Specifications

Comfort Reference Value – 5th Generation of STÖBER Inverters STÖBER
ANTRIEBSTECHNIK
11. Used Parameters
KSW-234
U.. Protection functions
Par. Description Fieldbus-
address
U02
Global
r=3, w=3
Level overtemperature Device i2t: Parallel to the monitoring of the heat dissipater
temperature, an additional protective function is offered via i²t. The device load can be indicated as
a percentage via parameter E22. If the value in E22 is greater than 100%, U02 is triggered.
0: inactive; Device does not react to the triggering of U02.
1: Message; When U02 is triggered, this is only indicated. The device continues to remain ready for
operation.
2: Warning; After expiration of the tolerance time in U03, the device assumes fault status (for E39,
see chap. 17).
3: Fault
; After U02 is triggered, the device immediately assumes fault status (for E39, see chap.
17).
Fieldbus: 1LSB=1; Type: U8; USS-Adr: 15 00 80 00 hex
4802h 0h
U03
Global
r=3, w=3
Time overtemperature Device i2t: Can only be set with U02=2:Warning. Defines the time
during which a trigger of the i²t monitoring is tolerated. After expiration of this time, the device
assumes fault status.
Value range in s: 1.00 ... 10,00 ... 60.00
Fieldbus: 1LSB=0,01s; Type: U8; (raw value:2 Bit=1·s); USS-Adr: 15 00 C0 00 hex
1 Only when the appropriate event level is parameterized to 2:Warning.
4803h 0h
U10
Global
r=3, w=3
Level temperature motor i2t: Parallel to the monitoring of the positor line on the motor, the
inverter simulates the motor temperature via an i²t model. The motor load is indicated as a
percentage in parameter E23. If the value in E23 is greater than 100%, U10 is triggered.
0: inactive; Device does not react to the triggering of U10.
1: Message
; Triggering of U10 is only indicated. The device continues to be ready for operation.
2: Warning; After expiration of the tolerance time U11, the device assume fault status.
Fieldbus: 1LSB=1; Type: U8; USS-Adr: 15 02 80 00 hex
480Ah 0h
U11
Global
r=3, w=3
Time temperature motor i2t: Can only be set when U10=2:Warning. Defines the time during
which a trigger of i²t monitoring is tolerated. After expiration of this time, the device assumes fault
status.
Value range in s: 1.00 ... 30,00 ... 60.00
Fieldbus: 1LSB=0,01s; Type: U8; (raw value:2 Bit=1·s); USS-Adr: 15 02 C0 00 hex
1 Only when the appropriate event level is parameterized to 2:Warning.
480Bh 0h
U12
Global
r=3, w=3
Level motor connection: When the axis switch via POSISwitch
®
is utilized, the inverter can
test during switching whether the contactor of the motor to be switched off has actually broken
contact (opened). In addition, under certain circumstances, it can be determined that no motor is
connected.
0: inactive;
3: Fault
;
Fieldbus: 1LSB=1; Type: U8; USS-Adr: 15 03 00 00 hex
480Ch 0h
U15
Global
r=3, w=3
Level MotorTMP: Trips when the motor temperature sensor on X2 triggers.
2: Warning; After expiration of the tolerance time U16, the device assume fault status.
3: Fault
; The device immediately assumes fault status after the motor TMP is triggered.
Fieldbus: 1LSB=1; Type: U8; USS-Adr: 15 03 C0 00 hex
480Fh 0h
U16
Global
r=3, w=3
Time MotorTMP: Can only be set when U15=2:Warning. Defines the time during which
triggering of the motor TMP is tolerated. After expiration of this time, the device assumes fault
status.
Value range in s: 1.00 ... 2,00 ... 60.00
Fieldbus: 1LSB=0,01s; Type: U8; (raw value:2 Bit=1·s); USS-Adr: 15 04 00 00 hex
1 Only when the appropriate event level is parameterized to 2:Warning.
4810h 0h