Laptop User Manual

ManualsBrandsAspire Digital ManualsLaptop5332

Aspire 5732Z/5332

Service Guide

PRINTED IN TAIWAN

Service guide files and updates are available

on the ACER/CSD web; for more information,

please refer to http://csd.acer.com.tw

Summary of content (230 pages)

PAGE 1
Aspire 5732Z/5332 Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.
PAGE 2
Revision History Please refer to the table below for the updates made on Aspire 5732Z/5332 service guides.
PAGE 3
Copyright Copyright © 2009 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
PAGE 4
Conventions The following conventions are used in this manual: IV SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
PAGE 5
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
PAGE 6
VI
PAGE 7
Table of Contents System Specifications 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
Table of Contents Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Removing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Removing the Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 Removing the Left Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 Removing the Right Speaker Module . . . . . . . . . . . . . . . . . .
PAGE 9
Table of Contents Wireless Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 Thermal Unit Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 External Mouse Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 Other Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 Intermittent Problems . . . . . . . . .
PAGE 10
Table of Contents X
PAGE 11
Chapter 1 System Specifications Features Below is a brief summary of the computer’s many features: NOTE: Items denoted with a (*) are only available for select models. Operating System • Genuine Windows® Vista™* • Genuine Windows® 7™* Platform • Intel® Pentium® mobile processor* • Intel® Celeron® mobile processor* • Mobile Intel® GL40 Express Chipset • Acer InviLink™ 802.11b/g* • Acer InviLink™ Nplify™ 802.
PAGE 12
• High-definition audio support • MS-Sound compatible Dimensions and Weight • 372.3 (W) x 246.5 (D) x 26.8/39.6 (H) mm (14.4 x 10.8 x 1.1/1.5 inches) • 2.7 kg (6.0 lbs.) with 6-cell battery pack Communication • Integrated Acer Crystal Eye webcam* • Wireless • • Acer InviLink™ 802.11b/g* • Acer InviLink™ Nplify™ 802.11b/g/Draft-N LAN • Fast Ethernet; Wake-on-LAN ready Privacy control • BIOS user, supervisor, HDD passwords • Kensington lock slot Power subsystem • ACPI 3.0 • 48.
PAGE 13
• Chapter 1 Humidity (non-condensing): • Operating: 20% to 80% • Non-operating: 20% to 80% 3
PAGE 14
System Block Diagram page 4 EMC 1402 uPGA-478 Package (Socket P) page 4,5,6 FS B H_A#(3..35) LCD C onn. 667/800/1066MHz Clock Generator Thermal Sensor Intel Penryn Processor Fan Control ICS9LPRS387 page 4 page 16 H_D#(0..63) CRT Conn. page 17 page 18 Memory BUS(DDRII) Intel Cantiga Dual Channel BANK 0, 1, 2, 3 page 14,1 5 1.
PAGE 15
Your Acer Notebook tour After knowing your computer features, let us show you around your new computer. Front View No. Icon Item Description 1 Acer Crystal Eye webcam Web camera for video communication (for selected models). 2 Display screen Also called Liquid-Crystal Display (LCD), displays computer output. 3 Touchpad toggle Turns the internal touchpad on and off. Power button Turns the computer on and off.
PAGE 16
No. Icon Item Description 7 Click buttons (left and right) The left and right buttons function like the left and right mouse buttons. 8 Palmrest Comfortable support area for your hands when you use the computer. 9 HDD Indicates when the hard disk drive is active. Closed Front View 1 No. 1 2 2 Icon Item Description Power Indicates the computer's power status. Battery1 Indicates the computer's battery status. 1. Charging: The light shows amber when the battery is charging. 2.
PAGE 17
Rear View 1 No. Icon Item 1 Ventilation slots Description Enable the computer to stay cool, even after prolonged use. Left View 1 No. Icon 2 3 Item 4 5 Description 1 DC-in jack Connects to an AC adapter. 2 Ethernet (RJ-45) port Connects to an Ethernet 10/100-based network. 2 External display (VGA) port Connects to a display device (e.g. external monitor, LCD projector). 4 USB 2.0 ports Connect to USB 2.0 devices (e.g. USB mouse, USB camera).
PAGE 18
Right View 1 No. Item 2 34 5 Description 1 Optical drive Internal optical drive; accepts CDs or DVDs. 2 Optical disk access indicator Lights up when the optical drive is active. 3 Optical drive eject button Ejects the optical disk from the drive. 4 Emergency eject hole Ejects the optical drive tray when the computer is turned off. Note: Insert a paper clip into the emergency eject hole to eject the optical drive tray when the computer is off.
PAGE 19
No. Icon Item Description 3 Battery lock Locks the battery in position. 4 Hard disk bay Houses the computer's hard disk (secured with screws). 5 Memory compartment Houses the computer's main memory. 5 Ventilation slots and cooling fan Enable the computer to stay cool, even after prolonged use. Note: Do not cover or obstruct the fan opening.
PAGE 20
Indicators The computer has several easy-to-read status indicators. The front panel indicators are visible even when the computer cover is closed. Icon Function Description Power Indicates the computer's power status. Battery Indicates the computer's battery status. HDD Indicates when the hard disk drive is active. Num Lock Lights up when Num Lock is activated. Caps Lock Lights up when Caps Lock is activated. NOTE: 1. Charging: The light shows amber when the battery is charging. 2.
PAGE 21
TouchPad Basics The following items show you how to use the TouchPad: • Move your finger across the TouchPad (1) to move the cursor. • Press the left (2) and right (3) buttons located beneath the TouchPad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the TouchPad is the same as clicking the left button. Function Left Button (2) Right Button (3) Main TouchPad (1) Execute Quickly click twice.
PAGE 22
Using the Keyboard The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function and special keys. Lock Keys and embedded numeric keypad The keyboard has three lock keys which you can toggle on and off. Lock key Description Caps Lock When Caps Lock is on, all alphabetic characters typed are in uppercase. Num Lock + When Num Lock is on, the embedded keypad is in numeric mode.
PAGE 23
Windows Keys The keyboard has two keys that perform Windows-specific functions. Key Description Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu.
PAGE 24
Hot Keys The computer employs hotkeys or key combinations to access most of the computer’s controls like screen brightness, volume output and the BIOS utility. To activate hot keys, press and hold the key before pressing the other key in the hotkey combination. Hotkey 14 Icon Function Description + Acer eSettings Management Launches Acer eSettings Management in Acer Empowering Technology. + Bluetooth Enables/disables the Bluetooth function.
PAGE 25
Special Key You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your keyboard. The Euro symbol 1. Open a text editor or word processor. 2. Hold and then press the <5> key at the upper-center of the keyboard. NOTE: Note: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/ typography/faq/faq12.htm for more information. The US dollar sign 1. Open a text editor or word processor. 2.
PAGE 26
Using the System Utilities Acer GridVista (dual-display compatible) NOTE: This feature is only available on certain models. To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new settings and click OK to complete the process.
PAGE 27
Hardware Specifications and Configurations Processor Item Specification CPU Intel® Core™2 Duo mobile processor, supporting Intel® 64 architecture Intel® PDC/Celeron mobile processor Type Intel Mobile Memron uPGA Core Logic Intel Cantiga GM45/GL40 chipset with ICH9M CPU Package Micro uPGA-478 Package Power On-die Cache 4MB L2 cache Front Side Bus 667/800/1066MHz Processor Specifications CPU Speed Item Cores Bus Speed Mfg Tech Cache Size Package Core Voltage Acer P/N T1600 1.
PAGE 28
Item Specification Package BGA-676 Features • BIOS Item Specification BIOS vendor Insyde BIOS BIOS Version V0.06-T02 BIOS ROM type Flash Features • Flash ROM 1MB • Supports ISIPP • Supports Acer UI • Supports multi-boot • Suspend to RAM (S3)/Disk (S4) • Various hot-keys for system control • Supports SMBUS 2.0, PCI2.3 • ACPI 2.
PAGE 29
Memory Combinations Slot 1 Slot 2 Total Memory 0MB 512MB 512MB 0MB 1024MB 1024MB 0MB 2048MB 2048MB 512MB 512MB 1024MB 512MB 1024MB 1536MB 512MB 2048MB 2560MB 1024MB 0MB 1024MB 1024MB 512MB 1536MB 1024MB 1024MB 2048MB 1024MB 2048MB 3072MB 2048MB 0MB 2048MB 2048MB 512MB 2560MB 2048MB 1024MB 3072MB 2048MB 2048MB 4096MB NOTE: Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations.
PAGE 30
Item Spindle speed (RPM) Specification 5400 5400 5400 5400 8 MB 8 MB 8 MB Performance Specifications Buffer size 8 MB Interface SATA SATA SATA SATA Internal transfer rate (Mbits/sec, max) 352 395~952 (typical) 850 Mbits/s maximum I/O data transfer rate (Mbytes/sec max) 150 300 300 maximum 5V ±5% 5V ±5% 5V ±5% DC Power Requirements Voltage tolerance 20 5V ±5% Chapter 1
PAGE 31
Super-Multi Drive Module Item Specification Vendor & model name HLDS GT20N Performance Specification With CD Diskette With DVD Diskette With CD Diskette Sony AD7580S With DVD Diskette Transfer rate (MB/sec) Sustained: 3,600 KB/s (24x) max. Sustained: 11.08 Mbytes/s (8x) max. Sustained: 1,571 (typical) Sustained: 10,993 (typical) Buffer Memory 2 MB Interface SATA Applicable disc formats • DVD-ROM: • • • DVD-R: • 3.95GB (Ver. 1.0: read only) 4.7GB (Ver. 2.0 for Authoring: read only) 4.
PAGE 32
Power and Keyboard Controller Item Specification Controller ENE KB926 Package Features • Touchpad pointing device Supply Current Total number of keypads 99-/100-/103-key keyboard Windows logo key Yes Hotkeys See “Hot Keys” on page 14. Battery Specification Item 6 Cell Vendor & model name SANYO/SONY/PANASONIC/SIMPLO AS2009A Battery Type Li-ion Pack capacity 4400 mAh Normal Voltage 2.2 Ah Package configuration 3S2P LCD 15.
PAGE 33
Card Reader Item Specification Part Name RealTek RT5159 Package 5-in-1 card reader General Features Chapter 1 • PCI-E interface • Push-push type • Dummy card 23
PAGE 34
24 Chapter 1
PAGE 35
Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.
PAGE 36
HM50-MV Intel BIOS Information The Information screen displays a summary of your computer hardware information. Information Main InsydeH20 Setup Utility Security Power Boot Exit Advanced CPU Type CPU Speed Intel(R) Pentium(R) Dual-Core CPU 2.1GHz HDD Model Name: HDD Serial Number: HDD Model Name: HDD Serial Name: ATAPI Model Name: WDC WD1600BEVT-22ZCTO System BIOS Version: VGA BIOS Version: Serial Number: Asset Tag Number: Product Name: Manufacturer Name: UUID: V0.
PAGE 37
Main The Main screen allows the user to set the system time and date as well as enable and disable boot option and recovery. Information Main InsydeH20 Setup Utility Security Boot Power Exit Advanced Rev. 3.
PAGE 38
Advanced The Advanced screen allows the user to configure the various advanced BIOS options. IMPORTANT:Making incorrect settings to items on these pages may cause the system to malfunction. Unless you have experience adjusting these items, we recommend that you leave these settings at the default values. If making settings to items on these pages causes your system to malfunction or prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to boot up normally.
PAGE 39
Parameter Description Submenu Items Video Configuration Enter the Video Configuration menu. • • • • • • • • • • Render Standby IGD—Device2, Function1 IGD—Pre-allocat Memory IGD—DVMT Size Clock Chip Initialize Enabled CK SSC IGD—Boot Type IGD—LCD Panel Type IGD—TV IGD—PAVP Mode USB Configuration Enter the USB Configuration menu. • • • • • USB Legacy EHCI 1, 2 UHCI 1 ~ 5 Per-Port Control USB Port 0~7 Chipset Configuration Enter the Chipset Configuration menu.
PAGE 40
Security The Security screen contains parameters that help safeguard and protect your computer from unauthorized use. Information Main Advanced InsydeH20 Setup Utility Security Power Boot Exit Rev. 3.
PAGE 41
Setting a Password Follow these steps as you set the user or the supervisor password: 1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears: Set Supervisor Password Enter New Password Confirm New Password 2. [ [ ] ] Type a password in the “Enter New Password” field. The password length can not exceed 8 alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New Password” field.
PAGE 42
Changing a Password 1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears. Set Supervisor Password Enter Current Password Enter New Password Confirm New Password [ [ [ ] ] ] 2. Type the current password in the Enter Current Password field and press Enter. 3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field. 4. Press Enter.
PAGE 43
Power The Advanced screen allows the user to configure the various advanced BIOS options. IMPORTANT:Making incorrect settings to items on these pages may cause the system to malfunction. Unless you have experience adjusting these items, we recommend that you leave these settings at the default values. If making settings to items on these pages causes your system to malfunction or prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to boot up normally.
PAGE 44
Parameter 34 Description Submenu Items Break Event Enter the Break Event menu • • • • • • Storage Break Event PCIE Break Event PCI Break Event EHCI Break Event UHCI Break Event HDA Break Event ACPI S3 Enable or Disable ACPI S1/S3 Sleep State. N/A Wake on PME Disable or Enable wake up when the system power is off and a PCI Power Management Enable wake up event occurs.
PAGE 45
Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay. Select Boot Devices to select specific devices to support boot. Information Main Advanced InsydeH20 Setup Utility Security Power Boot Exit Rev. 3.5 Item Specific Help Boot priority order: 1. 2. 3. 3. 4. 5. 6.
PAGE 46
Exit The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility. Information Main Advanced InsydeH20 Setup Utility Security Power Boot Exit Rev. 3.5 Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Help ESC Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
PAGE 47
BIOS Flash Utilities The BIOS flash memory update is required for the following conditions: • New versions of system programs • New features or options • Restore a BIOS when it becomes corrupted. Use the Phlash utility to update the system BIOS flash ROM. NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Phlash utility. NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
PAGE 48
DOS Flash Utility Perform the following steps to use the DOS Flash Utility: 1. Press F2 during boot to enter the Setup Menu. 2. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move USB HDD to position 1. Information Main Advanced InsydeH20 Setup Utility Security Power Boot Exit Rev. 3.5 Item Specific Help Boot priority order: 1. 2. 3. 3. 4. 5. 6. F1 Help ESC Exit 3.
PAGE 49
4. In flash BIOS, the message Please do not remove AC Power Source displays. NOTE: If the AC power is not connected, the following message displays. Plug in the AC power to continue. 5. Flash is complete when the message Flash programming complete displays.
PAGE 50
WinFlash Utility Perform the following steps to use the WinFlash Utility: 40 1. Double-click the WinFlash executable. 2. Click OK to begin the update. A progress screen displays.
PAGE 51
Remove HDD/BIOS Password Utilities This section provides you with details about removing HDD/BIOS password: Remove HDD Password: If you key in the wrong HDD password three times, an error is generated. To reset the HDD password, perform the following steps: 1. After the error is displayed, select the Enter Unlock Password option on the screen. 2. An Encode key is generated for unlocking utilities. Note down this key. 3. Execute the UnlockHD.
PAGE 52
Removing BIOS Passwords: To clear the User or Supervisor passwords, open the RAM door and use a metal instrument to short the J1 jumper. Cleaning BIOS Passwords To clean the User or Supervisor passwords, perform the following steps: 1. From a DOS prompt, execute clnpwd.exe 2. Press 1 or 2 to clean the desired password shown on the screen. The onscreen message determines whether the function is successful or not.
PAGE 53
Using Boot Sequence Selector The Boot Sequence Selector allows the boot order to be changed without accessing the BIOS. To use Boot Sequence Selector, perform the following steps: 1. Enter into DOS. 2. Execute BS.exe to display the usage screen. 3. Select the desired boot sequence by entering the corresponding sequence. For example, enter BS2 to change the boot sequence to HDD | CD ROM | LAN | Floppy.
PAGE 54
Using DMITools The DMI (Desktop Management Interface) Tool copies BIOS information to EEPROM to be used in the DMI pool for hardware management. When the BIOS displays Verifying DMI pool data it is checking that the table correlates with the hardware before sending to the operating system (Windows, etc.). To update the DMI Pool, perform the following steps: 1. Boot into DOS. 2. Execute dmitools.
PAGE 55
Using the LAN MAC EEPROM Utility You can use the MAC.BAT utility to write the MAC.CFG file to the EEPROM under DOS mode. 1. 2. Use a text editor (for example: Notepad) to open the MAC.CFG file. You can see the MAC.CFG contents as below: WriteData = ‘001122334455' MAC value StartAddr=7A MAC address WriteLeng=6 MAC value length KeepByte=0 don’t care In DOS mode, run the MAC.BAT file to write MAC values to eeprom.
PAGE 56
46 Chapter 2
PAGE 57
Chapter 3 Machine Disassembly and Replacement IMPORTANT: The outside housing and color may vary from the mass produced model. This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting.
PAGE 58
Pre-disassembly Instructions Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system. 3. Place the system on a flat, stable surface. 4. Remove the battery pack. Disassembly Process IMPORTANT: The LCD Module cannot be disassembled outside of factory conditions.
PAGE 59
External Module Disassembly Process IMPORTANT: The outside housing and color may vary from the mass produced model. External Modules Disassembly Flowchart The flowchart below gives you a graphic representation of the external module disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the keyboard, you must first remove the switch board.
PAGE 60
Removing the Battery Pack 1. Turn computer over. Slide the battery lock in the direction shown. 2. Slide and hold the battery release latch to the release position (1), then lift out the battery pack from the main unit (2).
PAGE 61
Removing the SD Dummy Card 1. Push the SD dummy card all the way in to eject it. 2. Pull it out from the slot.
PAGE 62
Removing the Lower Covers 1. See “Removing the Battery Pack” on page 50. 2. Remove the three (3) screws securing the Memory and HDD Covers. HDD Cover Memory Cover Step Lower Covers Size M2.5*8 Quantity Screw Type 3 3. Remove the HDD cover by the top edge as shown. 4. Carefully open the Memory Cover.
PAGE 63
Removing the Optical Drive Module 1. See “Removing the Battery Pack” on page 50. 2. Remove one (1) screw securing the ODD module. Step ODD Module Size M2.5*8 Quantity Screw Type 1 3. Insert a suitable tool into the access slot in the battery bay as shown. Gently lever the ODD module out of the chassis. 4. Pull the optical drive module out from the chassis.
PAGE 64
5. Remove the two (2) screws securing the ODD bracket and remove the ODD bracket from the optical disk drive module. Step ODD Bracket Size M2*3 Quantity Screw Type 2 6. Pull the top edge of the bezel downward and clear of the device.
PAGE 65
Removing the DIMM Modules 1. See “Removing the Lower Covers” on page 52. 2. Push out the release latches on both sides of the DIMM socket to release the DIMM module. 3. Remove the DIMM module. 4. Repeat steps for the second DIMM module if present.
PAGE 66
Removing the WLAN Module 1. See “Removing the Lower Covers” on page 52. 2. Remove the adhesive tape securing the Antenna cables in place. 3. Disconnect the antenna cables from the WLAN Board. NOTE: Cable placement is Black to the MAIN terminal and White to the AUX terminal.
PAGE 67
4. Move the antenna away and remove the two (2) screws to release the WLAN Board. Step WLAN Module Size M2*3 Quantity Screw Type 2 5. Detach the WLAN Board from the WLAN socket. NOTE: When reattaching the antennas, ensure the cables are tucked into the chassis to prevent damage.
PAGE 68
Removing the Hard Disk Drive Module 1. See “Removing the Lower Covers” on page 52. 2. Using the pull, slide the HDD Module in the direction of the arrow to disconnect the interface. 3. Lift the HDD Module clear of the HDD bay. NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
PAGE 69
4. Remove the four (4) screws (two on each side) securing the hard disk to the carrier. Step HDD Carrier Size M3*3 Quantity Screw Type 4 5. Remove the HDD from the carrier.
PAGE 70
Main Unit Disassembly Process Main Unit Disassembly Flowchart Remove External Modules before proceeding Remove Switch Cover Remove Keyboard Remove LCD Module Remove Upper Cover Upper Cover Remove Power Board Remove Left Speaker Module Lower Cover Remove Right Speaker Module Remove TouchPad Bracket Remove Mainboard Remove RTC Battery Remove Thermal Module Remove CPU Fan Remove CPU Screw List Step 60 Screw Quantity Part No. LCD Module M2.5*8 2 86.N2802.003 LCD Module M2.5*8 4 86.
PAGE 71
Removing the Switch Cover CAUTION: Using metal tools to remove the Switch Cover may cause damage to the outer casing. The use of plastic tools or fingers is recommended to remove the Switch Cover. 1. See “Removing the Battery Pack” on page 50. 2. Turn the computer over. Press down the / and * keys on the right side of the Keyboard to expose the cutout. Insert a suitable plastic tool (or finger) and pry the Switch Cover upward, away from the Upper Cover. 3.
PAGE 72
Removing the Keyboard 1. See “Removing the Switch Cover” on page 61. 2. Pry up the centre of the Keyboard and rotate it upward away from the Upper Cover. 3. Turn the keyboard over on to the TouchPad area to expose the FFC connector. 4. Open the locking latch and disconnect the FFC from the mainboard. 5. Lift the keyboard clear of the Upper Cover.
PAGE 73
Removing the LCD Module 1. See “Removing the Keyboard” on page 62. 2. Turn the computer over. Remove the two (2) securing screws from the bottom of the chassis. Step LCD Module Size M2.5*8 Quantity Screw Type 2 3. Remove the Antenna Cables from the cable channel as shown. Ensure that the cables are free from all cable clips.
PAGE 74
4. Stand the computer on the LCD Panel and pull the Antenna cables completely through the chassis. 5. Disconnect the LCD cable from the Mainboard and remove the cable from the cable channel. 6. Remove the white Antenna cable from the cable channel. Ensure that the cable is completely free of the retaining clips all the way to the hinge well.
PAGE 75
7. Remove the adhesive tape securing the Antenna cable to the Upper Cover. 8. Remove the black Antenna cable from the cable channel as shown. Ensure that the cable is completely free of the retaining clips all the way to the hinge well. 9. Open the LCD Panel to the full extent to expose the Hinge Covers. 10. Press the left side Hinge Cover inward, as shown, and lift to remove the cover from the chassis. 11. Repeat the process for the right side Hinge Cover.
PAGE 76
12. Remove the four (4) securing screws (two each side) from the LCD module. Step LCD Module Size M2.5*8 Quantity Screw Type 4 13. Remove the left and right screw covers from on top of the hinges 14. Lift the LCD Module clear of the Upper Cover.
PAGE 77
Removing the Upper Cover 1. See “Removing the LCD Module” on page 63. 2. Turn the computer over. Remove the eleven (11) screws on the bottom panel. Step Upper Cover Size M2.5*8 Quantity Screw Type 11 3. Turn the computer over. Remove the three screw caps at the rear of the Upper Cover as shown.
PAGE 78
4. Disconnect the following four cables from the Mainboard, labeled A,B,C and D.
PAGE 79
5. Disconnect A as shown. 6. Disconnect C as shown. A C 7. Release the locking latch on B and remove the FFC cable as shown. B 8. Release the locking latch on D and remove the FFC cable as shown. D NOTE: Avoid pulling on cables directly to prevent damage to the connectors. NOTE: Use the pull-tabs on FFCs whenever available to prevent damage.
PAGE 80
9. Remove the nine (9) screws on the top panel. Step Upper Cover Size M2.5*8 Quantity Screw Type 9 10. Starting at the rear left side of the cover, pry apart the Upper and Lower Covers as shown. Work along the back edge of the casing to the right as shown, then lift the Upper Cover clear of the Lower Cover.
PAGE 81
Removing the Power Board 1. See “Removing the Upper Cover” on page 67. 2. Locate the Power Board on the Upper Cover as shown. 3. Remove the two (2) screws securing the Power Board to the Upper Cover. Step Power Board Size M2*3 Quantity Screw Type 2 4. Lift the Power Board clear of the Upper Cover as shown.
PAGE 82
Removing the Left Speaker Module 1. See “Removing the Upper Cover” on page 67. 2. Locate the Left Speaker Module on the Upper Cover as shown. 3. Remove the adhesive tape from the Speaker cable. 4. Remove the Speaker cable from the cable channel. Ensure that the cable is free from all cable clips.
PAGE 83
5. Remove the one (1) securing screw from the Left Speaker Module. Step Left Speaker Module Size M2*3 Quantity Screw Type 1 6. Lift the Speaker clear of the Upper Cover, left side first as shown.
PAGE 84
Removing the Right Speaker Module 1. See “Removing the Upper Cover” on page 67. 2. Locate the Right Speaker Module on the Upper Cover as shown. 3. Turn the Upper Cover over and remove the Right Speaker Module cable from the cable channel. Ensure that the cable is free from all cable clips. 4. Turn the Upper Cover over and pass the cable through the cover as shown.
PAGE 85
5. Remove the one (1) securing screw from the Right Speaker Module. Step Right Speaker Module Size M2*3 Quantity Screw Type 1 6. Lift the Speaker clear of the Upper Cover, right side first as shown.
PAGE 86
Removing the TouchPad Bracket IMPORTANT: The TouchPad Board cannot be removed individually. To replace the TouchPad Board, replace the entire Upper Cover. 1. See “Removing the Upper Cover” on page 67. 2. Lift the FFC to detach the adhesive securing the cable to the Upper Cover. 3. Release the FFC locking latch and disconnect the TouchPad FFC from the cover.
PAGE 87
4. Remove the two (2) screws from TouchPad bracket. Step TouchPad Bracket Size M2*3 Quantity Screw Type 2 5. Lift the rear edge of the TouchPad bracket first to clear the securing clips and remove it as shown.
PAGE 88
Removing the Mainboard 1. See “Removing the Upper Cover” on page 67. 2. Remove the one (1) securing screw from the Mainboard. Step Mainboard Size M2.5*4 Quantity Screw Type 1 3. Lift the mainboard from the chassis, internal edge first, and place it on a clean, dust-free surface.
PAGE 89
Removing the RTC Battery IMPORTANT:Follow local regulations for disposal of all batteries. The RTC Battery is soldered to the Mainboard. To replace the battery, solder the new battery to the connections shown.
PAGE 90
Removing the Thermal Module 1. See “Removing the Lower Covers” on page 52. 2. Remove the four securing screws (in reverse numerical order from screw 4 to screw 1) from the Thermal Module. Step Thermal Module Size 4 2 1 3 Quantity Screw Type 4 3. Using both hands, lift the Thermal Module clear of the Mainboard.
PAGE 91
Removing the CPU Fan 1. See “Removing the Thermal Module” on page 80. 2. Disconnect the Fan cable from the Mainboard as shown. 3. Remove the three (3) securing screws from the Fan Module.
PAGE 92
4. Lift the CPU Fan clear of the Mainboard as shown.
PAGE 93
Removing the CPU IMPORTANT: The pins on the underside of the CPU are very delicate. If they are damaged, the CPU may malfunction. Place the CPU on a clean, dry surface when it is not installed. 1. See “Removing the Thermal Module” on page 80. 2. Using a flat-bladed screw driver, rotate the CPU locking screw 180° counter-clockwise as shown. 3. Lift the CPU clear of the socket as shown.
PAGE 94
LCD Module Disassembly Process LCD Module Disassembly Flowchart Remove LCD Panel from Main Unit before proceeding Remove LCD Bezel Remove Camera Module Remove LCD Panel Remove LCD Brackets Remove LCD FPC Cable Remove Antennas Quantity Part No. Screw List Step 84 Screw LCD Bezel M2.5*6 4 86.N2802.002 LCD Panel M2.5*6 2 86.N2802.002 LCD Brackets M2*3 6 86.N2802.
PAGE 95
Removing the LCD Bezel 1. See “Removing the LCD Module” on page 63. 2. Remove the two (2) upper and two (2) lower bezel screw caps and screws. Step LCD Bezel 3. Size M2.5*6 Quantity Screw Type 4 Starting from the bottom edge of the bezel, pry the bezel upwards and away from the panel. Work along the right side toward the top of the bezel, prying the covers apart. Continue along the top edge and down the left side to remove the bezel.
PAGE 96
Removing the Camera Module 1. See “Removing the LCD Bezel” on page 85. 2. Locate the Camera Module at the top of the LCD Module and disconnect the camera cable. 3. Remove the Camera from the module.
PAGE 97
Removing the LCD Panel 1. See “Removing the Camera Module” on page 86. 2. Remove the two (2) securing screws from the LCD Panel. Step LCD Panel Size M2.5*6 Quantity Screw Type 2 3. Remove the adhesive strip holding the cables in place. 4. Remove the Camera cable cluster from the LCD Module as shown.
PAGE 98
5. Lift the LCD Panel clear of the module.
PAGE 99
Removing the LCD Brackets and FPC Cable 1. See “Removing the LCD Panel” on page 87. 2. Remove the six (6) securing screws (three on each side) from the LCD Panel brackets. Step LCD Brackets Size M2*3 Quantity Screw Type 6 3. Remove the LCD brackets by pulling away from the LCD Panel.
PAGE 100
4. Place the LCD panel face down on a soft clean surface.Turn the LCD panel over to expose the rear. Lift the adhesive protector and disconnect the cable from the LCD Panel. 5. Lift the cable as shown to pull free the adhesive strip securing it in place. 6. Lift the FPC cable to disengage the remaining adhesive and remove the cable from the panel.
PAGE 101
Removing the Antennas 1. See “Removing the LCD Panel” on page 87. 2. Remove the adhesive strips holding the left antenna cable in place. Ensure the cable is free from obstructions. 3. Remove the cable from the cable channel. Ensure that the cable is free from all cable clips and adhesive strips. 4. Remove the adhesive tape securing the left Antenna to the LCD Module.
PAGE 102
5. Lift the left Antenna clear of the cover. 6. Remove the adhesive strips holding the right antenna cable in place. Ensure the cable is free from obstructions. 7. Remove the cable from the cable channel. Ensure that the cable is free from all cable clips and adhesive strips.
PAGE 103
8. Remove the adhesive tape securing the right Antenna to the LCD Module. 9. Lift the right Antenna clear of the cover.
PAGE 104
LCD Module Reassembly Procedure Replacing the Antennas 1. Replace the right Antenna as shown. Ensure that the locating pins on the Antenna are correctly seated. Locating Pin Locating Pin 2. Replace the adhesive strip to secure the Antenna in place. 3. Lay the cable down the side of the LCD Module using all available clips and adhesive. 4. Run the cable along the cable channel as shown, using all available cable clips.
PAGE 105
5. Replace the left Antenna as shown. Ensure that the locating pins on the Antenna are correctly seated. Locating Pin 6. Replace the adhesive strip to secure the Antenna in place. Locating Pin 7. Run the cable down the side of the LCD Module using all available clips and adhesive. 8. Run the cable along the cable channel as shown, using all available cable clips and adhesive.
PAGE 106
9. The Antennas and cables appear as shown when correctly installed.
PAGE 107
Replacing the LCD Panel 1. Connect the LCD cable to the panel connector as shown. 2. Press down the adhesive strip to secure the cable in place. 3. Run the cable along the back of the panel and press down as indicated to secure the cable in place. 4. Run the cable across the back of the panel as shown and press down as indicated to secure the cable in place. IMPORTANT: Ensure that the LCD cable runs between the green callouts to avoid trapping when the panel is replaced in the LCD Module.
PAGE 108
5. Align the LCD brackets with the screw holes on the panel. Replace the six (6) screws (three on each side) in the brackets as shown. 6. Place the LCD Panel in the LCD Module, top edge first, and secure the LCD cable with adhesive tape. IMPORTANT: Ensure that the LCD power cable passes through the hinge well and is not trapped under the panel.
PAGE 109
7. Replace the Camera cable cluster in the LCD Module. 8. Secure the LCD module with the two securing screws. Replacing the Camera Module 1. Place the camera in the LCD Module. Chapter 3 2. Connect the cable to the camera module.
PAGE 110
Replacing the LCD Bezel 1. Replace the bezel and press down until there are no gaps between the bezel and the LCD Module. IMPORTANT: Ensure that the LCD cables pass through the hinge wells and are not trapped by the bezel.
PAGE 111
2. Replace the four (4) screws and screw caps provided.
PAGE 112
Main Module Reassembly Procedure Replacing the CPU IMPORTANT: The CPU has a Pin1 locator that must be positioned corresponding to the marker on the CPU socket. 1. Place the CPU into the CPU socket as shown, taking note of the Pin1 locator. Socket Pin1 Locator CPU Pin1 Locator 2. Using a flat-bladed screw driver, rotate the CPU locking screw 180° clockwise to secure the CPU in place.
PAGE 113
Replacing the CPU Fan 1. Align the screw holes on the CPU Fan and Mainboard and replace the Fan. 2. Replace the three (3) screws to secure the Fan to the Mainboard. 3. Connect the Fan power cable to the Mainboard connector. Replacing the Thermal Module IMPORTANT: Apply a suitable thermal grease and ensure all heat pads are in place before replacing the Thermal Module.
PAGE 114
3. Align the screw holes on the Thermal Module and Mainboard then replace the module. Keep the module as level as possible to spread the thermal grease evenly. 4. Replace the four (4) securing screws (in numerical order from screw 1 to screw 4) to secure the Thermal Module in place. 4 2 1 3 Replacing the Mainboard 1. Ensure that the Mainboard is face up (the CPU is not visible). Place the Mainboard in the chassis, I/O connectors first (1), then rotate it downward into position (2).
PAGE 115
Replacing the TouchPad Bracket 1. Replace the TouchPad bracket top edge first to engage the securing clips. 2. Press the bracket down to engage the securing clips. 3. Replace the two (2) screws to secure the TouchPad Bracket to the Upper Cover. 4. Replace the TouchPad FFC and close the locking latch on the connector.
PAGE 116
5. Replace the FFC and press down as indicated to adhere it to the Upper Cover.
PAGE 117
Replacing the Right Speaker Module 1. Place the module left side first on the Upper Cover 2. Replace the one (1) screw to secure the module in as shown. Ensure that the left side of the module is place. seated correctly in the securing clip. 3. Pass the cable through the Upper Cover as shown. 4. Turn the Upper Cover over and run the cable along the cable channel using all available cable clips. 5. The cable runs as shown when correctly installed.
PAGE 118
Replacing the Left Speaker Module 1. Place the module right side first on the Upper Cover as shown. Ensure that the right side of the module is seated correctly in the securing clip. 2. Replace the one (1) screw to secure the module in place. 3. Run the cable along the cable channel using all available cable clips. 4. Secure the cable in place with adhesive tape. 108 5. The cable runs as shown when correctly installed.
PAGE 119
Replacing the Power Board 1. Slide the Power Board in to the Upper Cover front edge first to engage the securing clip. 2. Press the board down to locate the securing pin. 3. Replace the two (2) screws to secure the board to the Upper Cover. Replacing the Upper Cover 1. Place the Upper Cover on the Lower Cover as shown.
PAGE 120
2. Press down around the edges to secure it in place. 3. Replace the nine (9) screws in the Upper Cover as shown.
PAGE 121
4. Replace the three (3) screw caps as shown. 5. Connect the following cables to the Mainboard.
PAGE 122
6. Connect A as shown. 7. Connect C as shown. A C 8. Connect B and close the locking latch to secure the cable in place. B 9. Connect D and close the locking latch to secure the cable in place.
PAGE 123
10. Turn the computer over and replace the eleven screws as shown. Replacing the LCD Module 1. Align the screw holes on the LCD Module and Upper Cover and replace the LCD Module. 2. The left and right screw covers are shaped differently. Ensure that the correct cover is used. Left Screw Cover Right Screw Cover 3. Replace the left screw cover as shown. Ensure that the securing tab on the rear of the cover is seated correctly in the Upper Cover.
PAGE 124
4. Replace the right screw cover as shown. Ensure that the securing tab on the rear of the cover is seated correctly in the Upper Cover. 5. Replace the four (4) screws securing the LCD Module to the Upper Cover. 6. Ensure that the Hinge Covers are replaced 7. Align the left Hinge Cover as shown and press correctly. Identify the rear edge of the covers by the down to replace the cover. two securing clips. Rear Securing Clips 8. Repeat the process for the right side Hinge Cover.
PAGE 125
9. Run the black Antenna cable along the cable channel as shown using all available retaining clips. 10. Replace the adhesive strip to secure the cable in place. 11. Run the white Antenna cable along the cable channel as shown using all available retaining clips. 12. Run the LCD cable along the cable channel using all available cable clips. Chapter 3 13. Connect the LCD cable to the Mainboard as shown.
PAGE 126
14. Stand the computer on the LCD Panel and pass the Antenna cables through the chassis. 15. The Upper Cover appears as shown when the Antenna and LCD cables are correctly installed. 16. Turn the computer over. Run the Antenna cables along the cable channel as shown, using all available cable clips.
PAGE 127
17. Replace the two (2) screws securing the LCD Module to the Lower Cover.
PAGE 128
Replacing the Keyboard 1. Connect the Keyboard FFC to the Mainboard and close the locking latch to secure the cable in place. 2. Turn the Keyboard over and insert it front edge first 3. Press down as indicated to secure the Keyboard in into the chassis. place. NOTE: Ensure that the six locating tabs are correctly seated.
PAGE 129
Replacing the Switch Cover 1. Place the Switch Cover left side first on to the Upper Cover. 2. Press down as indicated to snap the Switch Cover into place. Replacing the Hard Disk Drive Module 1. Place the HDD in the HDD carrier. Chapter 3 2. Replace the four (4) screws (two each side) to secure the carrier.
PAGE 130
3. Insert the HDD, as indicated and lower it into place. 120 4. Slide the HDD in the direction of the arrow to connect the interface.
PAGE 131
Replacing the WLAN Module 1. Insert the WLAN Module into the WLAN socket. 2. Replace the two (2) screws to secure the module. 3. Connect the two (2) Antenna cables to the module. 4. After connecting the cables to the terminals, secure the cables in place with adhesive tape to NOTE: The black cable connects to the upper avoid trapping. terminal (MAIN) and the white cable to the lower terminal (MAIN). Replacing the DIMM Modules 1. Insert the DIMM Module in place. 2.
PAGE 132
Replacing the ODD Module 1. Press the bezel into the tray, bottom edge first, to secure it to the ODD Module. 2. Secure the ODD bracket with the two (2) screws. 3. Push the ODD Module into the ODD bay until it is flush with the casing. 4. Replace the one (1) screw to secure the Module. Replacing the Lower Covers 1. Replace the Memory Cover as shown. 2. Replace the HDD Cover as shown.
PAGE 133
3. Replace the three (3) screws to secure the covers in place. Memory Cover HDD Cover Replacing the SD Dummy Card 1. Insert the SD Dummy Card into the slot as shown. Chapter 3 2. Push until the card clicks into place and is flush with the casing.
PAGE 134
Replacing the Battery 1. Slide and hold the battery release latch to the release position (1), insert the battery pack and press down (2). 2. Slide the battery lock in the direction shown to secure the battery in place.
PAGE 135
Chapter 4 Troubleshooting Common Problems Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3.
PAGE 136
Power On Issue If the system doesn’t power on, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Computer Shuts down Intermittently If the system powers off at intervals, perform the following actions one at a time to correct the problem. 126 1. Check the power cable is properly connected to the computer and the electrical outlet. 2. Remove any extension cables between the computer and the outlet. 3.
PAGE 137
No Display Issue If the Display doesn’t work, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: No POST or Video If the POST or video doesn’t display, perform the following actions one at a time to correct the problem. 1. Make sure that the internal display is selected. On this notebook model, switching between the internal display and the external display is done by pressing Fn+F5. Reference Product pages for specific model procedures. 2.
PAGE 138
Abnormal Video Display If video displays abnormally, perform the following actions one at a time to correct the problem. 1. Reboot the computer. 2. If permanent vertical/horizontal lines or dark spots display in the same location, the LCD is faulty and should be replaced. See “Disassembly Process” on page 48. 3. If extensive pixel damage is present (different colored spots in the same locations on the screen), the LCD is faulty and should be replaced. See “Disassembly Process” on page 48. 4.
PAGE 139
LCD Failure If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs: Built-In Keyboard Failure If the built-in Keyboard fails, perform the following actions one at a time to correct the problem.
PAGE 140
TouchPad Failure If the TouchPad doesn’t work, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Internal Speaker Failure If the internal Speakers fail, perform the following actions one at a time to correct the problem.
PAGE 141
Sound Problems If sound problems are experienced, perform the following actions one at a time to correct the problem. 1. Reboot the computer. 2. Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager. Check the Device Manager to determine that: • The device is properly installed. • There are no red Xs or yellow exclamation marks. • There are no device conflicts. • No hardware is listed under Other Devices. 3.
PAGE 142
HDD Not Operating Correctly If the HDD does not operate correctly, perform the following actions one at a time to correct the problem. 1. Disconnect all external devices. 2. Run a complete virus scan using up-to-date software to ensure the computer is virus free. 3. Run the Windows OS Startup Repair Utility: a. Insert the Windows Operating System DVD in the ODD and restart the computer. b. When prompted, press any key to start to the operating system DVD. c. The Install Windows screen displays.
PAGE 143
ODD Failure If the ODD fails, perform the following actions one at a time to correct the problem.
PAGE 144
a. Double-click lDE ATA/ATAPI controllers. If a device displays a down arrow, right-click on the device and click Enable. b. Double-click DVD/CD-ROM drives. If the device displays a down arrow, right-click on the device and click Enable. c. Check that there are no yellow exclamation marks against the items in lDE ATA/ATAPI controllers. If a device has an exclamation mark, right-click on the device and uninstall and reinstall the driver. d.
PAGE 145
b. Double-click IDE ATA/ATAPI controllers, then right-click ATA Device 0. c. Click Properties and select the Advanced Settings tab. Ensure that the Enable DMA box is checked and click OK. d. Repeat for the other ATA Devices shown if applicable. Drive Not Detected If Windows cannot detect the drive, perform the following actions one at a time to correct the problem. 1. Restart the computer and press F2 to enter the BIOS Utility. 2.
PAGE 146
Wireless Function Failure If the WLAN fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs: Thermal Unit Failure If the Thermal Unit fails, perform the following actions one at a time to correct the problem.
PAGE 147
External Mouse Failure If an external Mouse fails, perform the following actions one at a time to correct the problem. 1. Try an alternative mouse. 2. If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See the mouse user manual. 3. If the mouse uses a USB connection, try an alternate USB port. 4. Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure. 5. Restart the computer. 6.
PAGE 148
Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3.
PAGE 149
Post Codes These tables describe the POST codes and descriptions during the POST. Sec: NO_EVICTION_MODE_DEBUG EQU 1 (CommonPlatform\sec\Ia32\SecCore.inc) Code Description 0xC2 MTRR setup 0xC3 Enable cache 0xC4 Establish cache tags 0xC5 Enter NEM, Place the BSP in No Fill mode, set CR0.CD = 1, CR0.NW = 0. 0xCF Cache Init Finished Memory: DEBUG_BIOS equ 1 (Chipset\Alviso\MemoryInitAsm\IA32\IMEMORY.
PAGE 150
Code Description 0x27 Enable DRAM Channel I/O Buffers 0x28 Enable all clocks on populated rows 0x29 Perform JEDEC memory initialization for all memory rows 0x30 Perform steps required after memory init 0x31 Program DRAM throttling and throttling event registers 0x32 Setup DRAM control register for normal operation and enable 0x33 Enable RCOMP 0x34 Clear DRAM initialization bit in the SB 0x35 Initialization Sequence Completed, program graphic clocks 0xAF Disable access to the XMM registe
PAGE 151
Code Description 0xF8 Report that ExitBootServices () has been called 0xF9 Runtime driver set virtual address map Chapter 4 141
PAGE 152
Each PEIM entry point used in 80_PORT Code Description 0x00 0x01 PEI_EVENT_LOG 0x02 PEI_OEM_SERVICE 0x03 PEI_SIO_INIT 0x04 PEI_MONO_STATUS_CODE 0x05 PEI_CPU_IO_PCI_CFG 0x06 PEI_CPU_IO 0x07 PEI_PCI_CFG 0x08 PEI_CPU_PEIM 0x09 PEI_PLATFORM_STAGE1 0x0A PEI_VARIABLE 0x0B PEI_SB_INIT 0x0C PEI_CAPSULE 0x0D PEI_PLATFORM_STAGE2 0x0E PEI_SB_SMBUS_ARP_DISABLED 0x0F PEI_HOST_TO_SYSTEM 0x10 PEI_MEMORY_INIT 0x11 PEI_S3_RESUME 0x12 PEI_CLOCK_GEN 0x13 PEI_OP_PRESENCE 0x14 PEI_TPM_TC
PAGE 153
Code Description 0x3B MONOTONIC_COUNTER 0x3C WATCH_DOG_TIMER 0x3D SECURITY_STUB 0x3E DXE_CPU_IO 0x3F CF9_RESET 0x40 PC_RTC 0x41 STATUS_CODE 0x42 VARIABLE 0x43 EMU_VARIABLE 0x44 DXE_CHIPSET_INIT 0x45 DXE_ALERT_FORMAT 0x46 PCI_HOST_BRIDGE 0x47 PCI_EXPRESS 0x48 DXE_SB_INIT 0x49 IDE_CONTROLLER 0x4A SATA_CONTROLLER 0x4B SB_SM_BUS 0x4C ISA_ACPI_DRIVER 0x4D ISA_BUS 0x4E ISA_SERIAL 0x4F IDE_BUS 0x50 PCI_BUS 0x51 BOOT_PRIORITY 0x52 FVB_SERVICE 0x53 ACPI_PLATFORM 0x
PAGE 154
Code 144 Description 0x66 BIOS_KEYBOARD 0x67 BIOS_VEDIO 0x68 MONITER_KEY 0x69 LEGACY_BIOS 0x6A LEGACY_BIOS_PLATFORM 0x6B PCI_PLATFORM 0x6C ISA_FLOOPY 0x6D PS2_MOUSE 0x6E USB_BOT 0x6F USB_CBI0 0x70 USB_CBI1 0x71 USB_KB 0x72 USB_MASS_STORAGE 0x73 BUS_PCI_UHCI 0x74 USB_MOUSE 0x75 USB_BUS 0x76 SETUP_UTILITY 0x77 FW_BLOCK_SERVICE 0x78 USB_LEGACY_PLATFORM 0x79 GRAPHICS_CONSOLE 0x7A TERMINAL 0x7B DATA_HUB_STD_ERR 0x7C FAT 0x7D PARTITION 0x7E ENGLISH 0x7F FRENCH
PAGE 155
Code Description 0x91 DXE_0x91 PXE_BC 0x92 PXE_DHCP4 0x93 EBC 0x94~0x9F RESERVED 0xA0 DXE_H2O_DEBUG_IO 0xA1 DXE_H2O_DEBUG_IO 0xA2 DXE_TPM_TCG 0xA3 DXE_TPM_PHYSICAL_PRESENCE 0xA4 DXE_OEM_SERVICE 0xA5 DXE_EVENT_LOG 0xA6 DXE_ SECURITY_HDD_PASSWORD_SERVICE 0xA7 DXE_LAN_ASF_INIT 0xA8 DXE_BUS_PCI_SERIAL 0xA9 DXE_LAN_IDER_CONTROLLER 0xAA DXE_LAN_AMT 0xAB DXE_ SECURITY_SYSTEM_PASSWORD_SERVICE 0xAC DXE_ SECURITY_ PASSWORD_CONSOLE 0xAD DXE_ DATA_HUB_RECORD_POLICY 0xAE DXE_TPM_DR
PAGE 156
Each SmmDriver entry point used in 80_PORT Code Description 0xC0 SMM_ACCESS 0xC2 SMM_CONTROL 0xC1 SMM_BASE 0xC3 SMMAP 0xC4 SMMCORE 0xC5 SMM_DISPATCH 0xC6 SMM_START 0xC7 SMM_RUNTIME 0xC8 SB_SMM_DISPATCH 0xC9 SMM_THUNK 0xCA SMM_ACPI_SW_CHILD 0xCB SMM_SB_S3_SAVE 0xCC SMM_PLATFORM 0xCD SMM_GMCH_MBI 0xCE SMM_FW_BLOCK_SERVICE 0xCF SMM_VARIABLE 0xD0 SMM_IHISI 0xD1 SMM_INT15_MICROCODE 0xD2 SMM_PNP 0xD3 SMM_USB_LEGACY 0xD4 SMM_INT13_HDD 0xD5 SMM_INIT_PPM 0xD6 SMM_OHCI13
PAGE 157
Chapter 5 Jumper and Connector Locations Top View Item JLVDS1 JP14 Chapter 5 Description LCD Connector Power/B Connector JSPK1 Speaker (Left) Connector JSPK2 Speaker (Right) Connector JKB1 Internal Keyboard Connector JTP1 Touch Pad Connector U11 South Bridge SW4 Touch pad (Left) Button SW3 Touch pad (Right) Button 147
PAGE 158
Bottom View ITEM PJP1 AC-IN Connector JRJ45 RJ45 Connector JCRT1 CRT Connector JP12 Fan Connector JUSB1 USB Connector JUSB2 USB Connector JMIC1 MIC-In Jack JHP1 Head-Phone Jack JSATA2 U23 JCPU1 JREAD1 PJP2 148 DESCRIPTION HDD Connector North Bridge CPU Socket Card Reader Socket Battery Connector JDIMM2 Memory DIMM2 Connector JDIMM1 Memory DIMM1 Connector JSATA1 ODD Connector JMINI2 Wireless Card Connector Chapter 5
PAGE 159
Power Board ITEM U1 Chapter 5 DESCRIPTION Lid Switch SW1 TP Lock Button SW2 ON/OFF Button SW3 Wireless Button LED1 ON/OFF LED LED3 Media LED LED4 Num LED LED5 Wireless LED LED6 Caps LED LED7 TP Lock LED 149
PAGE 160
Clearing Password Check and BIOS Recovery This section provides you with the standard operating procedures of clearing password and BIOS recovery for eMachine HM50-MV. The machine provides one Hardware Open Gap on main board for clearing password check, and one Hotkey for enabling BIOS Recovery.
PAGE 161
BIOS Recovery by Crisis Disk BIOS Recovery Boot Block: BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous BIOS flashing process failed. BIOS Recovery Hotkey: The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered on during BIOS POST.
PAGE 162
152 Chapter 5
PAGE 163
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire 5732Z/5332. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
PAGE 164
Aspire 5732Z/5332 Exploded Diagrams Main Assembly 1 2 3 6 4 2 5 7 No. 154 Description Acer P/N No. Description Acer P/N 1 Middle Cover 60.PGT02.002 5 Mainboard MB.PGV02.001 2 Hinge Cover 42.N2802.001 6 Right Upper Cap 42.PGT02.001 3 Left Upper Cap 42.PGT02.002 7 Lower Cover 60.N2802.002 4 Upper Cover 60.PGT02.
PAGE 165
Mainboard Assembly 1 2 3 No. Chapter 6 Description Acer P/N 1 Fan 60.N2802.001 2 Heatsink 60.N2802.006 3 Mainboard MB.PGV02.
PAGE 166
Base Assembly 1 2 3 No. 1 156 Description RAM Door Acer P/N 42.N2802.004 2 HDD Door 42.N2802.005 3 Lower Cover 60.N2802.
PAGE 167
Aspire 5732Z/5332 FRU List CATEGORY Description AcerPN Board POWER BOARD 55.N2802.001 WLAN CARD-XB63 NI.23600.007 WLAN CARD-BCM4312 NI.23600.029 TP FFC 50.N2802.001 POWER CORD US 3 PIN 27.TAVV5.001 POWER CORD EU 3 PIN 27.TAVV5.002 Cable POWER CORD AUS 3 PIN 27.TAVV5.003 POWER CORD UK 3 PIN 27.TAVV5.004 POWER CORD CHINA 3 PIN 27.TAVV5.005 POWER CORD SWISS 3 PIN 27.TAVV5.006 POWER CORD ITALIAN 3 PIN 27.TAVV5.007 POWER CORD DENMARK 3 PIN 27.TAVV5.008 POWER CORD JP 3 PIN 27.TAVV5.
PAGE 168
CATEGORY Description AcerPN Case/Cover/Bracket Assembly 158 UPPER CASE ASSY 60.PGT02.001 LOWER CASE 60.N2802.002 TP BRACKET 33.N2802.001 MIDDLE COVER ASSY 60.PGT02.002 HINGE CAP ASSY 42.N2802.001 UP CAP R 42.PGT02.001 UP CAP L 42.PGT02.002 RAM DOOR ASSY 42.N2802.004 HDD DOOR ASSY 42.N2802.
PAGE 169
CATEGORY Description AcerPN HDD HDD SEAGATE 2.5" 5400rpm 160GB ST9160310AS Crockett SATA LF F/W:0303 KH.16001.034 HDD TOSHIBA 2.5" 5400rpm 160GB MK1655GSX Libra SATA LF F/W: FG011J KH.16004.006 HDD HGST 2.5" 5400rpm 160GB HTS543216L9A300 Falcon-B SATA LF F/W:C40C KH.16007.019 HDD HGST 2.5" 5400rpm 160GB HTS545016B9A300 Panther B SATA LF F/W:C60F KH.16007.024 HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO ML160 SATA LF F/W:11.01A11 KH.16008.022 HDD SEAGATE 2.
PAGE 170
CATEGORY Description AcerPN ODD BEZEL-SUPER MULTI 42.N2802.006 ODD BRACKET 33.N2802.003 Keyboard ACER EM-7Tv2 HM51 Internal 17 Standard 99KS Black US International Texture KB.I170A.140 Keyboard ACER EM-7Tv2 HM51 Internal 17 Standard 99KS Black Greek Texture KB.I170A.125 Keyboard ACER EM-7Tv2 HM51 Internal 17 Standard 99KS Black Arabic Texture KB.I170A.116 Keyboard ACER EM-7Tv2 HM51 Internal 17 Standard 99KS Black Chinese Texture KB.I170A.
PAGE 171
CATEGORY Description AcerPN Keyboard ACER EM-7Tv2 HM51 Internal 17 Standard 100KS Black Nordic Texture KB.I170A.129 Keyboard ACER EM-7Tv2 HM51 Internal 17 Standard 100KS Black FR/Arabic Texture KB.I170A.122 Keyboard ACER EM-7Tv2 HM51 Internal 17 Standard 100KS Black US w/ Canadian French Texture KB.I170A.142 Keyboard ACER EM-7Tv2 HM51 Internal 17 Standard 100KS Black Brazilian Portuguese Texture KB.I170A.118 Keyboard ACER EM-7Tv2 HM51 Internal 17 Standard 100KS Black CZ/SK Texture KB.I170A.
PAGE 172
CATEGORY Description AcerPN LCD BEZEL FOR W/CCD-AS 60.PEF02.001 LCD CABLE FOR W/CCD F 50.N2802.005 LCD BRACKET R&L FOR LCD 33.N2802.004 CAMERA 0.3 57.N2802.001 INVERTER 19.N2802.001 LCD BEZEL FOR W/O CCD-AS 60.N3202.001 LCD CABLE FOR W/O CCD F 60.PEE02.003 Mainboard AS5332 GL40 ICH9M 8132 W/O 1394 V1.0 LF MB.PGV02.
PAGE 173
CATEGORY Description AcerPN Memory NANYA SO-DIMM DDRII 667 1GB NT1GT64UH8D0FN-3C LF 64*16 0.07um KN.1GB03.026 Memory MICRON SO-DIMM DDRII 667 1GB MT8HTF12864HDY-667G1 LF 64*16 0.065um KN.1GB04.010 Memory SAMSUNG SO-DIMM DDRII 667 1GB M470T2864EH3-CE6 LF 64*16 0.055um KN.1GB0B.027 Memory HYNIX SO-DIMM DDRII 667 1GB HYMP112S64CP6-Y5 LF KN.1GB0G.012 Memory HYNIX SO-DIMM DDRII 667 1GB HMP112S6EFR6C-Y5 LF 64*16 0.055um KN.1GB0G.022 Memory NANYA SO-DIMM DDRII 667 2GB NT2GT64U8HD0BN-3C LF 128*8 0.
PAGE 174
Screw List Category 164 Description Acer P/N. SCREW SCREW M2.48D 4.0L K 5.5D 0.8T ZKNL 86.N2802.001 SCREW SCREW M2.48D 6.0L K 5.5D 0.8T ZKNL 86.N2802.002 SCREW SCREW M2.45D 8.0L K 5.5D 0.8T ZKNL 86.N2802.003 SCREW SCREW M1.98D 3.0L K 4.6D 0.8T ZKNL 86.N2802.004 SCREW SCREW M M 3.0D 3.0L K 4.9D NI + 86.N2802.005 SCREW SCREW M M 2.5D 3.2L K 6D NI + 86.N2802.
PAGE 175
Chapter 6 165
PAGE 176
Appendix A Model Definition and Configuration Model RO AS5332903G16Mn EMEA Denmark LX.PGV02.009 AS5332-903G16Mn W7HP64ATDK2 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_ENS1 CM900 AS5332903G16Mn EMEA Holland LX.PGV02.017 AS5332-903G16Mn W7HP64ATNL1 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_NL11 CM900 AS5332303G32Mn EMEA Denmark LX.PGV02.047 AS5332-303G32Mn W7HP64ATDK2 MC UMACbs2 2G+1G/320/6L2.2/5R/ CB_bgn_0.3D_HG_ENS1 CMT3000 AS5332302G25Mn PA ACLASpanish LX.PGV0C.
PAGE 177
Model RO Country Acer Part No Description CPU AS5332302G25Mn PA ACLASpanish LX.PGV08.003 AS5332-302G25Mn EM W7ST32EMATEA3 MC UMACbs2 2*1G/250/6L2.2/5R/ CB_bgn_0.3D_HG_ES51 CMT3000 AS5332302G25Mn PA ACLAPortuguese LX.PGV08.001 AS5332-302G25Mn EM W7ST32EMATXC2 MC UMACbs2 2*1G/250/6L2.2/5R/ CB_bgn_0.3D_HG_XC21 CMT3000 AS5332302G25Mn PA ACLAPortuguese LX.PGV08.002 AS5332-302G25Mn EM W7ST32EMATXC3 MC UMACbs2 2*1G/250/6L2.2/5R/ CB_bgn_0.
PAGE 178
Model RO AS5332903G16Mn EMEA Portugal LX.PGV02.008 AS5332-903G16Mn W7HP64ATPT1 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_PT11 CM900 AS5332903G16Mn EMEA Norway LX.PGV02.006 AS5332-903G16Mn W7HP64ATNO3 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_ENS1 CM900 AS5332903G16Mn EMEA UK LX.PGV02.004 AS5332-903G16Mn W7HP64ATGB1 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_EN11 CM900 AS5332903G16Mn EMEA Austria LX.PGV02.003 AS5332-903G16Mn W7HP64ATAT1 MC UMACbs2 2G+1G/160/6L2.
PAGE 179
Model RO AS5332903G16Mn EMEA Algeria LX.PGV02.035 AS5332-903G16Mn EM W7HP64EMATDZ1 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_ES81 CM900 AS5332903G16Mn EMEA South Africa LX.PGV02.036 AS5332-903G16Mn EM W7HP64EMATZA1 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_ES81 CM900 AS5332903G16Mn EMEA Middle East LX.PGV02.037 AS5332-903G16Mn EM W7HP64EMATME4 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_RU61 CM900 AS5332903G16Mn EMEA Middle East LX.PGV02.
PAGE 180
Model RO Country Acer Part No AS5332903G16Mn EMEA Middle East LX.PGV02.031 AS5332-903G16Mn EM W7HP64EMATME6 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_ES61 CM900 AS5332903G16Mn EMEA Middle East LX.PGV02.028 AS5332-903G16Mn EM W7HP64EMATME9 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_ES81 CM900 AS5332903G16Mn EMEA Czech LX.PGV02.027 AS5332-903G16Mn W7HP64ATCZ2 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_SK11 CM900 AS5332903G32Mn EMEA Eastern Europe LX.PGV0C.
PAGE 181
Model RO AS5332303G16Mn EMEA UK LX.PGW02.002 AS5332-303G16Mn W7HP64ATGB1 MC UMAbs2 2G+1G/160/6L2.2/5R/ CB_bgn_HG_EN11 CMT3000 AS5332303G50Mn EMEA UK LX.PGW02.004 AS5332-303G50Mn W7HP64ATGB1 MC UMAbs2 2G+1G/500_L/6L2.2/5R/ CB_bgn_HG_EN11 CMT3000 AS5332903G25Mn EMEA UK LX.PGW02.003 AS5332-903G25Mn W7HP64ATGB1 MC UMAbs2 2G+1G/250/6L2.2/5R/ CB_bgn_HG_EN11 CM900 AS5332303G16Mn EMEA UK LX.PGW0X.00 2 AS5332-303G16Mn VHP32ATGB1 MC UMAbs2 2G+1G/160/6L2.
PAGE 182
Model RO AS5732Z434G25Mn EMEA Poland LX.PGU02.038 AS5732Z-434G25Mn W7HP64ATPL1 MC UMACbs2 2*2G/250/6L2.2/5R/ CB_bgn_0.3D_HG_PL11 PMDT4300 AS5732Z434G25Mn EMEA Denmark LX.PGU02.036 AS5732Z-434G25Mn W7HP64ATDK1 MC UMACbs2 2*2G/250/6L2.2/5R/ CB_bgn_0.3D_HG_NO11 PMDT4300 AS5732Z434G32Mn PA USA LX.PGU02.110 AS5732Z-434G32Mn W7HP64ATUS1 MC UMACbs2 2*2G/320/6L2.2/5R/ CB_bgn_0.3D_HG_FRB5 PMDT4300 AS5732Z434G32Mn PA USA LX.PGU02.109 AS5732Z-434G32Mn W7HP64ATUS1 MC UMACbs2 2*2G/320/6L2.
PAGE 183
Model RO AS5732Z433G16Mn EMEA Cyprus LX.PGU02.103 AS5732Z-433G16Mn W7HP64ATCY1 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_ES61 PMDT4300 AS5732Z433G16Mn EMEA Italy LX.PGU02.102 AS5732Z-433G16Mn W7HP64ATIT1 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_IT11 PMDT4300 AS5732Z433G16Mn EMEA Greece LX.PGU02.101 AS5732Z-433G16Mn W7HP64ATGR1 MC UMACbs2 2G+1G/160/6L2.2/5R/ CB_bgn_0.3D_HG_EL31 PMDT4300 AS5732Z434G50Mn EMEA Israel LX.PGU02.
PAGE 184
Model RO Country Acer Part No Description CPU AS5732Z432G25Mn PA ACLASpanish LX.PGU08.001 AS5732Z-432G25Mn EM W7ST32EMATEA3 MC UMACbs2 2*1G/250/6L2.2/5R/ CB_bgn_0.3D_HG_ES51 PMDT4300 AS5732Z433G25Mn EMEA Middle East LX.PGU01.005 AS5732Z-433G25Mn EM W7HB64EMATME9 MC UMACbs2 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_HG_ES81 PMDT4300 AS5732Z432G25Mn EMEA Middle East LX.PGU0C.017 AS5732Z-432G25Mn LINPUSAME3 UMACbs2 1*2G/250/6L2.2/5R/CB_bgn_0.
PAGE 185
Model RO Country Acer Part No Description CPU AS5732Z434G50Mn PA ACLAPortuguese LX.PGU02.074 AS5732Z-434G50Mn EM W7HP64EMATXC2 MC UMACbs2 2*2G/500_L/6L2.2/5R/ CB_bgn_0.3D_HG_XC21 PMDT4300 AS5732Z434G32Mn PA ACLAPortuguese LX.PGU02.053 AS5732Z-434G32Mn EM W7HP64EMATXC2 MC UMACbs2 2*2G/320/6L2.2/5R/ CB_bgn_0.3D_HG_XC21 PMDT4300 AS5732Z433G25Mn PA ACLAPortuguese LX.PGU02.059 AS5732Z-433G25Mn EM W7HP64EMATXC2 MC UMACbs2 2G+1G/250/6L2.2/5R/ CB_bgn_0.
PAGE 186
Model RO Country Acer Part No Description CPU AS5732Z434G50Mn PA ACLASpanish LX.PGU02.076 AS5732Z-434G50Mn EM W7HP64EMATEA1 MC UMACbs2 2*2G/500_L/6L2.2/5R/ CB_bgn_0.3D_HG_ES51 PMDT4300 AS5732Z434G50Mn PA ACLASpanish LX.PGU02.075 AS5732Z-434G50Mn EM W7HP64EMATEA3 MC UMACbs2 2*2G/500_L/6L2.2/5R/ CB_bgn_0.3D_HG_ES51 PMDT4300 AS5732Z433G32Mn PA Chile LX.PGU02.072 AS5732Z-433G32Mn EM W7HP64EMATCL3 MC UMACbs2 2G+1G/320/6L2.2/5R/ CB_bgn_0.
PAGE 187
Model RO Country Acer Part No Description CPU AS5732Z434G32Mn PA ACLAPortuguese LX.PGU02.054 AS5732Z-434G32Mn EM W7HP64EMATXC3 MC UMACbs2 2*2G/320/6L2.2/5R/ CB_bgn_0.3D_HG_EN61 PMDT4300 AS5732Z433G25Mn PA ACLASpanish LX.PGU02.051 AS5732Z-433G25Mn EM W7HP64EMATEA4 MC UMACbs2 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_HG_EN31 PMDT4300 AS5732Z433G25Mn PA Chile LX.PGU02.052 AS5732Z-433G25Mn EM W7HP64EMATCL3 MC UMACbs2 2G+1G/250/6L2.2/5R/ CB_bgn_0.
PAGE 188
Model RO AS5732Z434G25Mi EMEA Russia LX.PGU02.017 AS5732Z-434G25Mi W7HP64RUATRU1 MC UMACbs2 2*2G/250/6L2.2/5R/ CB_bg_0.3D_HG_RU11 PMDT4300 AS5732Z434G25Mn EMEA Sweden LX.PGU02.021 AS5732Z-434G25Mn W7HP64ATSE1 MC UMACbs2 2*2G/250/6L2.2/5R/ CB_bgn_0.3D_HG_FI11 PMDT4300 AS5732Z434G25Mn EMEA Czech LX.PGU02.020 AS5732Z-434G25Mn W7HP64ATCZ2 MC UMACbs2 2*2G/250/6L2.2/5R/ CB_bgn_0.3D_HG_SK11 PMDT4300 AS5732Z434G25Mn EMEA Eastern Europe LX.PGU02.
PAGE 189
Model RO AS5732Z434G25Mn EMEA Greece LX.PGU02.040 AS5732Z-434G25Mn W7HP64ATGR1 MC UMACbs2 2*2G/250/6L2.2/5R/ CB_bgn_0.3D_HG_EL31 PMDT4300 AS5732Z434G25Mn EMEA Belgium LX.PGU02.039 AS5732Z-434G25Mn W7HP64ATBE1 MC UMACbs2 2*2G/250/6L2.2/5R/ CB_bgn_0.3D_HG_NL11 PMDT4300 AS5732Z434G25Mn EMEA Switzerland LX.PGU02.042 AS5732Z-434G25Mn W7HP64ATCH1 MC UMACbs2 2*2G/250/6L2.2/5R/ CB_bgn_0.3D_HG_IT41 PMDT4300 AS5732Z434G25Mn EMEA Eastern Europe LX.PGU02.
PAGE 190
Model RO Country Acer Part No Description CPU AS5732Z432G32Mn AAP Vietnam LX.PGU0X.008 AS5732Z-432G32Mn EM VHP32ATVN1 MC UMACbs2 1*2G/320/6L2.2/5R/ CB_bgn_0.3D_HG_EN12 PMDT4300 AS5732Z434G50Mn AAP Vietnam LX.PGU0X.006 AS5732Z-434G50Mn EM VHP32ATVN1 MC UMACbs2 2*2G/500_L/6L2.2/5R/ CB_bgn_0.3D_HG_EN13 PMDT4300 AS5732Z434G50Mn AAP Vietnam LX.PGU0X.007 AS5732Z-434G50Mn EM VHP32ATVN1 MC UMACbs2 2*2G/500_L/6L2.2/5R/ CB_bgn_0.3D_HG_EN12 PMDT4300 AS5732Z432G32Mn TWN GCTWN LX.PGU0Y.
PAGE 191
Model LCD VGA Chip VRAM 1 Memory 1 Memory 2 AS5332-902G16Mn N15.6WXGAG UMA N SO1GBII6 SO1GBII6 AS5332-902G16Mn N15.6WXGAG UMA N SO1GBII6 SO1GBII6 AS5332-902G16Mn N15.6WXGAG UMA N SO1GBII6 SO1GBII6 AS5332-302G25Mn N15.6WXGAG UMA N SO1GBII6 SO1GBII6 AS5332-302G25Mn N15.6WXGAG UMA N SO1GBII6 SO1GBII6 AS5332-302G25Mn N15.6WXGAG UMA N SO1GBII6 SO1GBII6 AS5332-302G25Mn N15.6WXGAG UMA N SO1GBII6 SO1GBII6 AS5332-302G25Mn N15.
PAGE 192
Model LCD VGA Chip VRAM 1 Memory 1 Memory 2 AS5332-903G16Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5332-903G16Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5332-903G16Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5332-903G16Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5332-903G16Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5332-903G16Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5332-903G16Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5332-903G16Mn N15.
PAGE 193
Model LCD VGA Chip VRAM 1 Memory 1 Memory 2 AS5732Z-433G50Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5732Z-444G50Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G32Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G25Mi N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G50Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-433G25Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5732Z-433G25Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5732Z-434G25Mn N15.
PAGE 194
Model LCD VGA Chip VRAM 1 Memory 1 Memory 2 AS5732Z-432G25Mn N15.6WXGAG UMA N SO1GBII6 SO1GBII6 AS5732Z-433G25Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5732Z-432G25Mn N15.6WXGAG UMA N SO2GBII6 N AS5732Z-433G25Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5732Z-432G25Mn N15.6WXGAG UMA N SO2GBII6 N AS5732Z-433G25Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5732Z-432G32Mn N15.6WXGAG UMA N SO2GBII6 N AS5732Z-434G50Mn N15.
PAGE 195
Model LCD VGA Chip VRAM 1 Memory 1 Memory 2 AS5732Z-434G25Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G25Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G25Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G25Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-433G32Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5732Z-434G32Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G32Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G32Mn N15.
PAGE 196
Model LCD VGA Chip VRAM 1 Memory 1 Memory 2 AS5732Z-434G25Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G25Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G25Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G25Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G25Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-434G25Mn N15.6WXGAG UMA N SO2GBII6 SO2GBII6 AS5732Z-433G32Mn N15.6WXGAG UMA N SO2GBII6 SO1GBII6 AS5732Z-432G25Mn N15.
PAGE 197
Model 187 HDD 1(GB) HDD 2(GB) ODD Media Processor AS5332-902G16Mn N160GB5.4KS N NSM8XS N AS5332-902G16Mn N160GB5.4KS N NSM8XS N AS5332-902G16Mn N160GB5.4KS N NSM8XS N AS5332-902G16Mn N160GB5.4KS N NSM8XS N AS5332-302G25Mn N250GB5.4KS N NSM8XS N AS5332-302G25Mn N250GB5.4KS N NSM8XS N AS5332-302G25Mn N250GB5.4KS N NSM8XS N AS5332-302G25Mn N250GB5.4KS N NSM8XS N AS5332-302G25Mn N250GB5.4KS N NSM8XS N AS5332-302G25Mn N250GB5.
PAGE 198
Model HDD 1(GB) HDD 2(GB) ODD Media Processor AS5332-903G16Mn N160GB5.4KS N NSM8XS N AS5332-903G16Mn N160GB5.4KS N NSM8XS N AS5332-903G16Mn N160GB5.4KS N NSM8XS N AS5332-903G16Mn N160GB5.4KS N NSM8XS N AS5332-903G16Mn N160GB5.4KS N NSM8XS N AS5332-903G16Mn N160GB5.4KS N NSM8XS N AS5332-903G16Mn N160GB5.4KS N NSM8XS N AS5332-903G16Mn N160GB5.4KS N NSM8XS N AS5332-903G16Mn N160GB5.4KS N NSM8XS N AS5332-903G16Mn N160GB5.
PAGE 199
Model 189 HDD 1(GB) HDD 2(GB) ODD Media Processor AS5732Z-434G50Mn N500GB5.4KS N NSM8XS N AS5732Z-433G50Mn N500GB5.4KS N NSM8XS N AS5732Z-444G50Mn N500GB5.4KS N NSM8XS N AS5732Z-434G32Mn N320GB5.4KS N NSM8XS N AS5732Z-434G25Mi N250GB5.4KS N NSM8XS N AS5732Z-434G50Mn N500GB5.4KS N NSM8XS N AS5732Z-433G25Mn N250GB5.4KS N NSM8XS N AS5732Z-433G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.
PAGE 200
Model HDD 1(GB) HDD 2(GB) ODD Media Processor AS5732Z-432G25Mn N250GB5.4KS N NSM8XS N AS5732Z-432G25Mn N250GB5.4KS N NSM8XS N AS5732Z-433G25Mn N250GB5.4KS N NSM8XS N AS5732Z-432G25Mn N250GB5.4KS N NSM8XS N AS5732Z-433G25Mn N250GB5.4KS N NSM8XS N AS5732Z-432G25Mn N250GB5.4KS N NSM8XS N AS5732Z-433G25Mn N250GB5.4KS N NSM8XS N AS5732Z-432G32Mn N320GB5.4KS N NSM8XS N AS5732Z-434G50Mn N500GB5.4KS N NSM8XS N AS5732Z-434G50Mn N500GB5.
PAGE 201
Model 191 HDD 1(GB) HDD 2(GB) ODD Media Processor AS5732Z-433G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-433G32Mn N320GB5.4KS N NSM8XS N AS5732Z-434G32Mn N320GB5.4KS N NSM8XS N AS5732Z-434G32Mn N320GB5.4KS N NSM8XS N AS5732Z-434G32Mn N320GB5.4KS N NSM8XS N AS5732Z-434G32Mn N320GB5.
PAGE 202
Model HDD 1(GB) HDD 2(GB) ODD Media Processor AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-434G25Mn N250GB5.4KS N NSM8XS N AS5732Z-433G32Mn N320GB5.4KS N NSM8XS N AS5732Z-432G25Mn N250GB5.4KS N NSM8XS N AS5732Z-433G32Mn N320GB5.
PAGE 203
Model 193 Extra SW1 Card Reader Wireless LAN1 Bluetooth AS5332-902G16Mn N 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-902G16Mn N 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-902G16Mn N 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-902G16Mn N 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-902G16Mn N 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-302G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-302G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-302G25Mn McAfee 5 in 1-Bu
PAGE 204
Model Extra SW1 Card Reader Wireless LAN1 Bluetooth AS5332-903G16Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-903G16Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-903G16Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-903G16Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-903G16Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-903G16Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-903G16Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5332-903G16M
PAGE 205
Model 195 Extra SW1 Card Reader Wireless LAN1 Bluetooth AS5732Z-434G50Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G50Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-433G50Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-444G50Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G32Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mi McAfee 5 in 1-Build in 3rd WiFi BG N AS5732Z-434G50Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z
PAGE 206
Model Extra SW1 Card Reader Wireless LAN1 Bluetooth AS5732Z-432G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-432G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-432G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-433G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-432G25Mn N 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-433G25Mn N 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-432G25Mn N 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-433G25Mn N 5
PAGE 207
Model 197 Extra SW1 Card Reader Wireless LAN1 Bluetooth AS5732Z-432G25Mn N 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-433G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-433G32Mn N 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G
PAGE 208
Model Extra SW1 Card Reader Wireless LAN1 AS5732Z-434G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mn McAfee 5 in 1-Build in 3rd WiFi 1x2 BGN N AS5732Z-434G25Mn
PAGE 209
Appendix B Test Compatible Components This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system functions are tested under Windows® Vista and Windows® 7 environments. Refer to the following lists for components, adapter cards, and peripherals which have passed these tests. Regarding configuration, combination and test procedures, please refer to the Aspire 5732Z/5332 Compatibility Test Report released by the Acer Mobile System Testing Department.
PAGE 210
Microsoft® Windows® OS Environment Test Vendor Type Description Adapter DELTA 65W Adapter DELTA 65W 19V 1.7x5.5x11 Yellow ADP-65JH DB A, LV5 LED LF LITE-ON 65W Adapter LITE-ON 65W 19V 1.7x5.5x11 Yellow PA-1650-22AC LV5 LED LF HIPRO 65W Adapter HIPRO 65W 19V 1.7x5.5x11 Yellow HP-A0652R3B 1LF, LV5 LED LF DELTA 65W Adapter DELTA 65W 19V 1.7x5.5x11 Yellow ADP-65JH DB A, LV5 LED LF LITE-ON 65W Adapter LITE-ON 65W 19V 1.7x5.5x11 Yellow PA-1650-22AC LV5 LED LF HIPRO 65W Adapter HIPRO 65W 19V 1.
PAGE 211
Vendor Type Description SIMPLO 6CELL2.2 Battery SIMPLO AS-2009A Li-Ion 3S2P LGC 6 cell 4400mAh Main COMMON LGC 2.2Ah(S3 ) SIMPLO 6CELL2.2 Battery SIMPLO AS-2009A Li-Ion 3S2P SAMSUNG 6 cell 4400mAh Main COMMON SDI 2.2Ah(F) SANYO 6CELL2.2 Battery SANYO AS-2009A Li-Ion 3S2P SANYO 6 cell 4400mAh Main COMMON 2.2Ah(A) SONY 6CELL2.2 Battery SONY AS-2009A Li-Ion 3S2P SONY 6 cell 4400mAh Main COMMON 2.2Ah(G6F) PANASONIC 6CELL2.
PAGE 212
Vendor Type Description PANASONIC 6CELL2.2 Battery PANASONIC AS-2009A Li-Ion 3S2P PANASONIC 6 cell 4400mAh Main COMMON 2.2Ah(CG ) SAMSUNG 6CELL2.2 Battery SAMSUNG AS-2009A Li-Ion 3S2P SAMSUNG 6 cell 4400mAh Main COMMON 2.2Ah(F) SIMPLO 6CELL2.2 Battery SIMPLO AS-2009A Li-Ion 3S2P PANASONIC 6 cell 4400mAh Main COMMON Panasonic 2.2Ah ( CG ) SIMPLO 6CELL2.2 Battery SIMPLO AS-2009A Li-Ion 3S2P LGC 6 cell 4400mAh Main COMMON LGC 2.2Ah(S3 ) SIMPLO 6CELL2.
PAGE 213
Vendor Type Description INTEL PMDT4200 CPU Intel Pentium Dual-Core T4200 PGA 2.0G 1M 800 35W R0 no VT INTEL PMDT4300 CPU Intel Pentium Dual-Core T4300 PGA 2.1G 1M 800 R-0 INTEL PMDT4400 CPU Intel Pentium Dual-Core T4400 2.2G 1M 800 INTEL PMDT4200 CPU Intel Pentium Dual-Core T4200 PGA 2.0G 1M 800 35W R0 no VT INTEL PMDT4300 CPU Intel Pentium Dual-Core T4300 PGA 2.1G 1M 800 R-0 INTEL PMDT4400 CPU Intel Pentium Dual-Core T4400 2.2G 1M 800 SEAGATE N160GB5.4KS HDD SEAGATE 2.
PAGE 214
Vendor 204 Type Description HGST N160GB5.4KS HDD HGST 2.5" 5400rpm 160GB HTS545016B9A300 Panther B SATA LF F/W:C60F WD N160GB5.4KS HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO ML160 SATA LF F/W:11.01A11 SEAGATE N250GB5.4KS HDD SEAGATE 2.5" 5400rpm 250GB ST9250315AS Wyatt SATA LF F/W:0001SDM1 TOSHIBA N250GB5.4KS HDD TOSHIBA 2.5" 5400rpm 250GB MK2555GSX Libra SATA LF F/W:FG001J HGST N250GB5.4KS HDD HGST 2.5" 5400rpm 250GB HTS543225L9A300 Falcon-B SATA LF F/W:C40C HGST N250GB5.
PAGE 215
Vendor Type Description TOSHIBA N320GB5.4KS HDD TOSHIBA 2.5" 5400rpm 320GB MK3255GSX Libra SATA LF F/W:FG011J HGST N320GB5.4KS HDD HGST 2.5" 5400rpm 320GB HTS545032B9A300 Panther B SATA LF F/W: C60F WD N320GB5.4KS HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0 ML160 SATA LF F/W:11.01A11 SEAGATE N500GB5.4KS HDD SEAGATE 2.5" 5400rpm 500GB ST9500325AS Wyatt SATA LF F/W:0001SDM1 HGST N500GB5.4KS HDD HGST 2.5" 5400rpm 500GB HTS545050B9A300 Panther B SATA LF F/W:C60F WD N500GB5.4KS HDD WD 2.
PAGE 216
Vendor 206 Type Description HGST N160GB5.4KS HDD HGST 2.5" 5400rpm 160GB HTS543216L9A300 Falcon-B SATA LF F/W:C40C HGST N160GB5.4KS HDD HGST 2.5" 5400rpm 160GB HTS545016B9A300 Panther B SATA LF F/W:C60F WD N160GB5.4KS HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO ML160 SATA LF F/W:11.01A11 SEAGATE N250GB5.4KS HDD SEAGATE 2.5" 5400rpm 250GB ST9250315AS Wyatt SATA LF F/W:0001SDM1 TOSHIBA N250GB5.4KS HDD TOSHIBA 2.5" 5400rpm 250GB MK2555GSX Libra SATA LF F/W:FG001J HGST N250GB5.
PAGE 217
Vendor Type Description SEAGATE N320GB5.4KS HDD SEAGATE 2.5" 5400rpm 320GB ST9320320AS Crockett SATA LF F/W:0303 TOSHIBA N320GB5.4KS HDD TOSHIBA 2.5" 5400rpm 320GB MK3255GSX Libra SATA LF F/W:FG011J HGST N320GB5.4KS HDD HGST 2.5" 5400rpm 320GB HTS545032B9A300 Panther B SATA LF F/W: C60F WD N320GB5.4KS HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0 ML160 SATA LF F/W:11.01A11 SEAGATE N500GB5.4KS HDD SEAGATE 2.5" 5400rpm 500GB ST9500325AS Wyatt SATA LF F/W:0001SDM1 HGST N500GB5.4KS HDD HGST 2.
PAGE 218
Vendor Type Description SAMSUNG N15.6WXGAG CCFL LCD SAMSUNG 15.6"W WXGA Glare LTN156AT01-A01 LF 220nit 8ms 600:1 LPL N15.6WXGAG CCFL LCD LPL 15.6" WXGA Glare LP156WH1-TLA1 LF 220nit 8ms 400:1 LPL N15.6WXGAG CCFL LCD LPL 15.6"W WXGA Glare LP156WH1-TLA3 LF 220nit 8ms 400:1 CMO N15.6WXGAG LCD CMO 15.6" WXGA Glare N156B3-L02 LF 220nit 8ms AUO N15.6WXGAG LCD AUO 15.6" WXGA Glare B156XW01-V0 LF 220nit 8ms AUO N15.6WXGAG CCFL LCD AUO 15.
PAGE 219
Vendor Type Description NANYA SO1GBII6 Memory NANYA SO-DIMM DDRII 667 1GB NT1GT64UH8D0FN-3C LF 64*16 0.07um MICRON SO1GBII6 Memory MICRON SO-DIMM DDRII 667 1GB MT8HTF12864HDY-667G1 LF 64*16 0.065um SAMSUNG SO1GBII6 Memory SAMSUNG SO-DIMM DDRII 667 1GB M470T2864EH3-CE6 LF 64*16 0.055um HYNIX SO1GBII6 Memory HYNIX SO-DIMM DDRII 667 1GB HYMP112S64CP6Y5 LF HYNIX SO1GBII6 Memory HYNIX SO-DIMM DDRII 667 1GB HMP112S6EFR6CY5 LF 64*16 0.
PAGE 220
Vendor Type Description MICRON SO1GBII6 Memory MICRON SO-DIMM DDRII 667 1GB MT8HTF12864HDY-667G1 LF 64*16 0.065um SAMSUNG SO1GBII6 Memory SAMSUNG SO-DIMM DDRII 667 1GB M470T2864EH3-CE6 LF 64*16 0.055um HYNIX SO1GBII6 Memory HYNIX SO-DIMM DDRII 667 1GB HYMP112S64CP6Y5 LF HYNIX SO1GBII6 Memory HYNIX SO-DIMM DDRII 667 1GB HMP112S6EFR6CY5 LF 64*16 0.055um NANYA SO2GBII6 Memory NANYA SO-DIMM DDRII 667 2GB NT2GT64U8HD0BN-3C LF 128*8 0.
PAGE 221
Vendor Type Description SONY NSM8XS ODD SONY Super-Multi DRIVE 12.7mm Tray DL 8X AD-7580S LF W/O bezel SATA PLDS NSM8XS ODD PLDS Super-Multi DRIVE 12.7mm Tray DL 8X DS-8A3S LF W/O bezel SATA PANASONIC NSM8XS ODD PANASONIC Super-Multi DRIVE 12.7mm Tray DL 8X UJ880A LF W/O bezel SATA HLDS NSM8XS ODD HLDS Super-Multi DRIVE 12.7mm Tray DL 8X GT20N LF W/O bezel SATA SONY NSM8XS ODD SONY Super-Multi DRIVE 12.7mm Tray DL 8X AD-7580S LF W/O bezel SATA PLDS NSM8XS ODD PLDS Super-Multi DRIVE 12.
PAGE 222
Vendor Type Description None UMA UMA (Intel) None UMA UMA (Intel) 512MDDR2(64*16*4) 512M-DDR2 64*16*4 512MDDR2(64*16*4) 512M-DDR2 64*16*4 INTEL GL40(A1) NB Chipset Intel CS GL40NB A1 INTEL GL40(A1) NB Chipset Intel CS GL40NB A1 INTEL GM45 NB Chipset Intel CS GM45NB INTEL GM45 NB Chipset Intel CS GM45NB INTEL GL40(A1) NB Chipset Intel CS GL40NB A1 INTEL GL40(A1) NB Chipset Intel CS GL40NB A1 INTEL ICH9M SB Chipset Intel CS ICH9M INTEL ICH9M SB Chipset Intel CS ICH9M INTEL
PAGE 223
Vendor Type Description WNC PIFA PIFA WNC PIFA PIFA WNC PIFA PIFA Realtek ALC272X Realtek Audio Codec ALC272X Realtek ALC272X Realtek Audio Codec ALC272X Realtek ALC272X Realtek Audio Codec ALC272X Realtek ALC272X Realtek Audio Codec ALC272X Realtek ALC272X Realtek Audio Codec ALC272X Realtek ALC272X Realtek Audio Codec ALC272X Normal wi IMR Normal wi IMR Mirror w/Camera Mirror w/Camera Mirror Mirror Audio Codec A cover Quanta Wistron B cover Mirror w/Camera Mirror w/C
PAGE 224
Vendor 214 Type Description Foxconn 3rd WiFi 1x2 BGN Foxconn Wireless LAN Atheros HB93 1x2 BGN (HM) Foxconn 3rd WiFi 1x2 BGN Foxconn Wireless LAN Atheros HB93 1x2 BGN (HM) Foxconn 3rd WiFi 1x2 BGN Foxconn Wireless LAN Atheros HB93 1x2 BGN (HM) Foxconn 3rd WiFi 1x2 BGN Foxconn Wireless LAN Atheros HB93 1x2 BGN (HM) Foxconn 3rd WiFi 1x2 BGN Foxconn Wireless LAN Atheros HB93 1x2 BGN (HM) Appendix B
PAGE 225
Appendix C Online Support Information This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
PAGE 226
216 Appendix C
PAGE 227
Index A Replacing AFLASH Utility 103 D 37 Antennas DIMM Modules Removing 91 Replacing 94 Removing 55 Replacing 121 Display 4 B display Battery hotkeys 124 Replacing E Battery Pack Removing 50 EasyTouch Failure BIOS Euro ROM type 18 vendor 18 Version 18 15 Flowchart 25–37 Advanced 28 Boot 35 Exit 36 Navigating 25 49 F Features 1 Flash Utility Onboard Device Configuration 31 Power 33 Save and Exit 36 Security 30 System Security 36 37 FPC Cable Removing 89 FRU (Field Replaceable
PAGE 228
Removing 62 Replacing 118 127 No Display Issue Notebook Manager Keyboard Failure 129 14 hotkey num lock L on indicator 10 LCD Bezel O Removing 85 Replacing 100 ODD Failure LCD Brackets Online Support Information Removing 89 Replacing 97 Optical Disk Drive Replacing LCD Cable Removing Removing 63 Replacing 113 Panel 8 PC Card 10 84 LCD Module Reassembly Procedure 94 Power Board Removing 71 Replacing 109 LCD Panel Removing 87 Replacing 97 Left Speaker Module Removing 72 Replacing 108
PAGE 229
T Test Compatible Components 199 Thermal Module Removing 80 Replacing 103 Thermal Unit Failure 136 TouchPad Removing 76 TouchPad Bracket Removing 76 Replacing 105 TouchPad Failure 130 Troubleshooting Built-in KB Failure 129 EasyTouch Buttons 136 HDTV Switch 137 Internal Speakers 130 LCD Failure 129 Modem 136 No Display 127 ODD 133 Other Failures 137 Power On 126 Thermal Unit 136 TouchPad 130 WLAN 136 U Undetermined Problems 138 Upper Cover Removing 67 Replacing 109 utility BIOS 25–37 W Windows
PAGE 230
220