimate boot up experience.
PAGE 15
B85iCafe4 ASRock FAN-Tastic Tuning ASRock FAN-Tastic Tuning is included in A-Tuning. Configure up to five different fan speeds using the graph. The fans will automatically shift to the next speed level when the assigned temperature is met.
PAGE 16
Chapter 2 Installation This is an ATX form factor motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Pre-installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings. • Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components.
PAGE 17
B85iCafe4 2.1 Installing the CPU 1. Before you insert the 1150-Pin CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged. 2. Unplug all power cables before installing the CPU.
PAGE 18
English 16 4 3 5
PAGE 19
B85iCafe4 English Please save and replace the cover if the processor is removed. The cover must be placed if you wish to return the motherboard for after service.
PAGE 20
2.
PAGE 21
B85iCafe4 2.3 Installing Memory Modules (DIMM) This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memory Technology. 1. For dual channel configuration, you always need to install identical (the same brand, speed, size and chip-type) DDR3 DIMM pairs. 2. It is unable to activate Dual Channel Memory Technology with only one or three memory module installed. 3.
PAGE 22
1 2 3 English 20
PAGE 23
B85iCafe4 2.4 Expansion Slots (PCI and PCI Express Slots) There are 3 PCI slots and 3 PCI Express slots on the motherboard. Before installing an expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation. PCI slots: The PCI1, PCI2 and PCI3 slots are used to install expansion cards that have 32-bit PCI interface.
PAGE 24
2.5 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins. Clear CMOS Jumper (CLRCMOS1) (see p.1, No. 26) Default Clear CMOS CLRCMOS1 allows you to clear the data in CMOS.
PAGE 25
B85iCafe4 2.6 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard. System Panel Header (9-pin PANEL1) (see p.1, No. 17) PLED+ PLEDPWRBTN# GND 1 GND RESET# GND HDLEDHDLED+ Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below.
PAGE 26
Power LED Header (3-pin PLED1) (see p.1, No. 16) USB 2.0 Headers (9-pin USB4_5) (see p.1, No. 21) (9-pin USB6_7) (see p.1, No. 20) USB 3.0 Header (19-pin USB3_2_3) (see p.1, No. 8) SATA_6 SATA_4 SATA_2 SATA_5 SATA_3 Serial ATA3 Connectors (SATA_1: see p.1, No. 15) (SATA_2: see p.1, No. 14) (SATA_3: see p.1, No. 10) (SATA_4: see p.1, No. 13) PLEDPLED+ PLED+ SATA_1 Serial ATA2 Connectors (SATA_5: see p.1, No. 11) (SATA_6: see p.1, No.
PAGE 27
B85iCafe4 Front Panel Audio Header (9-pin HD_AUDIO1) (see p.1, No. 24) GND PRESENCE# MIC_RET OUT_RET This header is for connecting audio devices to the front audio panel. 1 OUT2_L J_SENSE OUT2_R MIC2_R MIC2_L 1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system. 2.
PAGE 28
(3-pin PWR_FAN1) (see p.1, No. 1) CPU Fan Connectors (4-pin CPU_FAN1) (see p.1, No. 3) (3-pin CPU_FAN2) (see p.1, No. 4) FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND GND +12V CPU_FAN_SPEED ATX Power Connector (24-pin ATXPWR1) (see p.1, No. 7) ATX 12V Power Connector (8-pin ATX12V1) (see p.1, No. 2) 12 24 1 13 8 5 4 1 Infrared Module Header (5-pin IR1) (see p.1, No. 25) IRTX +5VSB DUMMY 1 This motherboard provides a 4-Pin CPU fan (Quiet Fan) connector.
PAGE 29
B85iCafe4 AFD# ERROR# PINIT# SLIN# GND 1 SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# This is an interface for print port cable that allows convenient connection of printer devices. English Print Port Header (25-pin LPT1) (see p.1, No.
PAGE 30
1 Einleitung Vielen Dank, dass Sie sich für das B85iCafe4 von ASRock entschieden haben – ein zuverlässiges Motherboard, das konsequent unter der strengen Qualitätskontrolle von ASRock hergestellt wurde. Es liefert ausgezeichnete Leistung mit robustem Design, das ASRocks Streben nach Qualität und Beständigkeit erfüllt. Da die technischen Daten des Motherboards sowie die BIOS-Software aktualisiert werden können, kann der Inhalt dieser Dokumentation ohne Ankündigung geändert werden.
PAGE 31
B85iCafe4 Plattform • ATX-Formfaktor • Vollständig solides Kondensatordesign Prozessor • Unterstützt Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron® der 4. Generation im LGA1150-Paket • Digipower-Design • 6-Leistungsphasendesign • Unterstützt Intel® Turbo Boost 2.0-Technologie Chipsatz • Intel® B85 • Unterstützt Intel® Small Business Advantage 2.
PAGE 32
• Unterstützt DVI-D mit maximaler Auflösung von 1920 x 1200 bei 60 Hz • Unterstützt D-Sub mit maximaler Auflösung von 1920 x 1200 bei 60 Hz • Unterstützt Auto-Lippensynchronizität, hohe Farbtiefe (12 bpc), xvYCC und HBR (Audio mit hoher Bitrate) mit HDMI (konformer HDMI-Monitor erforderlich) • Unterstützt HDCP-Funktion mit DVI-D- und HDMI-Ports • Unterstützt Blu-ray- (BD) Wiedergabe (Full HD/1080p) mit DVI-D- und HDMI-Ports Audio • 7.
PAGE 33
B85iCafe4 Speicher • 4 x SATA-III-6,0-Gb/s-Anschlüsse, unterstützt NCQ, AHCI und „Hot-Plugging“-Funktionen • 2 x SATA-II-3,0-Gb/s-Anschlüsse, unterstützt NCQ, AHCI und „Hot-Plugging“-Funktionen Anschluss • • • • • • • • • • • • • BIOSFunktion • 64-Mb-AMI-UEFI-Legal-BIOS mit Unterstützung mehrsprachiger grafischer Benutzerschnittstellen • ACPI 1.1-konforme Aufweckereignisse • SMBIOS 2.3.
PAGE 34
Zertifizierungen • FCC, CE, WHQL • ErP/EuP ready (ErP/EuP ready-Netzteil erforderlich) * Detaillierte Produktinformationen finden Sie auf unserer Webseite: http://www.asrock.com Bitte beachten Sie, dass mit einer Übertaktung, zu der die Anpassung von BIOSEinstellungen, die Anwendung der Untied Overclocking Technology oder die Nutzung von Übertaktungswerkzeugen von Drittanbietern zählen, bestimmte Risiken verbunden sind.
PAGE 35
B85iCafe4 1.3 Jumpereinstellung Die Abbildung zeigt, wie die Jumper eingestellt werden. Wenn die JumperKappe auf den Kontakten angebracht ist, ist der Jumper „kurzgeschlossen“. Wenn keine Jumper-Kappe auf den Kontakten angebracht ist, ist der Jumper „offen“. Die Abbildung zeigt einen 3-poligen Jumper, dessen Kontakt 1 und Kontakt 2 „kurzgeschlossen“ sind, wenn eine Jumper-Kappe auf diesen 2 Kontakten angebracht ist. CMOS-löschen-Jumper (CLRCMOS1) (siehe S. 1, Nr.
PAGE 36
1.4 Integrierte Stiftleisten und Anschlüsse Integrierte Stiftleisten und Anschlüsse sind KEINE Jumper. Bringen Sie KEINE Jumper-Kappen an diesen Stiftleisten und Anschlüssen an. Durch Anbringen von Jumper-Kappen an diesen Stiftleisten und Anschlüssen können Sie das Motherboard dauerhaft beschädigen. Systemblende-Stiftleiste (9-polig, PANEL1) (siehe S. 1, Nr. 17) Verbinden Sie Netzschalter, Reset-Taste und Systemstatusanzeige am Gehäuse entsprechend der nachstehenden Pinbelegung mit dieser Stiftleiste.
PAGE 37
B85iCafe4 Serial-ATA-II-Anschlüsse (SATA_5: siehe S. 1, Nr. 11) (SATA_6: siehe S. 1, Nr. 12) Diese beiden SATA-IIAnschlüsse unterstützen SATA-Datenkabel für interne Speichergeräte mit einer Datenübertragungsgeschwindigkeit bis 3,0 Gb/s. SATA_4 SATA_2 Diese vier SATA-IIIAnschlüsse unterstützen SATA-Datenkabel für interne Speichergeräte mit einer Datenübertragungsgeschwindigkeit bis 6,0 Gb/s. USB 2.0-Stiftleisten (9-polig, USB4_5) (siehe S. 1, Nr. 21) (9-polig, USB6_7) (siehe S. 1, Nr.
PAGE 38
Audiostiftleiste (Frontblende) (9-polig, HD_AUDIO1) (siehe S. 1, Nr. 24) Diese Stiftleiste dient dem Anschließen von Audiogeräten an der Frontblende. 1. High Definition Audio unterstützt Anschlusserkennung, der Draht am Gehäuse muss dazu jedoch HDA unterstützt. Bitte befolgen Sie zum Installieren Ihres Systems die Anweisungen in unserer Anleitung und der Anleitung zum Gehäuse. 2.
PAGE 39
B85iCafe4 CPU-Lüfteranschlüsse (4-polig, CPU_FAN1) (siehe S. 1, Nr. 3) (3-polig, CPU_FAN2) (siehe S. 1, Nr. 4) ATX-Netzanschluss (24-polig, ATXPWR1) (siehe S. 1, Nr. 7) +12V PWR_FAN_SPEED GND FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND GND +12V CPU_FAN_SPEED 12 24 1 13 Dieses Motherboard bietet einen 4-poligen CPULüfteranschluss (lautloser Lüfter). Falls Sie einen 3-poligen CPU-Lüfter anschließen möchten, verbinden Sie ihn bitte mit Kontakt 1 bis 3.
PAGE 40
DruckanschlussStiftleiste (25-polig, LPT1) (siehe S. 1, Nr. 22) Deutsch 38 Diese Schnittstelle ist für Druckerkabel vorgesehen und ermöglicht bequemes Anschließen von Druckern.
PAGE 41
B85iCafe4 1 Introduction Nous vous remercions d’avoir acheté cette carte mère ASRock B85iCafe4, une carte mère fiable fabriquée conformément au contrôle de qualité rigoureux et constant appliqué par ASRock. Fidèle à son engagement de qualité et de durabilité, ASRock vous garantit une carte mère de conception robuste aux performances élevées. Les spécifications de la carte mère et du logiciel BIOS pouvant être mises à jour, le contenu de ce document est soumis à modification sans préavis.
PAGE 42
1.2 Français 40 Spécifications Plateforme • Facteur de forme ATX • Conception à condensateurs solides Processeur • Prend en charge les processeurs 4ème Génération Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron® en package LGA1150 • Conception Digi Power • Alimentation à 6 phases • Prend en charge la technologie Intel® Turbo Boost 2.0 Chipset • Intel® B85 • Prend en charge Intel® Small Business Advantage 2.
PAGE 43
B85iCafe4 • Prend en charge le mode DVI-D avec une résolution maximale de 1920x1200 @ 60Hz • Prend en charge le mode D-Sub avec une résolution maximale de 1920x1200 @ 60Hz • Prend en charge les technologies Auto Lip Sync, Deep Color (12bpc), xvYCC et HBR (High Bit Rate Audio) avec HDMI (un écran compatible HDMI est requis) • Prend en charge la fonction HDCP via ports DVI-D et HDMI • Prend en charge la lecture Blu-ray (BD) Full HD 1080p via ports DVI-D et HDMI Audio • Audio 7.
PAGE 44
Stockage • 4 x connecteurs SATA3 6,0 Go/s, compatibles avec les fonctions NCQ, AHCI et « Hot Plug » • 2 x connecteurs SATA2 3,0 Go/s, compatibles avec les fonctions NCQ, AHCI et « Hot Plug » Connectique • • • • • • • • • • • • • Français 42 1 x embase IR 1 x embase pour port d’impression 1 x embase pour port COM 1 x embase LED d’alimentation 2 x connecteurs pour ventilateur de processeur (1 x 4 broches, 1 x 3 broches) 2 x connecteurs pour ventilateur de châssis (1 x 4 broches, 1 x 3 broc
PAGE 45
B85iCafe4 Système d’exploitation • Compatible Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bits Certifications • FCC, CE, WHQL • ErP/EuP Ready (alimentation ErP/EuP ready requise) * pour des informations détaillées de nos produits, veuillez visiter notre site : http://www.asrock.
PAGE 46
1.3 Configuration des cavaliers (jumpers) L’illustration ci-dessous vous renseigne sur la configuration des cavaliers (jumpers). Lorsque le capuchon du cavalier est installé sur les broches, le cavalier est ‘courtcircuité’. Si le capuchon du cavalier n’est pas installé sur les broches, le cavalier est ‘ouvert’. L’illustration représente un cavalier à 3 broches dont les broches 1 et 2 sont « court-circuitées » si un capuchon de cavalier est posé sur ces 2 broches. Cavalier Clear CMOS (CLRCMOS1) (voir p.
PAGE 47
B85iCafe4 1.4 Embases et connecteurs de la carte mère Les embases et connecteurs situés sur la carte NE SONT PAS des cavaliers. Ne placez JAMAIS de capuchons de cavaliers sur ces embases ou connecteurs. Placer un capuchon de cavalier sur ces embases ou connecteurs endommagera irrémédiablement votre carte mère. Embase du panneau système (PANNEAU1 à 9 broches) (voir p.1, No.
PAGE 48
Connecteurs Serial ATA2 (SATA_5: (voir p.1, No. 11) (SATA_6: (voir p.1, No. 12) Ces deux connecteurs SATA2 sont compatibles avec les câbles de données SATA pour les appareils de stockage internes avec un taux de transfert maximal de 3,0 Go/s. SATA_3 SATA_4 SATA_2 Ces quatre connecteurs SATA3 sont compatibles avec les câbles de données SATA pour les appareils de stockage internes avec un taux de transfert maximal de 6,0 Go/s. Embases USB 2.0 (USB4_5 à 9 broches) (voir p.1, No.
PAGE 49
B85iCafe4 Embase audio du panneau frontal (HD_AUDIO1 à 9 broches) (voir p.1, No. 24) Cette embase sert au branchement des appareils audio au panneau audio frontal. Embase du haut-parleur du châssis (SPEAKER1 à 4 broches) (voir p.1, No. 9) Veuillez brancher le hautparleur du châssis sur cette embase. Connecteur sortie SPDIF (SPDIF_OUT1 à 2 broches) (voir p.1, No. 27) Veuillez brancher le connecteur SPDIF_OUT d’une carte VGA HDMI sur cette embase à l’aide d’un câble.
PAGE 50
(PWR_FAN1 à 3 broches) (voir p.1, No. 1) Connecteurs du ventilateur du processeur (CPU_FAN1 à 4 broches) (voir p.1, No. 3) (CPU_FAN2 à 3 broches) (voir p.1, No. 4) Connecteur d’alimentation ATX (ATXPWR1 à 24 broches) (voir p.1, No. 7) Français 48 +12V PWR_FAN_SPEED GND FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND GND +12V CPU_FAN_SPEED 12 24 1 13 Cette carte mère est dotée d’un connecteur pour ventilateur de processeur (Quiet Fan) à 4 broches.
PAGE 51
B85iCafe4 AFD# ERROR# PINIT# SLIN# GND 1 SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# Il s’agit d’une interface pour le câble du port d’impression qui permet un branchement aisé des périphériques d’impression. Français Embase de port d’impression (LPT1 à 25 broches) (voir p.1, No.
PAGE 52
1 Introduzione Grazie per aver acquistato la scheda madre B85iCafe4 ASRock, una scheda madre affidabile prodotta secondo i costanti e rigorosi controlli di qualità di ASRock. La scheda madre offre eccellenti prestazioni con un design robusto che si adatta all'impegno di ASRock di offrire sempre qualità e durata. Dato che le specifiche della scheda madre e del software BIOS possono essere aggiornate, il contenuto di questa documentazione sarà soggetto a variazioni senza preavviso.
PAGE 53
B85iCafe4 Piattaforma • Fattore di forma ATX • Design di condensatore solido CPU • Supporta Intel® CoreTM i7 / i5 / i3 di 4a generazione / Xeon® / Pentium® / Celeron® in LGA1150 Package • Design Digi Power • 6 Power Phase Design • Supporta la tecnologia Intel® Turbo Boost 2.0 Chipset • Intel® B85 • Supporta Intel® Small Business Advantage 2.
PAGE 54
• Supporta DVI-D con una risoluzione max. fino a 1920 x 1200 a 60 Hz • Supporta D-Sub con una risoluzione max. fino a 1920 x 1200 a 60 Hz • Supporta Auto Lip Sync, Deep Color (12 bpc), xvYCC e HBR (High Bit Rate Audio) con HDMI (è necessario un monitor conforme ad HDMI) • Supporta la funzione HDCP con porte DVI-D e HDMI • Supporta Blu-ray (BD) Full HD 1080p, riproduzione con porte DVI-D e HDMI • Audio HD a 7.
PAGE 55
Connettore • • • • • • • • • • • • • 1 x header IR 1 x header porta stampa 1 x header porta COM 1 x header LED di alimentazione 2 x connettori ventola CPU (1 x 4 pin, 1 x 3 pin) 2 x connettori ventola chassis (1 x 4 pin, 1 x 3 pin) 1 x connettore ventola alimentazione (3 pin) 1 x connettore alimentazione ATX a 24 pin 1 x connettore alimentazione da 12 V a 8 pin 1 x connettore audio pannello anteriore 1 x connettore uscita SPDIF 2 x header USB 2.0 (supporto 4 porte USB 2.0) 1 x header USB 3.
PAGE 56
Prestare attenzione al potenziale rischio previsto nella pratica di overclocking, inclusa la regolazione delle impostazioni nel BIOS, l'applicazione di tecnologia di Untied Overclocking o l'utilizzo di strumenti di overclocking di terze parti. L'overclocking può influenzare la stabilità del sistema o perfino provocare danni ai componenti e ai dispositivi del sistema. Occorre eseguirlo a proprio rischio e spese. Non ci riterremo responsabili per possibili danni provocati da overclocking.
PAGE 57
B85iCafe4 1.3 Impostazione jumper L'illustrazione mostra in che modo vengono impostati i jumper. Quando il cappuccio del jumper è posizionato sui pin, il jumper è "cortocircuitato". Se sui pin non è posizionato alcun cappuccio del jumper, il jumper è "aperto". L'illustrazione mostra un jumper a 3 pin i cui pin1 e pin2 sono "cortocircuitati" quando un cappuccio del jumper è posizionato su questi 2 pin. Jumper per azzerare la CMOS (CLRCMOS1) (vedere pag. 1, n.
PAGE 58
1.4 Header e connettori sulla scheda Gli header e i connettori sulla scheda NON sono jumper. NON posizionare cappucci del jumper su questi header e connettori. Il posizionamento di cappucci del jumper su header e connettori provocherà danni permanenti alla scheda madre. Header sul pannello del sistema (PANEL1 a 9 pin) (vedere pag. 1, n.
PAGE 59
B85iCafe4 Connettori Serial ATA2 (SATA_5: vedere pag. 1, n. 11) (SATA_6: vedere pag. 1, n. 12) Questi due connettori SATA2 supportano i cavi dati SATA per dispositivi di archiviazione interna, con una velocità di trasferimento dati fino a 3,0 Gb/s. SATA_4 SATA_2 Questi quattro connettori SATA3 supportano cavi dati SATA per dispositivi di archiviazione interna, con una velocità di trasferimento dati fino a 6,0 Gb/s. Header USB 2.0 (USB4_5 a 9 pin) (vedere pag. 1, n. 21) (USB6_7 a 9 pin) (vedere pag.
PAGE 60
Header audio pannello anteriore (AUDIO1_HD a 9 pin) (vedere pag. 1, n. 24) Questo header serve a collegare i dispositivi audio al pannello audio anteriore. 1. L'audio ad alta definizione supporta le funzioni Jack sensing, ma il filo del pannello sullo chassis deve supportare HDA per funzionare correttamente. Seguire le istruzioni presenti nel nostro manuale e nel manuale dello chassis per installare il sistema. 2.
PAGE 61
B85iCafe4 Connettori della ventola della CPU (CPU_FAN1 a 4 pin) (vedere pag. 1, n. 3) (CPU_FAN2 a 3 pin) (vedere pag. 1, n. 4) Connettore di alimentazione ATX (ATXPWR1 a 24 pin) (vedere pag. 1, n. 7) +12V GND PWR_FAN_SPEED FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND GND +12V CPU_FAN_SPEED 12 24 1 13 Questa scheda madre è dotata di un connettore per la ventola della CPU (Ventola silenziosa) a 4 pin. Se si decide di collegare una ventola della CPU a 3 pin, collegarla al pin 1-3.
PAGE 62
Header porta di stampa (LPT1 a 25 pin) (vedere pag. 1, n. 22) AFD# ERROR# PINIT# SLIN# GND 1 SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# Italiano 60 Si tratta di un'interfaccia per il cavo della porta di stampa che consente una comoda connessione ai dispositivi della stampante.
PAGE 63
B85iCafe4 1 Introducción Gracias por comprar la placa base ASRock B85iCafe4, una placa base fiable fabricada según el rigurosísimo control de calidad de ASRock. Ofrece un rendimiento excelente con un diseño resistente de acuerdo con el compromiso de calidad y resistencia de ASRock. Ya que las especificaciones de la placa base y el software del BIOS podrán ser actualizados, el contenido que aparece en esta documentación estará sujeto a modificaciones sin previo aviso.
PAGE 64
1.2 Especificaciones Español 62 Plataforma • Factor de forma ATX • Diseño de los Condensadores: All Solid CPU • Compatible con 4.ª Generación de Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron® en paquete LGA1150 • Diseño Digi Power • Diseño de 6 fases de alimentación • Compatible con la tecnología de Intel® Turbo Boost 2.0 Conjunto de chips • Intel® B85 • Compatible con Intel® Small Business Advantage 2.
PAGE 65
B85iCafe4 • Compatible con DVI-D con máxima resolución hasta 1920x1200 @ 60Hz • Compatible con D-Sub con máxima resolución hasta 1920x1200 @ 60Hz • Compatible con Auto Lip Sync, Deep Color (12bpc), xvYCC y HBR (audio de alta velocidad de bits) con HDMI (requiere un monitor compatible con HDMI) • Compatible con función HDCP con puertos DVI-D y HDMI • Compatible con reproducción Blu-ray (BD) Full HD de 1080p con puertos DVI-D y HDMI Audio • 7.
PAGE 66
Almacenamiento • 4 conectores SATA3 de 6,0 Gb/s, compatibles con las funciones NCQ, AHCI y “Hot Plug” • 2 conectores SATA2 de 3,0 Gb/s, compatibles con las funciones NCQ, AHCI y “Hot Plug” Conectores • • • • • • • • • • • • • Características del BIOS 1 cabezal IR 1 cabezal de puerto de impresión 1 cabezal de puerto COM 1 cabezal de indicador LED de alimentación 2 conectores de ventilador de la CPU (1 de 4 pines y 1 de 3 pines) 2 conectores de ventilador del chasis (1 de 4 pines y 1 de 3
PAGE 67
B85iCafe4 Certificaciones • FCC, CE, WHQL • Compatible con ErP/EuP (requiere toma de alimentación compatible con ErP/EuP) * Para obtener más información acerca del producto, visite nuestro sitio web: http://www.asrock.com Tenga en cuenta que existen ciertos riesgos relacionados con el overclocking (sobreaceleración), incluyendo el ajuste de la configuración del BIOS, aplicando la Tecnología overcloking no vinculada o utilizando las herramientas de overclocking de tercera parte.
PAGE 68
1.3 Instalación de los puentes La instalación muestra cómo deben instalarse los puentes. Cuando la tapa de puente se coloca en los pines, el puente queda “Corto”. Si no coloca la tapa de puente en los pines, el puente queda “Abierto”. La ilustración muestra un puente de 3 pines cuyo pin 1 y pin 2 son “Cortos” cuando se coloca una tapa de puente en estos 2 pines. Puente de borrado de CMOS (CLRCMOS1) (consulte la pág.1, N.
PAGE 69
B85iCafe4 1.4 Conectores y cabezales incorporados Los cabezales y conectores incorporados NO son puentes. NO coloque tapas de puente sobre estos cabezales y conectores. Si coloca tapas de puente sobre los cabezales y conectores dañará de forma permanente la placa base. Cabezal del panel del sistema (PANEL1 de 9 pines) (consulte la pág.1, N.
PAGE 70
Conectores Serie ATA2 (SATA_5: consulte la pág.1, N.º 11) (SATA_6: consulte la pág.1, N.º 12) Estos dos conectores SATA2 son compatibles con cables de datos SATA para dispositivos de almacenamiento interno con una velocidad de transferencia de datos de hasta 3,0 Gb/s. Español 68 SATA_3 SATA_4 SATA_1 SATA_2 Conectores Serie ATA3 (SATA_1: consulte la pág.1, N.º 15) (SATA_2: consulte la pág.1, N.º 14) (SATA_3: consulte la pág.1, N.º 10) (SATA_4: consulte la pág.1, N.
PAGE 71
B85iCafe4 Cabezal de audio del panel frontal (HD_AUDIO1 de 9 pines) (consulte la pág.1, N.º 24) Este cabezal se utiliza para conectar dispositivos de audio al panel de audio frontal. Cabezal de altavoces del chasis (SPEAKER1 de 4 pines) (consulte la pág.1, N.º 9) Conecte el altavoz del chasis a este cabezal. Conector de salida SPDIF (SPDIF_OUT1 de 2 pines) (consulte la pág.1, N.º 27) Conecte el conector SPDIF_OUT de una tarjeta VGA HDMI a este cabezal con un cable.
PAGE 72
(PWR_FAN1 de 3 pines) (consulte la pág.1, N.º 1) Conectores del ventilador de la CPU (CPU_FAN1 de 4 pines) (consulte la pág.1, N.º 3) (CPU_FAN2 de 3 pines) (consulte la pág.1, N.º 4) Conector de alimentación ATX (ATXPWR1 de 24 pines) (consulte la pág.1, N.º 7) Español 70 +12V PWR_FAN_SPEED GND FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND GND +12V CPU_FAN_SPEED 12 24 1 13 Esta placa base contiene un conector de ventilador (ventilador silencioso) de CPU de 4 pines.
PAGE 73
B85iCafe4 GND SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# Ésta es una interfaz para el cable del puerto de impresión que permite una cómoda conexión de dispositivos de impresión. Español AFD# Cabezal de puerto de ERROR# PINIT# SLIN# impresión (LPT1 de 25 pines) 1 (consulte la pág.1, N.
PAGE 74
1 Введение Благодарим вас за приобретение надежной материнской платы ASRock B85iCafe4, выпускаемой под постоянным строгим контролем компании ASRock. Эта материнская плата обеспечивает великолепную производительность и характеризуется прочной конструкцией в соответствии с требованиями компании ASRock в отношении качества и долговечности.
PAGE 75
B85iCafe4 Платформа • Форм-фактор ATX • Использование только твердотельных конденсаторов ЦП • Поддержка процессоров 4-го поколения Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron® в исполнении LGA1150 • Digi Power Design • Система питания 6 • Поддержка технологии Intel® Turbo Boost 2.0 Чипсет • Intel® B85 • Поддержка Intel® Small Business Advantage 2.
PAGE 76
• Поддержка DVI-D с максимальным разрешением до 1920x1200 при 60 Гц • Поддержка D-Sub с максимальным разрешением до 1920x1200 при 60 Гц • Поддержка Auto Lip Sync, Deep Color (12bpc), xvYCC и HBR (High Bit Rate Audio) по HDMI (необходим HDMIсовместимый монитор) • Поддержка функции HDCP через порты DVI-I и HDMI • Поддержка воспроизведения Full HD 1080p Blu-ray (BD) через порты DVI-D и HDMI Русский 74 Аудио • 7.
PAGE 77
B85iCafe4 • • • • • • • • • • • • • 1 x колодка IR 1 x колодка порта принтера 1 x колодка СОМ-порта 1 x колодка светодиодного индикатора питания 2 x разъем для вентилятора ЦП (1 х 4-контактный, 1 х 3-контактный) 2 x разъем для вентилятора корпуса (1 х 4-контактный, 1 х 3-контактный) 1 x разъем для вентилятора блока питания (3-контактный) 1 х разъем питания АТХ (24-контактный) 1 x 8-контактный разъем питания 12 В 1 x аудиоразъем на передней панели 1 x выходной разъем SPDIF 2 x колодки USB 2.
PAGE 78
* Д ля получения дополнительной информации об изделии посетите наш веб-сайт: http://www.asrock.com Следует учитывать, что разгон процессора, включая изменение настроек BIOS, применение технологии Untied Overclocking Technology и использование инструментов разгона независимых производителей, сопряжен с определенным риском. Разгон процессора может повлиять на стабильность системы или даже привести к повреждению ее компонентов и устройств.
PAGE 79
B85iCafe4 1.3 Установка перемычек Установка перемычек показана на рисунке. При установке колпачковой перемычки на контакты перемычка «замкнута». Если колпачковая перемычка на контакты не установлена, перемычка «разомкнута». На рисунке показана 3-контактная перемычка с замкнутыми контактами 1 и 2 при установке на них колпачковой перемычки. Перемычка сброса настроек CMOS (CLRCMOS1) (См. стр. 1, № 26) по умолчанию Сброс настроек CMOS Русский CLRCMOS1 используется для удаления данных CMOS.
PAGE 80
1.4 К олодки и разъемы, расположенные на материнской плате Расположенные на материнской плате колодки и разъемы перемычками НЕ являются. НЕ устанавливайте на эти колодки и разъемы колпачковые перемычки. Установка колпачковых перемычек на эти колодки и разъемы может вызвать неустранимое повреждение материнской платы. Колодка системной панели (9-контактная, PANEL1) (См. стр.
PAGE 81
B85iCafe4 Разъемы Serial ATA2 (SATA_5: (См. стр. 1, № 11) (SATA_6: (См. стр. 1, № 12) Эти два разъема SATA2 предназначены для подключения кабелей SATA внутренних запоминающих устройств для передачи данных со скоростью до 3,0 Гб/с. SATA_4 SATA_2 Эти четыре разъема SATA3 предназначены для подключения кабелей SATA внутренних запоминающих устройств для передачи данных со скоростью до 6,0 Гб/с. Колодки USB 2.0. (9-контактная, USB4_5) (См. стр. 1, № 21) (9-контактная, USB6_7) (См. стр.
PAGE 82
Аудиоколодка передней панели (9-контактная, HD_ AUDIO1) (См. стр. 1, № 24) Эта колодка предназначена для подключения аудиоустройств к передней аудиопанели. 1. Аудиосистема высокого разрешения поддерживает функцию распознавания разъема, но для е правильной работы необходимо, чтобы провод панели корпуса поддерживал передачу сигналов HDA. Инструкции по установке системы см. в этом руководстве и руководстве на корпус. 2.
PAGE 83
B85iCafe4 (3-контактный, PWR_ FAN1) (См. стр. 1, № 1) FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND GND +12V CPU_FAN_SPEED (3-контактный, CPU_ FAN2) (См. стр. 1, № 4) Разъем питания АТХ (24-контактный, ATXPWR1) (См. стр. 1, № 7) PWR_FAN_SPEED 12 24 1 13 Эта материнская плата снабжена 4-контактным разъемом для малошумящего вентилятора ЦП. Если вы собираетесь подключить 3-контактный вентилятор процессора, подключайте его к контактам 1-3. Эта материнская плата снабжена 24-контактным разъемом питания АТХ.
PAGE 84
Колодка порта принтера (25-контактная, LPT1) (См. стр. 1, № 22) AFD# ERROR# PINIT# SLIN# GND 1 SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# Русский 82 Это — интерфейс для подключения кабеля порта принтера, обеспечивающий удобное подключение устройств печати.
PAGE 85
B85iCafe4 1 Introdução Obrigado por ter comprado a placa principal ASRock B85iCafe4, uma placa principal fiável produzida sob os rigorosos critérios de controlo de qualidade da ASRock. Esta placa principal oferece um excelente desempenho com um design robusto em conformidade com o compromisso da ASRock em fabricar produtos de qualidade e resistentes.
PAGE 86
1.2 Especificações Português 84 Plataforma • Formato ATX • Design de condensador sólido CPU • Suporta processadores Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron® de 4ª geração em socket LGA1150 • Design Digi Power • Design com 6 fases de alimentação • Suporta a tecnologia Intel® Turbo Boost 2.0 Chipset • Intel® B85 • Suporta a tecnologia Intel® Small Business Advantage 2.
PAGE 87
B85iCafe4 Áudio • Áudio HD de 7.1 canais com protecção de conteúdo (Codec de áudio Realtek ALC892) • Suporte áudio Blu-ray superior • TI® NE5532 (suporta amplificador de auscultadores premium até 600 Ohms) LAN • • • • • • LAN Gigabit 10/100/1000 Mb/s PCIE x1 Realtek RTL8111G Suporta Wake-On-LAN Suporta Detecção de cabo LAN Suporta IEEE 802.
PAGE 88
Armazenamento • 4 x conectores SATA3 a 6,0 Gb/s, com suporte para NCQ, AHCI e funções “Hot Plug” • 2 x conectores SATA2 a 3,0 Gb/s, com suporte para NCQ, AHCI e funções “Hot Plug” Conector • • • • • • • • • • • • • Português 86 1 x Terminal IV 1 x Terminal de porta de impressão 1 x Terminal de porta COM 1 x Conector para LED de alimentação 2 x Conectores da ventoinha da CPU (1 x 4 pinos, 1 x 3 pinos) 2 x Conectores da ventoinha do chassis (1 x 4 pinos, 1 x 3 pinos) 1 x Conector da ventoi
PAGE 89
B85iCafe4 Sistema Operativo • Compatível com Microsoft® Windows® 8 / 8 64-bits / 7 / 7 64bits Certificações • FCC, CE, WHQL • Preparada para ErP/EuP (é necessária uma fonte de alimentação preparada para ErP/EuP) * Para obter informações detalhadas acerca do produto, visite o nosso Web site: http://www.asrock.
PAGE 90
1.3 Configuração dos jumpers A imagem abaixo ilustra como os jumpers são configurados. Quando a tampa do jumper é colocada nos pinos, o jumper é "Curto". Se não for colocada uma tampa de jumper nos pinos, o jumper é "Aberto". A imagem ilustra um jumper de 3 pinos cujos pino1 e pino2 estão "Curtos" quando a tampa do jumper é colocada nestes 2 pinos. Jumper para limpar o CMOS (CLRCMOS1) (consultar p.1, N.º 26) Predefinição Limpar CMOS Português CLRCMOS1 permite-lhe limpar os dados no CMOS.
PAGE 91
B85iCafe4 1.4 Terminais e conectores integrados Os terminais e conectores integrados NÃO são jumpers. NÃO coloque tampas de jumpers sobre estes terminais e conectores. Colocar tampas de jumpers sobre os terminais e conectores irá causar danos permanentes à placa principal. Terminal do painel de sistema (PAINEL1 de 9 pinos) (consultar p.1, N.º 17) Ligue o botão de alimentação, o botão de reposição e o indicador do estado do sistema no chassis a este terminal de acordo com a descrição abaixo.
PAGE 92
Conectores ATA2 de série (SATA_5: consultar p.1, N.º 11) (SATA_6: consultar p.1, N.º 12) Estes dois conectores SATA2 suportam cabos de dados SATA para dispositivos de armazenamento interno com uma velocidade de transferência de dados de até 3,0 Gb/s. 90 SATA_3 SATA_4 SATA_1 SATA_2 Português Conectores ATA3 de série (SATA_1: consultar p.1, N.º 15) (SATA_2: consultar p.1, N.º 14) (SATA_3: consultar p.1, N.º 10) (SATA_4: consultar p.1, N.
PAGE 93
B85iCafe4 Terminal de áudio do painel frontal (HD_AUDIO1 de 9 pinos) (consultar p.1, N.º 24) Este terminal destina-se à ligação de dispositivos áudio ao painel de áudio frontal. Terminal do altifalante do chassis (SPEAKER1 de 4 pinos) (consultar p.1, N.º 9) Ligue o altifalante do chassis a este terminal. Conector de saída SPDIF (SPDIF_OUT1 de 2 pinos) (consultar p.1, N.º 27) Ligue o conector SPDIF_ OUT da placa VGA HDMI a este terminal através de um cabo.
PAGE 94
(PWR_FAN1 de 3 pinos) (consultar p.1, N.º 1) Conectores da ventoinha da CPU (CPU_FAN1 de 4 pinos) (consultar p.1, N.º 3) (CPU_FAN2 de 3 pinos) (consultar p.1, N.º 4) Conector de alimentação ATX (ATXPWR1 de 24 pinos) (consultar p.1, N.º 7) Português 92 +12V PWR_FAN_SPEED GND FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND GND +12V CPU_FAN_SPEED 12 24 1 13 Esta placa principal inclui um conector de ventoinha de CPU (Ventoinha silenciosa) de 4 pinos.
PAGE 95
B85iCafe4 AFD# ERROR# PINIT# SLIN# GND 1 SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# Esta é uma interface para cabo de porta de impressão que permite a ligação conveniente de dispositivos de impressão. Português Terminal de porta de impressão (LPT1 de 25 pinos) (consultar p.1, N.
PAGE 96
1 Giriş ASRock'ın zorlu kalite kontrol süreçlerinden geçmiş olan ASRock B85iCafe4 anakartını satın aldığınız için teşekkür ederiz. Sağlam tasarımı ile ASRock'ın kalite ve dayanıklılık taahhüdüne uygun şekilde mükemmel performans sağlar. Anakart özellikleri ve BIOS yazılımı güncellenebileceğinden, bu dokümantasyonun içeriği herhangi bir bildirimde bulunulmaksızın değiştirilebilir.
PAGE 97
B85iCafe4 Platform • ATX Form Faktörü • Tam Katı Bağlayıcı tasarımı CPU • 4ncü Nesil Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron®, LGA1150 Paketinde desteklemektedir • Dijital Güç Tasarımı • 6 Güç Safhası Tasarımı • Intel® Turbo Boost 2.0 Teknolojisini destekler Yonga kümesi • Intel® B85 • Intel® Küçük İşletme Avantaj 2.
PAGE 98
• 1920x1200 @ 60Hz'ye kadar DVI-D işlevini destekler • 1920x1200 @ 60Hz'ye kadar çözünürlükle D-Sub işlevini destekler • HDMI ile Otomatik Dudak Senkronizasyonu (12bpc=, xvYCC ve HBR (Yüksek Bit Hızında Ses) özelliklerini destekler (Uyumlu bir HDMI monitörü kullanılmalıdır) • DVI-D ve HDMI bağlantı noktaları ile HDCP işlevini destekler • DVI-D, ve HDMI bağlantı noktalarıyla, Full HD 1080p Bluray (BD) kayıttan yürütme özelliklerini destekler • İçerik Koruma Özelliği ile 7.
PAGE 99
B85iCafe4 Depolama • 4 x SATA3 6,0 Gb/s bağlayıcıları NCQ, AHCI ve “Hot Plug” işlevlerini destekler • 2 x SATA2 3,0 Gb/s bağlayıcıları NCQ, AHCI ve “Hot Plug” işlevlerini destekler Bağlayıcı • • • • • • • • • • • • BIOS Özelliği • • • • Destek CD'si • Sürücüler, Yardımcı Yazılımlar, AntiVirüs Yazılımı (Deneme Sürümü), CyberLink MediaEspresso 6.
PAGE 100
Belgeler • FCC, CE, WHQL • ErP/EuP için hazır (ErP/EuP için hazır güç beslemesi gereklidir) * Detaylı ürün bilgisi için, lütfen web sitemizi ziyaret edin: http://www.asrock.com Lütfen, BIOS ayarlarını düzenleme, Bağımsız Hız Aşırtma Teknolojinin uygulanması ya da üçüncü kişilerin hız aşırtma araçlarının kullanılması da dahil olmak üzere tüm hız aşırtma işlemlerinin belirli bir risk taşıdığını unutmayın.
PAGE 101
B85iCafe4 1.3 Bağlantı Teli Kurulumu Çizim, bağlantı tellerinin kurulumunu göstermektedir. Tel kapağı, pimlerin üzerine yerleştirildiğinde, tel "Kısa" olur. Pimlerin üzerinde tel kapağı bulunmadığında, tel "Kısa" olur. Çizim, pin1 ve pin2 alanları "Kısa" olan ve bu iki pim üzerinde bir bağlantı teli kapağı bulunan 3-pin bağlantı telini göstermektedir. Varsayılan CMOS'u Temizle Türkçe CMOS'u Temizle Bağlantı Teli *(CLRCMOS1) (bkz. sf.1, No. 26) CLRCMOS1, CMOS verilerini temizlememizi sağlar.
PAGE 102
1.4 Ekli Bağlantılar ve Bağlayıcılar Ekli bağlantılar ve bağlayıcılar bağlantı teli değildir. Bağlantı teli kapaklarını bu bağlantı ve bağlayıcılar üzerine yerleştirmeyin. Bağlantı teli kapaklarının bağlantılar ile bağlayıcılar üzerine yerleştirilmesi, anakarta kalıcı hasar verebilir. Sistem Paneli Bağlantısı (9-pin PANEL1) (bkz sf.1, No. 17) Güç anahtarını bağlayın, kasa üzerindeki anahtar ile sistem durumu belirtecini aşağıdaki pim düzenine göre sıfırlayın.
PAGE 103
B85iCafe4 Seri ATA2 Bağlayıcıları (SATA_5: bkz. sf.1, No. 11) (SATA_6: bkz. sf.1, No. 12) Bu iki SATA2 bağlayıcısı, veri aktarım hızı 3,0 Gb/ sn'ye kadar olan dahili depolama aygıtları için tasarlanmış SATA veri kablolarını destekler. SATA_4 SATA_2 Bu dört SATA3 bağlayıcısı, veri aktarım hızı 6,0 Gb/sn’ye kadar olan dahili depolama aygıtları için tasarlanmış SATA veri kablolarını destekler. Türkçe SATA_3 SATA_1 Seri ATA3 Bağlayıcıları (SATA_1: bkz. sf.1, No. 15) (SATA_2: bkz. sf.1, No.
PAGE 104
Ön Panel Ses Bağlantısı (9-pin HD_AUDIO1) (bkz. sf.1, No. 24) Bu bağlantı, ses aygıtlarının ön ses paneline bağlanması içindir. Türkçe 1. Yüksek Tanımlı Ses, Jak Algılama özelliğini destekler, ancak bu işlevin düzgün çalışabilmesi için kasa üzerindeki panel kablosunun HDA işlevini desteklemesi gerekmektedir. Sisteminizi kurarken, lütfen kılavuzumuzdaki talimatlar ile kasa kılavuzundaki talimatları izleyin. 2.
PAGE 105
B85iCafe4 CPU Fan Bağlayıcıları (4-pin CPU_FAN1) (bkz sf.1, No. 3) (3-pin CPU_FAN2) (bkz sf.1, No. 4) ATX Güç Bağlayıcısı (24-pin ATXPWR1) (bkz. sf.1, No. 7) +12V GND PWR_FAN_SPEED FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND GND +12V CPU_FAN_SPEED 12 24 1 13 Bu anakart, 4-Pin CPU fan (Sessiz Fan) bağlayıcısı sağlamaktadır. 3-Pin CPU fan bağlamak istiyorsanız, lütfen Pin 1-3'ü kullanın. Bu anakart, 24-pin ATX güç bağlayıcısı sağlamaktadır.
PAGE 106
Yazdırma Bağlantı Noktası Bağlantısı (25-pin LPT1) (bkz. sf.1, No. 22) Türkçe 104 AFD# ERROR# PINIT# SLIN# GND 1 SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# Bu, yazıcı aygıtların uyumlu bir şekilde takılmasını sağlayan bir yazdırma bağlantı noktası arabirimidir.
PAGE 107
B85iCafe4 1 개요 ASRock B85iCafe4 마더보드를 구입해 주셔서 감사합니다 . 이 마더보드는 ASRock 의 일관되고 엄격한 품질관리 하에 생산되어 신뢰성이 우수합니다 . 품질과 내구성 에 대한 ASRock 의 기준에 부합하는 우수한 성능과 견고한 설계를 제공합니다 . 마더보드 규격과 BIOS 소프트웨어를 업데이트할 수도 있기 때문에 , 이 문서의 내 용은 예고 없이 변경될 수 있습니다 . 이 설명서가 변경될 경우 , 업데이트된 버전은 ASRock 의 웹사이트에서 추가 통지 없이 제공됩니다 . 이 마더보드와 관련하여 기 술적 지원이 필요한 경우 , 당사의 웹사이트를 방문하여 사용 중인 모델에 대한 구체 적 정보를 구하십시오 . ASRock 의 웹사이트에서는 최신 VGA 카드와 CPU 지원 목 록도 찾을 수 있습니다 . ASRock 웹사이트 http://www.asrock.com. • • • • • 한국어 1.
PAGE 108
1.2 규격 한국어 106 플랫폼 • ATX 폼 팩터 • 모든 솔리드 콘덴서 구조 CPU • LGA1150 패키지로 제공되는 4 세대 Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron® 지원 • Digi 전원 구조 • 6 개 전원 위상 구조 • Intel® Turbo Boost 2.0 기술 지원 칩세트 • Intel® B85 • Intel® Small Business Advantage 2.0 지원 메모리 • • • • 확장 슬롯 • PCI Express 3.0 x16 슬롯 1 개 • PCI Express 2.0 x1 슬롯 2 개 • PCI 슬롯 3 개 그래픽 • Intel® HD 그래픽스 빌트 - 인 비주얼과 VGA 출력은 GPU 통합 프로세서로만 지원할 수 있습니다 .
PAGE 109
B85iCafe4 • DVI-D 지원 ( 최대 해상도 1920x1200 @ 60Hz) • D-Sub 지원 ( 최대 해상도 1920x1200 @ 60Hz) • Auto Lip Sync, Deep Color (12bpc), xvYCC 및 HBR (High Bit Rate Audio)(HDMI 포함 ) 지원 (HDMI 호환 모니터 필요 ) • DVI-D 및 HDMI 포트를 이용한 HDCP 기능 지원 • DVI-D 및 HDMI 포트를 이용한 Full HD 1080p Blu-ray (BD) 재생 지원 오디오 • 콘텐츠 보호를 이용한 7.
PAGE 110
• • • • • • • • • • • • • IR 헤더 1 개 인쇄 포트 헤더 1 개 COM 포트 헤더 1 개 전원 LED 헤더 1 개 CPU 팬 커넥터 2 개 (1 x 4 핀 , 1 x 3 핀 ) 섀시 팬 커넥터 2 개 (1 x 4 핀 , 1 x 3 핀 ) 전원 팬 커넥터 1 개 (3 핀 ) 24 핀 ATX 전원 커넥터 1 개 8 핀 12V 전원 커넥터 1 개 전면 패널 오디오 커넥터 1 개 SPDIF 출력 커넥터 1 개 USB 2.0 헤더 2 개 (USB 2.0 포트 4 개 지원 ) USB 3.0 헤더 1 개 (USB 3.0 포트 2 개 지원 ) BIOS 기능 • • • • 다국어 GUI 지원을 제공하는 64Mb AMI UEFI 적합형 BIOS ACPI 1.1 준수 웨이크 업 이벤트 SMBIOS 2.3.1 지원 CPU, DRAM, PCH 1.05V, 전압 다중 조정 지원 CD • 드라이버 , 유틸리티 , 백신 소프트웨어 ( 시험판 ), CyberLink MediaEspresso 6.
PAGE 111
B85iCafe4 BIOS 설정을 조정하거나 Untied Overclocking Technology 를 적용하거나 타업체의 오버클로킹 도구를 사용하는 것을 포함하는 오버클로킹에는 어느 정도의 위험이 따른다는 것을 유념하십시오 . 오버클로킹은 시스템 안정성에 영향을 주거나 심지 어 시스템의 구성 요소와 장치에 손상을 입힐 수도 있습니다 . 오버클로킹은 사용자 스스로 위험과 비용을 감수하고 해야 합니다 . 당사는 오버클로킹에 의해 발생할 수 있는 손상에 대해서 책임이 없습니다 . 한국어 제한 때문에 실제 메모리 크기는 Windows® 32 비트 운영체제 하의 시스템 사용을 위한 예비 메모리용 4GB 보다 더 적을 수 있습니다 . Windows® 64 비트 운영체제에 는 그러한 제한이 없습니다 . ASRock XFast RAM 을 사용하여 Windows® 가 사용 할 수 없는 메모리를 이용할 수 있습니다 .
PAGE 112
1.3 점퍼 설정 그림은 점퍼를 어떻게 설정하는지 보여줍니다 . 점퍼 캡을 핀에 씌우면 점퍼가 “단 락”됩니다 . 점퍼 캡을 핀에 씌우지 않으면 점퍼가 “단선”됩니다 . 그림은 3 핀 점 퍼를 보여주며 핀 1 과 핀 2 는 점퍼 캡을 씌울 때 “단락”됩니다 . Clear CMOS 점퍼 (CLRCMOS1) (1 페이지 , 26 번 항목 참조 ) 기본값 Clear CMOS 한국어 CLRCMOS1 을 사용하여 CMOS 에 저장된 데이터를 지울 수 있습니다 . 시스 템 파라미터를 지우고 기본 설정으로 초기화하려면 컴퓨터를 끄고 전원 코 드를 전원공급장치에서 빼십시오 . 15 초 동안 기다린 후 점퍼 캡을 사용하여 CLRCMOS1 의 핀 2 와 핀 3 을 5 초 동안 단락시키십시오 . 그러나 BIOS 업데이 트 직후에는 CMOS 를 삭제하지 마십시오 .
PAGE 113
B85iCafe4 1.4 온보드 헤더 및 커넥터 온보드 헤더와 커넥터는 점퍼가 아닙니다 . 점퍼 캡을 온보드 헤더와 커넥터에 씌우 지 마십시오 . 점퍼 캡을 온보드 헤더와 커넥터에 씌우면 마더보드가 영구적으로 손 상됩니다 . 섀시의 전원 스위치 , 리 셋 스위치 , 시스템 상태 표시등을 아래의 핀 할 당에 따라 이 헤더에 연 결합니다 . 케이블을 연 결하기 전에 양극 핀과 음극 핀을 기록합니다 . 한국어 시스템 패널 헤더 (9 핀 PANEL1) (1 페이지 , 17 번 항목 참조 ) PWRBTN( 전원 스위치 ): 섀시 전면 패널의 전원 스위치에 연결합니다 . 전원 스위치를 이용해 시스템을 끄는 방법을 구성할 수 있습니다 . RESET( 리셋 스위치 ): 섀시 전면 패널의 전원 스위치에 연결합니다 . 컴퓨터가 정지하고 정상적 재시작을 수행하지 못할 경우 리셋 스위치를 눌러 컴퓨터를 재시작합니다 . PLED( 시스템 전원 LED): 섀시 전면 패널의 전원 상태 표시등에 연결합니다 .
PAGE 114
시리얼 ATA2 커넥터 (SATA_5: (1 페이지 , 11 번 항목 참조 ) (SATA_6: (1 페이지 , 12 번 항목 참조 ) 이들 두 개의 SATA2 커 넥터는 최대 3.0 Gb/s 데 이터 전송 속도를 제공 하는 내부 저장 장치용 SATA 데이터 케이블을 지원합니다 . 112 SATA_3 SATA_4 SATA_1 SATA_2 한국어 시리얼 ATA3 커넥터 (SATA_1: 1페이지, 15 번 항목 참조) (SATA_2: (1 페이지 , 14 번 항목 참조 ) (SATA_3: (1 페이지 , 10 번 항목 참조 ) (SATA_4: 1페이지, 13 번 항목 참조 ) SATA_6 시스템 전원 상태를 나타 내려면 섀시 전원 LED 를 이 헤더에 연결하십시 오. SATA_5 전원 LED 헤더 (3 핀 PLED1) (1 페이지 , 16 번 항목 참조 ) 이들 4 개의 SATA3 커 넥터는 최대 6.
PAGE 115
B85iCafe4 전면 패널 오디오 헤더 (9 핀 HD_AUDIO1) (1 페이지 , 24 번 항목 참조 ) 이 헤더는 오디오 장치 를 전면 오디오 패널에 연결하는 데 사용됩니 다. 섀시 스피커 헤더 (4 핀 SPEAKER1) (1 페이지 , 9 번 항목 참조 ) 섀시 스피커를 이 헤더 에 연결하십시오 . SPDIF 출력 커넥터 (2 핀 SPDIF_OUT1) (1 페이지 , 27 번 항목 참조 ) HDMI VGA 카드의 SPDIF_OUT 커넥터를 케이블로 이 헤더에 연결 하십시오 . 섀시 및 전원 팬 커넥터 (4 핀 CHA_FAN1) (1 페이지 , 18 번 항목 참조 ) (3 핀 CHA_FAN2) (1 페이지 , 19 번 항목 참조 ) GND +12V FAN_SPEED FAN_SPEED_CONTROL 한국어 111 고음질 오디오는 잭 감지를 지원하지만 올바르게 작동하려면 섀시의 패널 와이어 가 HDA 를 지원해야 합니다 .
PAGE 116
(3 핀 PWR_FAN1) (1 페이지 , 1 번 항목 참조 ) CPU 팬 커넥터 (4 핀 CPU_FAN1) (1 페이지 , 3 번 항목 참조 ) (3 핀 CPU_FAN2) (1 페이지 , 4 번 항목 참조 ) 한국어 ATX 전원 커넥터 (24 핀 ATXPWR1) (1 페이지 , 7 번 항목 참조 ) 114 +12V PWR_FAN_SPEED GND FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND GND +12V CPU_FAN_SPEED 12 24 1 13 이 마더보드에는 4 핀 CPU 팬 ( 저소음 팬 ) 커 넥터가 탑재되어 있습니 다 . 3 핀 CPU 팬을 연결 하려는 경우 핀 1-3 에 연 결하십시오 . 이 마더보드에는 24 핀 ATX 전원 커넥터가 탑 재되어 있습니다 . 20 핀 ATX 전원공급장치를 사 용하려면 핀 1 과 핀 13 을 따라 연결하십시오 .
PAGE 117
B85iCafe4 GND SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# 프린터 장치의 간편한 연결을 가능하게 하는 인쇄 포트 케이블용 인 터페이스입니다 .
PAGE 118
1 B85iCafe4 BIOS 日本語 VGA CPU http://www.asrock.com. 1.
PAGE 119
B85iCafe4 1.2 • ATX • • LGA1150 4 i3 / Xeon® / Pentium® / Celeron® • • 6 • Intel® 2.0 • Intel® B85 • Intel® Intel® CoreTM i7 / i5 / 2.0 • DDR3 • 4 x DDR3 DIMM • DDR3 1600/1333/1066 ECC • • Intel® 日本語 CPU 3 2GB X MP 1.3/1.2 • 1 x PCI Express 3.0 x16 • 2 x PCI Express 2.0 x1 • 3 x PCI • Intel®HD VGA GPU • Intel®HD AVC MVC (S3D) MPEG-2 HW 1 Intel® Quick Sync Video Intel® InTruTM 3D Intel® HD TM Intel® Intel® HD 4400/4600 • 5.0 DirectX 11.
PAGE 120
• DVI-D • D-Sub 1920x1200 @60Hz 1920x1200 @60Hz • HDMI HDMI 12bpc • DVI-D • DVI-D HDMI HDMI xvYCC HBR HDCP HD 1080p (BD) • 7.1 CH HD Realtek ALC892 • • TI® NE5532 600 日本語 LAN • • • • • • I/O 118 • • • • • • • • • PCIE x1 LAN 10/100/1000 Mb/ Realtek RTL8111G LAN 802.3az PXE 1 x PS/2 1 x PS/2 1 x D-Sub 1 x DVI-D 1 x HDMI 1 x SPDIF 4 x USB 2.0 2 x USB 3.0 LED 1 x R LED • HD / J-45 LAN ACT/LINK LED / / • 4 x SATA3 6.0 Gb/ NCQ AHCI • 2 x SATA2 3.
PAGE 121
B85iCafe4 • 1 x IR • 1x BIOS 1 x COM 1x LED 2 x CPU 2x 1x 1 x 24 ATX 1x8 12V 1x 1 x SPDIF Out 2 x USB 2.0 1 x USB 3.0 1x4 1x4 3 4 2 USB 2.0 USB 3.0 • GUI • ACPI 1.1 • SMBIOS 2.3.1 • CPU DRAM PCH 1.05V CD 1x3 1x3 日本語 • • • • • • • • • • • 64Mb AMI UEFI Legal BIOS • CyberLink MediaEspresso 6.5 Google Chrome Start8 • CPU/ • CPU/ • CPU/ • CPU/ • OS / CPU + 12V +5V +3.3V CPU Vcore • Microsoft® Windows® 8 / 8 64 /7/76 4 • FCC CE WHQL • ErP/EuP Ready ErP/EuP ready * http://www.asrock.
PAGE 122
BIOS Windows® 32 4GB 64 Windows® 日本語 120 W indows® XFast RAM
PAGE 123
B85iCafe4 1.3 3 2 日本語 1 CMOS (CLRCMOS1) p.1 No.
PAGE 124
1.4 9 p.1 No.
PAGE 125
B85iCafe4 LED 3 PLED1 p.1 No. 16 SATA_6 SATA_5 SATA2 3.0 Gb/ SATA_4 SATA_2 4 SATA3 6.0 Gb/ 日本語 SATA_3 ATA3 SATA_1: p.1 No. 15 SATA_2: p.1 No. 14 SATA_3: p.1 No. 10 SATA_4: p.1 No. 13 2 SATA SATA_1 ATA2 SATA_5: p.1 No. 11 SATA_6: p.1 No. 12 LED SATA USB 2.0 9 USB4_5 p.1 No. 21 9 USB6_7 p.1 No. 20 I/O 2.0 USB 3.0 19 USB3_2_3 p.1 No. 8 I/O 3.0 4 USB 2 USB 2.0 2 2 USB 1 USB 3.
PAGE 126
9 HD_AUDIO1 p.1 No. 24 111 HDA 222 AC 97 日本語 A. Mic_IN (MIC) MIC2_L B. Audio_R (RIN) OUT2_R Audio_L (LIN) C. (GND) (GND) D. MIC_RET OUT_RET HD E. OUT2_L AC 97 Realtek FrontMic 4 SPEAKER1 p.1 No. 9 SPDIF Out 2 SPDIF_OUT1 p.1 No. 27 4 CHA_FAN1 p.1 No. 18 3 CHA_FAN2 p.1 No.
PAGE 127
B85iCafe4 PWR_FAN1 p.1 No. 1 CPU 4 CPU_FAN1 p.1 No. 3 +12V PWR_FAN_SPEED GND 4 FAN_SPEED_CONTROL CPU CPU_FAN_SPEED +12V GND 3 3 CPU_FAN2 p.1 No. 4 ATX 24 ATXPWR1 p.1 No. 7 GND +12V CPU_FAN_SPEED 12 CPU 1-3 日本語 3 24 24 ATX 20 ATX 1 1 ATX12V 8 ATX12V1 p.1 No. 2 13 13 8 ATX12V 4 ATX 1 5 5 IR1 p.1 No. 25 COM1 9 COM1 p.1 No.
PAGE 128
25 LPT1 p.1 No.
PAGE 129
B85iCafe4 1 简介感谢您购买 ASRock B85iCafe4 主板，这是按照 ASRock 一贯严格质量控制标准生产的性能可靠的主板。它提供符合 ASRock 质量和耐久性承诺的精良设计和卓越性能。简体中文由于主板规格和 BIOS 软件可能已更新，因此，本文档的内容可能会随时更改，恕不另行通知。如果本文档有任何修改，则更新的版本将发布在 ASRock 网站上，我们不会另外进行通知。如果您需要与此主板相关的技术支持，请访问我们的网站以具体了解所用型号的信息。您也可以在 ASRock 网站上找到最新 VGA 卡和 CPU 支持列表。ASRock 网站 http://www.asrock.com。 1.
PAGE 130
1.2 规格简体中文平台 • ATX 规格尺寸 • 全固态电容 CPU • 支持 LGA1150 封装第 4 代 Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron® • Digi Power（帝捷）设计 • 6 电源相设计 • 支持 Intel® Turbo Boost 2.0 技术芯片集 • Intel® B85 • 支持 Intel® Small Business Advantage 2.0 内存 • • • • 扩充槽 • 1 x PCI Express 3.0 x16 槽 • 2 x PCI Express 2.
PAGE 131
B85iCafe4 音频 • 具有内容保护功能的 7.1 CH 高清音频（Realtek ALC892 音频编解码器） • 优质 Blu-ray 音频支持 • TI® NE5532 （支持最高 600 Ohms 优质耳放） LAN • • • • • • 后面板 I/O • • • • • • • • • 简体中文 • 支持 DVI-D，60Hz 时最大分辨率达 1920x1200 • 支持 D-Sub，60Hz 时最大分辨率达 1920x1200 • 通过 HDMI（需要符合规格的 HDMI 监视器）支持 Auto Lip Sync、Deep Color (12bpc), xvYCC 和 HBR（高位速率音频） • 通过 DVI-D and HDMI 端口支持 HDCP 功能 • 通过 DVI-D 和 HDMI 端口支持全高清 1080p Blu-ray (BD) 播放。 PCIE x1 Gigabit LAN 10/100/1000 Mb/s Realtek RTL8111G 支持 Wake-On-LAN（网上唤醒）支持网路綫侦测功能支持高能效以太网 802.
PAGE 132
• • • • • • • • • • • • • 1 x IR 接脚 1 x 打印端口接脚 1 x COM 端口接脚 1 x 电源 LED 接脚 2 x CPU 风扇接口 (1 x 4 针 , 1 x 3 针 ) 2 x 机箱风扇接口 (1 x 4 针 , 1 x 3 针 ) 1 x 电源风扇接口 (3 针 ) 1 x 24 针 ATX 电源接口 1 x 8 针 12V 电源接口 1 x 前面板音频接口 1 x SPDIF 输出接口 2 x USB 2.0 接脚（支持 4 个 USB 2.0 端口） 1 x USB 3.0 接脚（支持 2 个 USB 3.0 端口） BIOS 功能特点 • • • • 64Mb AMI UEFI Legal BIOS，具有多语言 GUI 支持 ACPI 1.1 兼容唤醒事件 SMBIOS 2.3.1 支持 CPU、DRAM, PCH 1.05V 电压多次调整（Voltage Multiadjustment）支持光盘 • 驱动程序、实用程序、防病毒软件（试用版）、CyberLink MediaEspresso 6.
PAGE 133
B85iCafe4 须认识到超频会有一定风险，包括调整 BIOS 设置，应用“自由超频技术”，或使用第三方超频工具。超频可能会影响到系统的稳定性，甚至对系统的组件和设备造成损坏。执行这项工作您应自担风险和自己承担费用。我们对由于超频而造成的损坏概不负责。简体中文由于限制原因，实际内存容量可能会小于 4GB，以保留给 Windows® 32-bit 操作系统下的系统使用。Windows® 64-bit 操作系统没有此类限制。您可以使用 ASRock XFast RAM 来利用 Windows® 不能使用的内存。 131
PAGE 134
1.
PAGE 135
B85iCafe4 1.
PAGE 136
到此接脚以指示系统电源状态。串行 ATA2 接口 (SATA_5: 见第 1 页，第 11 个） (SATA_6: 见第 1 页，第 12 个）这两个 SATA2 接口支持最高 3.0 Gb/s 数据传输速率的内部存储设备的 SATA 数据线。 134 SATA_3 SATA_4 SATA_1 SATA_2 简体中文串行 ATA3 接口 (SATA_1: 见第 1 页，第 15 个） (SATA_2: 见第 1 页，第 14 个） (SATA_3: 见第 1 页，第 10 个） (SATA_4: 见第 1 页，第 13 个） SATA_6 请将机箱电源 LED 连接 (3 针 PLED1) （见第 1 页，第 16 个） SATA_5 电源 LED 接脚这四个 SATA3 接口支持最高 6.0 Gb/s 数据传输速率的内部存储设备的 SATA 数据线。 USB 2.0 接脚 (9 针 USB4_5) （见第 1 页，第 21 个） (9 针 USB6_7) （见第 1 页，第 20 个）除 I/O 面板上的四个 USB 2.
PAGE 137
B85iCafe4 前面板音频接脚 (9 针 HD_AUDIO1) （见第 1 页，第 24 个）此接脚用于将音频设备连接到前音频面板。机箱扬声器接脚 (4 针 SPEAKER1) 见第 1 页，第 9 个）请将机箱扬声器连接到此接脚。 SPDIF 输出接口 (2 针 SPDIF_OUT1) 见第 1 页，第 27 个）请使用线缆将 HDMI VGA 卡的 SPDIF_OUT 接口连接到此接脚。机箱和电源风扇接口 (4 针 CHA_FAN1) 见第 1 页，第 18 个） (3 针 CHA_FAN2) 见第 1 页，第 19 个） GND +12V FAN_SPEED FAN_SPEED_CONTROL 简体中文 111 高清音频支持插孔感测，但机箱上的面板连线必须支持 HDA 才能正常工作。请按照我们的手册和机箱手册的说明安装系统。 222 如果您使用 AC’97 音频面板，请按照以下步骤安装到前面板音频接脚： A. 将 Mic_IN (MIC) 连接到 MIC2_L.
PAGE 138
(3 针 PWR_FAN1) 见第 1 页，第 1 个） CPU 风扇接口 (4 针 CPU_FAN1) 见第 1 页，第 3 个）简体中文 (3 针 CPU_FAN2) 见第 1 页，第 4 个） ATX 电源接口 (24 针 ATXPWR1) （见第 1 页，第 7 个） 136 +12V PWR_FAN_SPEED GND FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND 此主板提供 4 针 CPU 风扇（静音风扇）接口。如果您打算连接 3 针 CPU 风扇，请将它连接到脚 1-3。 GND +12V CPU_FAN_SPEED 12 24 1 13 此主板提供 24 针 ATX 电源接口。要使用 20 针 ATX 电源，请沿针脚 1 和针脚 13 插接它。 ATX 12V 电源接口 (8 针 ATX12V1) （见第 1 页，第 2 个）此主板提供 8 针 ATX 12V 电源接口。要使用 4 针 ATX 电源，请沿针脚 1 和针脚 5 插接它。红外线模块接脚 (5 针 IR1) （见第 1 页，第 25 个）此接脚
PAGE 139
B85iCafe4 (25 针 LPT1) ( 见第 1 页，第 22 个） AFD# ERROR# PINIT# SLIN# 这是一个打印端口线缆 GND 1 接口，通过它可以方便地连接到打印机设备。 SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# 简体中文打印端口接脚 137
PAGE 140
電子信息產品污染控制標示依據中國發布的「電子信息產品污染控制管理辦法」及 SJ/T 11364-2006「電子信息產品污染控制標示要求」，電子信息產品應進行標示，藉以向消費者揭露產品中含有的有毒有害物質或元素不致發生外洩或突變從而對環境造成污染或對人身、財產造成嚴重損害的期限。依上述規定，您可于本產品之印刷電路板上看見圖一之標示。圖一中之數字為產品之環保使用期限。由此可知此主板之環保使用期限為 10 年。简体中文圖一有毒有害物質或元素的名稱及含量說明若您慾了解此產品的有毒有害物質或元素的名稱及含量說明，請參照以下表格及說明。有害物質或元素部件名稱鉛 (Pb) 鎘 (Cd) 汞 (Hg) 六价鉻 (Cr(VI)) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 印刷電路板 X O O O O O 及電子組件外部信號連 X O O O O O 接頭及線材 O: 表示該有毒有害物質在該部件所有均質材料中的含量均在 SJ/T 11363-2006 標準規定的限量要求以下。 X: 表示該有毒有害物質至少在該部件的某一均質材料中的含量超出 SJ/T 11363-2
PAGE 141
B85iCafe4 1 簡介感謝您購買 ASRock B85iCafe4 主機板，本主機板經 ASRock 嚴格品管製作，是一套讓人信賴的可靠產品。本產品採耐用設計所展現的優異效能，完全符合 ASRock 對品質及耐用度的承諾。繁體中文由於主機板規格及 BIOS 軟體可能會更新，所以本文件內容如有變更，恕不另行通知。如本文件有任何修改，可至 ASRock 網站逕行取得更新版本，不另外通知。若您需要與本主機板相關的技術支援，請上我們的網站瞭解有關您使用機型的特定資訊。您也可以在 ASRock 網站找到最新的 VGA 卡及 CPU 支援清單。ASRock 網站 http://www.asrock.com. 1.
PAGE 142
1.2 規格 • ATX 尺寸 • 全固態電容設計 CPU • 支援第 4 代 Intel® CoreTM i7 / i5 / i3 / Xeon® / Pentium® / Celeron® (LGA1150 封裝 ) • 數位電源設計 • 6 電源相位設計 • 支援 Intel® Turbo Boost 2.0 技術晶片組 • Intel® B85 • 支援 Intel® Small Business Advantage 2.0 記憶體 • • • • 擴充插槽 • 1 x PCI Express 3.0 x16 插槽 • 2 x PCI Express 2.
PAGE 143
B85iCafe4 音訊 • 7.1 CH HD 音訊含內容保護（Realtek ALC892 音訊轉碼器）功能 • 高階藍光音訊支援 • TI® NE5532 ( 支援最高 600 Ohms 的 Premium Headset Amplifier) LAN • • • • • • PCIE x1 Gigabit LAN 10/100/1000 Mb/s Realtek RTL8111G 支援網路喚醒支援網路線偵測功能支援 Energy Efficient Ethernet 802.3az 支援 PXE 後面板 I/O • • • • • • • • • 1 x PS/2 滑鼠連接埠 1 x PS/2 鍵盤連接埠 1 x D-Sub 連接埠 1 x DVI-D 連接埠 1 x HDMI 連接埠 1 x 光纖 SPDIF 輸出連接埠 4 x USB 2.0 連接埠 2 x USB 3.
PAGE 144
• • • • • • • • • • • • • 1 x IR 標頭 1 x 列印連接埠標頭 1 x COM 連接埠標頭 1 x 電源 LED 標頭 2 x CPU 風扇接頭 (1 x 4-pin、1 x 3-pin) 2 x 機殼風扇接頭 (1 x 4-pin、1 x 3-pin) 1 x 電源風扇接頭 (3-pin) 1 x 24 pin ATX 電源接頭 1 x 8 pin 12V 電源接頭 1 x 前面板音訊接頭 1 x SPDIF 輸出接頭 2 x USB 2.0 標頭（支援 4 USB 2.0 連接埠） 1 x USB 3.0 標頭（支援 2 USB 3.0 連接埠） BIOS 功能 • • • • 64Mb AMI UEFI Legal BIOS 含多語 GUI 支援 ACPI 1.1 符合喚醒自動開機支援 SMBIOS 2.3.1 CPU、DRAM、PCH 1.05V 電壓多重調整支援 CD • 驅動程式、公用程式、防毒軟體（試用版）、CyberLink MediaEspresso 6.
PAGE 145
B85iCafe4 * 如需產品詳細資訊，請上我們的網站： http://www.asrock.
PAGE 146
1.
PAGE 147
B85iCafe4 1.
PAGE 148
Serial ATA2 接頭 (SATA_5: 請參閱第 1 頁，編號 11) (SATA_6: 請參閱第 1 頁，編號 12) 這兩組 SATA2 接頭皆支援內部儲存裝置的 SATA 資料纜線，最高可達 3.0 Gb/s 資料傳輸率。 146 SATA_3 SATA_4 SATA_2 Serial ATA3 接頭 (SATA_1: 請參閱第 1 頁，編號 15） (SATA_2: 請參閱第 1 頁，編號 14) (SATA_3: 請參閱第 1 頁，編號 10) (SATA_4: 請參閱第 1 頁，編號 13） SATA_6 接至此標頭，以指示系統的電源狀態。 SATA_5 請將機殼電源 LED 連 (3-pin PLED1) （請參閱第 1 頁，編號 16） SATA_1 繁體中文電源 LED 標頭這四組 SATA3 接頭皆支援內部儲存裝置的 SATA 資料纜線，最高可達 6.0 Gb/s 資料傳輸率。 USB 2.
PAGE 149
B85iCafe4 本標頭適用於連接音訊裝置至前面板音訊。繁體中文前面板音訊標頭 (9-pin HD_AUDIO1) （請參閱第 1 頁，編號 24） 111 高解析度音訊支援智慧型音效介面偵測 (Jack Sensing)，但機殼上的面板線必須支援 HDA 才能正確運作。請依本手冊及機殼手冊說明安裝系統。 222 若您使用 AC’97 音訊面板，請按照以下步驟安裝至前面板音訊標頭： A. 將 Mic_IN (MIC) 連接至 MIC2_L。 B. 將 Audio_R (RIN) 連接至 OUT2_R 且將 Audio_L (LIN) 連接至 OUT2_L。 C. 將接地 (GND) 連接至接地 (GND)。 D. MIC_RET 及 OUT_RET 僅供 HD 音訊面板使用。您不需要在 AC’97 音訊面板上連接。 E.
PAGE 150
(3-pin PWR_FAN1) +12V GND PWR_FAN_SPEED （請參閱第 1 頁，編號 1） CPU 風扇接頭 (4-pin CPU_FAN1) （請參閱第 1 頁，編號 3）繁體中文 (3-pin CPU_FAN2) （請參閱第 1 頁，編號 4） ATX 電源接頭 (24-pin ATXPWR1) （請參閱第 1 頁，編號 7） 148 FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND GND +12V CPU_FAN_SPEED 12 24 1 13 本主機板配備 4-Pin CPU 風扇（靜音風扇）接頭。若您計畫連接 3-Pin CPU 風扇，請接至 Pin 1-3。本主機板配備一組 24-pin ATX 電源接頭。若要使用 20-pin ATX 電源供應器，請插入 Pin 1 及 Pin 13。 ATX 12V 電源接頭 (8-pin ATX12V1) （請參閱第 1 頁，編號 2）本主機板配備一組 8-pin ATX 12V 電源接頭。若要使用 4-pin ATX 電源供應器，請插入 Pin 1
PAGE 151
B85iCafe4 (25-pin LPT1) ( 請參閱第 1 頁，編號 22）1 AFD# ERROR# PINIT# SLIN# 這是供列印連接埠纜線 GND 使用的介面，可方便印表機裝置連線。 SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# 繁體中文列印連接埠標頭 149
PAGE 152
1 Pendahuluan Bahasa Indonesia Terima kasih telah membeli motherboard ASRock B85iCafe4, yakni motherboard andal yang diproduksi di bawah kendali mutu ketat yang sejalan dengan ASRock. Motherboard ini memberikan performa luar biasa dengan desain canggih yang meneguhkan komitmen ASRock terhadap kualitas dan ketahanan. Karena spesifikasi motherboard dan perangkat lunak BIOS dapat di-update, maka isi dokumentasi ini akan berubah sewaktu-waktu tanpa pemberitahuan sebelumnya.
PAGE 153
B85iCafe4 Platform • Bentuk dan Ukuran ATX • Desain Kapasitor Solid CPU • Mendukung Intel® CoreTM i7 / i5 / i3 Generasi Ke-4 / Xeon® / Pentium® / Celeron® dalam Paket LGA1150 • Desain Digi Power • Desain 6 Fase Daya • Mendukung Teknologi Intel® Turbo Boost 2.0 Chipset • Intel® B85 • Mendukung Intel® Small Business Advantage 2.
PAGE 154
Bahasa Indonesia • Mendukung DVI-D dengan resolusi maksimum hingga 1920x1200 @ 60Hz • Mendukung D-Sub dengan resolusi maksimum hingga 1920x1200 @ 60Hz • Mendukung Auto Lip Sync, Deep Color (12bpc), xvYCC, dan HBR (High Bit Rate Audio) dengan HDMI (memerlukan monitor HDMI yang kompatibel) • Mendukung fungsi HDCP dengan port DVI-D dan HDMI • Mendukung pemutaran Full HD 1080p Blu-ray (BD) dengan port DVI-D dan HDMI Audio • Audio HD 7.
PAGE 155
B85iCafe4 • • • • • • • • • • • • • 1 x Header IR 1 x Header port Cetak 1 x Header port COM 1 x Kepala LED daya 2 x Konektor kipas CPU (1 x 4-pin, 1 x 3-pin) 2 x Konektor kipas chassis (1 x 4-pin, 1 x 3-pin) 1 x Konektor kipas daya (3-pin) 1 x Konektor daya ATX 24 pin 1 x Konektor daya 12V 8 pin 1 x Konektor audio panel depan 1 x Konektor SPDIF Out 2 x Header USB 2.0 (mendukung 4 port USB 2.0) 1 x Header USB 3.0 (mendukung 2 port USB 3.
PAGE 156
* Untuk informasi tentang produk rinci, kunjungi situs web kami: http://www.asrock.com Bahasa Indonesia Perlu diketahui, overclocking memiliki risiko tertentu, termasuk menyesuaikan pengaturan pada BIOS, menerapkan Teknologi Untied Overclocking, atau menggunakan alat overclocking pihak ketiga. Overclocking dapat mempengaruhi stabilitas sistem, atau bahkan dapat mengakibatkan kerusakan komponen dan perangkat sistem. Risiko dan biaya apapun menjadi tanggungan Anda.
PAGE 157
B85iCafe4 1.3 Konfigurasi Jumper Bahasa Indonesia Gambar menunjukkan cara mengkonfigurasi jumper. Bila penutup jumper diletakkan pada pin, maka jumper akan “Pendek”. Jika tidak ada penutup jumper yang diletakkan pada pin, maka jumper akan “Terbuka”. Gambar menunjukkan jumper 3-pin, yakni pin1 dan pin2 menjadi "Pendek" bila penutup jumper diletakkan pada 2 pin tersebut. Clear CMOS Jumper (CLRCMOS1) (lihat hal. 1, No. 26) Default Clear CMOS CLRCMOS1 memungkinkan Anda mengosongkan data di CMOS.
PAGE 158
1.4 Header dan Konektor Onboard Bahasa Indonesia Header dan konektor terpasang BUKANLAH jumper. JANGAN letakkan penutup jumper pada header dan konektor tersebut. Meletakkan penutup jumper pada header dan konektor akan mengakibatkan kerusakan permanen pada motherboard. Header Panel Sistem (PANEL1 9-pin) (lihat hal. 1, No. 17) Sambungkan switch daya, atur ulang indikator status sistem dan switch daya pada chassis ke header tersebut berdasarkan penetapan pin di bawah ini.
PAGE 159
Konektor Serial ATA2 (SATA_5: lihat hal. 1, No. 11) (SATA_6: lihat hal. 1, No. 12) Kedua konektor SATA2 ini mendukung kabel data SATA untuk perangkat penyimpanan internal dengan kecepatan transfer data hingga 3,0 Gb/s. SATA_3 SATA_4 SATA_1 SATA_2 Konektor Serial ATA3 (SATA_1: lihat hal. 1, No. 15) (SATA_2: lihat hal. 1, No. 14) (SATA_3: lihat hal. 1, No. 10) (SATA_4: lihat hal. 1, No. 13) SATA_6 Sambungkan LED daya chassis ke header ini untuk menunjukkan status daya sistem.
PAGE 160
Header Audio Panel Depan (HD_AUDIO1 9-pin) (lihat hal. 1, No. 24) Header ini untuk menyambungkan perangkat audio ke panel audio depan. Bahasa Indonesia 1. Audio Definisi Tinggi mendukung Sensor Soket, namun kabel panel pada chassis harus mendukung HDA agar berfungsi dengan benar. Ikuti petunjuk dalam panduan pengguna ini dan panduan pengguna chassis untuk menginstal sistem. 2. Jika Anda menggunakan panel audio AC’97, pasang ke header audio panel depan dengan melakukan langkah-langkah di bawah ini: A.
PAGE 161
B85iCafe4 Konektor Kipas CPU (CPU_FAN1 4-pin) (lihat hal. 1, No. 3) (CPU_FAN2 3-pin) (lihat hal. 1, No. 4) Konektor Daya ATX (ATXPWR1 24-pin) (lihat hal. 1, No. 7) +12V GND PWR_FAN_SPEED FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND GND +12V CPU_FAN_SPEED 12 24 1 13 Bahasa Indonesia (PWR_FAN1 3-pin) (lihat hal. 1, No. 1) Motherboard ini memberikan konektor kipas CPU 4-Pin (Kipas Hening). Jika Anda berencana untuk menyambungkan kipas CPU 3-Pin, sambungkan ke Pin 1-3.
PAGE 162
Header Port Cetak (LPT1 25-pin) (lihat hal. 1, No. 22) AFD# ERROR# PINIT# SLIN# GND 1 Bahasa Indonesia SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# 160 Ini adalah interface untuk kabel port cetak yang memungkinkan sambungan perangkat printer secara nyaman.
PAGE 163
Contact Information If you need to contact ASRock or want to know more about ASRock, you’re welcome to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer for further information. For technical questions, please submit a support request form at http://www.asrock.com/support/tsd.asp ASRock Incorporation 2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District, Taipei City 112, Taiwan (R.O.C.) ASRock EUROPE B.V.