Installation guide
Flush Mount Fixtures
Model: 326960, 326962
, C2F60040LWH, C2F110040LWH
1 of 1
Limited Factory Warranty
American Fluorescent Corporation warrants this fixture is free from defects in materials and workmanship when installed and u
for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of de
not cover failure due to improper installation, misuse, m
Safety Precautions
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with
instructions could result in potentially fatal electric shock and/or
property damage.
It is recommended that a qualified
fixture must be wired in accordance with all national and local
electrical codes.
Do not
handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a wet or damp surface or in water.
ASSEMBLY INSTRUCTIONS
1.
Preparing for installation
A.
Disconnect electrical power
or servicing any part of this fixture.
B.
Carefully remove the fixture from the carton, and check that all parts are
included, as shown in figure below. Be careful not to misplace any of the screws
or parts
which are needed for installing the fixture.
2. Wiring-
all wiring must take place inside junction box.
Caution:
Make sure power is off at fuse or circuit breaker box. Check power
wires for damage or scrapes. If power supply wires are within three inches of
ballast power supply
, use wire suitable for at least
dwellings built before 1985 ha
ve supply wire rated to 60C. Consult a qualified
electrician before installing.
A. Install gem bar (2) on
the junction box by securing it with
(supplied).
B. Install threaded stem (3)
on the
Secure stem with nut (4).
C
. Make all wire connections to appropriate wire. Secure with wire nuts
(supplied).
D
. Connect the green wire from the fixture
wire.
E.
The black wire from the fixture is connected to the black wire from
source.
F.
The white wire from the fixture is connected to the white (neutral) wire from
power source.
G.
Tuck all connections neatly into junction box.
3. Mounting
A.
Install backpan (5) by securing it with decorative nut (6) on the stem (3).
4. Shade-
Secure shade (7) with three screws (8)
5
. Restore power at fuse or circuit breaker box.
Flush Mount Fixtures
, C2F60040LWH, C2F110040LWH
American Fluorescent Corporation warrants this fixture is free from defects in materials and workmanship when installed and u
for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of de
not cover failure due to improper installation, misuse, m
ishandling or damage incurred in transit
Safety Precautions
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with
these
instructions could result in potentially fatal electric shock and/or
It is recommended that a qualified
electrician perform all wiring. This
fixture must be wired in accordance with all national and local
handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a wet or damp surface or in water.
ASSEMBLY INSTRUCTIONS
Preparing for installation
Disconnect electrical power
at fuse or circuit breaker box before installing
or servicing any part of this fixture.
Carefully remove the fixture from the carton, and check that all parts are
included, as shown in figure below. Be careful not to misplace any of the screws
which are needed for installing the fixture.
all wiring must take place inside junction box.
Make sure power is off at fuse or circuit breaker box. Check power
wires for damage or scrapes. If power supply wires are within three inches of
, use wire suitable for at least
90C (194F). Note:
Most
ve supply wire rated to 60C. Consult a qualified
the junction box by securing it with
two (1) screws
on the
gem bar (2), leave 7/16” of stem exposed.
. Make all wire connections to appropriate wire. Secure with wire nuts
. Connect the green wire from the fixture
to the power source green
ground
The black wire from the fixture is connected to the black wire from
The white wire from the fixture is connected to the white (neutral) wire from
Tuck all connections neatly into junction box.
Install backpan (5) by securing it with decorative nut (6) on the stem (3).
Secure shade (7) with three screws (8)
.
. Restore power at fuse or circuit breaker box.
LED Ceiling Fixture
, C2F60040LWH, C2F110040LWH
120VAC / 60Hz
American Fluorescent Corporation warrants this fixture is free from defects in materials and workmanship when installed and u
sed
under normal operating conditions
for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of de
fective fixture or components; it does
ishandling or damage incurred in transit
This fixture is designed for use in a 110
-
Do not use on a dimming circuit.
To reduce the
risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green)
between
this fixture and the ground connection of your main power
supply panel.
This fixture is intended to be used for general
locations only.
at fuse or circuit breaker box before installing
Carefully remove the fixture from the carton, and check that all parts are
included, as shown in figure below. Be careful not to misplace any of the screws
Make sure power is off at fuse or circuit breaker box. Check power
wires for damage or scrapes. If power supply wires are within three inches of
the
Most
ve supply wire rated to 60C. Consult a qualified
two (1) screws
gem bar (2), leave 7/16” of stem exposed.
. Make all wire connections to appropriate wire. Secure with wire nuts
ground
The black wire from the fixture is connected to the black wire from
power
The white wire from the fixture is connected to the white (neutral) wire from
Install backpan (5) by securing it with decorative nut (6) on the stem (3).
LED Ceiling Fixture
120VAC / 60Hz
8060656 R2
under normal operating conditions
fective fixture or components; it does
-
120VAC, 60Hz fused circuit.
risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green)
contact
this fixture and the ground connection of your main power
This fixture is intended to be used for general
indoor lighting in dry