Specification

ManualsBrandsAspect ManualsHome DecorCollage 12 in. x 6 in. Bone Porcelain Peel and Stick Decorative Backsplash in (5-pk/case) 5 sq. ft.

Aspect Collage™ Decorative Tiles Section 09 30 29

Acoustic Ceiling Products, L.L.C. DECORATIVE METAL TILES

May, 2020 Page 1 of 4

MiniSPEC 09 30 29-1 DECORATIVE METAL TILES

Part 1 General

1.1 SECTION INCLUDES

A. Decorative metal [tiles].

1.2 RELATED SECTIONS

A. Section [______-____________]: Wall substrate.

B. Section 09 91 10: Preparation [and priming] of substrate surfaces.

1.3 REFERENCES

A. ASTM E84-07 - Test Method for Surface Burning Characteristics of Building Materials.

1.4 SUBMITTALS FOR REVIEW

A. Section 01 33 00: Submission procedures.

B. Product Data: Provide data on wall [tiles,] [and adhesive.]

C. Shop Drawings: Indicate wall elevations with [] [tile] layout.

D. Samples: Submit [two (2)] [_______] samples of [s] [tiles], < [____x____] mm>

<<[____x____] inch >>in size illustrating , finish, and texture.

1.5 SUBMITTALS FOR INFORMATION

A. Section 01 33 00: Submission procedures.

B. Installation Data: Manufacturer's special installation requirements indicating special

procedures, perimeter conditions requiring special attention, and [________].

1.6 REGULATORY REQUIREMENTS

A. Conform to applicable code for flame and smoke ratings when tested to ASTM E84 Class

C for Matted tiles.

1.7 DELIVERY, STORAGE, AND PROTECTION

A. Section 01 61 00: Transport, handle, store, and protect products.

B. Inspect materials on site to verify acceptance.

C. Store tiles flat in a clean, dry area.

D. Protect materials from temperature cycling.

E. Do not slide against each other or over rough surfaces.

Summary of content (4 pages)

PAGE 1
Aspect Collage™ Decorative Tiles Acoustic Ceiling Products, L.L.C. May, 2020 Part 1 General 1.1 SECTION INCLUDES A. 1.2 Section 09 30 29 DECORATIVE METAL TILES Page 1 of 4 Decorative metal [tiles]. RELATED SECTIONS A. Section [______-____________]: Wall substrate. B. Section 09 91 10: Preparation [and priming] of substrate surfaces. 1.3 REFERENCES A. 1.4 ASTM E84-07 - Test Method for Surface Burning Characteristics of Building Materials. SUBMITTALS FOR REVIEW A.
PAGE 2
Aspect Collage™ Decorative Tiles Acoustic Ceiling Products, L.L.C. May, 2020 1.8 Section 09 30 29 DECORATIVE METAL TILES Page 2 of 4 ENVIRONMENTAL REQUIREMENTS A. Section 01 35 26: Environmental conditions affecting products on site. B. Do not apply materials when surface and ambient temperatures are outside the temperature ranges required by the adhesive manufacturer. C. Maintain these conditions 24 hours before, during and after installation of adhesive applied [s] [tiles]. 1.
PAGE 3
Aspect Collage™ Decorative Tiles Acoustic Ceiling Products, L.L.C. May, 2020 Part 3 Execution 3.1 EXAMINATION Section 09 30 29 DECORATIVE METAL TILES Page 3 of 4 A. Section 01 70 00: Verify existing conditions before starting work. B. Verify that substrate surfaces are [primed and] ready to receive work, and conform to requirements of [] [tile] manufacturer. C.
PAGE 4
Aspect Collage™ Decorative Tiles Acoustic Ceiling Products, L.L.C. May, 2020 3.5 Section 09 30 29 DECORATIVE METAL TILES Page 4 of 4 INSTALLATION A. Install adhesive and metal [s] [tiles] to manufacturer's written instructions and as follows: [OR] B. Apply from inside corner, working outwards and upwards. C. For installation of s around a focal point, build out symmetrically from both sides of the focal point. D. For installation of tiles, peel backing from tile and align into correct position.