Operating instructions

ManualsBrandsASM ManualsPower Tools2730H

309424

Rev. A

Operating Instructions

INSTRUCTIONS

This manual contains important

warnings and information.

READ AND KEEP FOR REFERENCE.

2730B

Model 245347, Series A with Briggs & Stratton 6.5 HP

Motor

2700 psi (186 bar, 18.6 MPa) Operating Pressure

3000 psi (210 bar, 21.0 MPa) Maximum Working

Pressure

2730H

Model 245348, Series A with Honda 6.5 HP Motor

2700 psi (186 bar, 18.6 MPa) Operating Pressure

3000 psi (210 bar, 21.0 MPa) Maximum Working

Pressure

3030

Model 2445349, Series A

3000 psi (210 bar, 21.0 MPa) Operating Pressure

3300 psi (227.5 bar, 22.75 MPa) Maximum

Working Pressure

Table of Contents

Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Component Identification 3. . . . . . . . . . . . . . . . . . . . . . . .

Setup 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pressure Relief Procedure 5. . . . . . . . . . . . . . . . . . . . . . .

Operation 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ASM Warranty 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ASM Phone Number 14. . . . . . . . . . . . . . . . . . . . . . . . . . .

3030 Zip Clean

Model 245349 Shown

ti1025

Related manuals

309425. . . . . . .

Summary of content (14 pages)

PAGE 1
Operating Instructions 309424 Rev. A This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. INSTRUCTIONS 2730B Table of Contents Model 245347, Series A with Briggs & Stratton 6.5 HP Motor 2700 psi (186 bar, 18.6 MPa) Operating Pressure 3000 psi (210 bar, 21.0 MPa) Maximum Working Pressure Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Component Identification . . . . . . . . . . . . . . . . . . . . . . . . 3 Setup . . . . . . . . .
PAGE 2
WARNING FUEL HAZARD The fuel used in this equipment is flammable. When spilled on a hot surface it can ignite and cause a fire. Do not fill fuel tank while engine is running or hot. INJECTION HAZARD Spray from gun, leaks or ruptured components can inject fluid into your body and cause an extremely serious injury, including the need for amputation. Splashing fluid in the eyes or on the skin can also cause serious injury. D Fluid injected into the skin might look like just a cut, but it is a serious injury.
PAGE 3
D Component Identification High Pressure Hose Connection and Garden Hose Connection Pressure Unloader Adjustment Knob On/Off Engine Switch (side) high pressure hose connection garden hose connection Hose Tip Storage Engine Oil Fill Hydraulic Fluid Fill Oil Level Site Gage Gun and wand 309424 3
PAGE 4
Setup Shipping Damage Check the Zip Clean for shipping damage. Notify the carrier immediately if there is any damage. Connect High–Pressure Hose and Gun Connect the high–pressure hose between the pump outlet and gun inlet. Both of these connections are made with quick couplers. CAUTION Up to 100 ft (30 m) of 3/8” high–pressure hose may be used. Longer hoses could affect Zip Clean and chemical injector performance balance. Install Spray Tip Install the spray tip on the wand.
PAGE 5
Pressure Relief Follow these instructions whenever you are instructed to relieve pressure, stop spraying for more than 10 minutes, check or service the equipment, or install or clean the spray nozzle. 1. Engage trigger safety latch. 2. Turn Zip Clean off and remove ignition cable from spark plug. 3. Shut off water supply. Disconnect from water. 4. Remove trigger safety latch and trigger gun to relieve pressure. Then engage the safety latch.
PAGE 6
Operation Startup Always use this startup procedure to ensure the Zip Clean is started safely and properly. D Always engage gun trigger safety latch when you stop spraying. This reduces the risk of fluid injection or splashing in eyes or on the skin if the gun is bumped or triggered accidentally. D Observe all CAUTIONS in this section to avoid costly damage to Zip Clean. . 1. Check engine oil level.
PAGE 7
4. Turn on water supply. CAUTION Be sure water supply is completely turned on before running Zip Clean. Running Zip Clean without water will damage the pump. 5. Trigger the gun until a constant stream of water sprays from the tip indicating the air is purged from the system. 6. Open fuel shutoff valve. Be sure the spark plug ignition cable is pushed firmly onto the spark plug. 7. Put the switch in the ON position and the throttle at HALF throttle.
PAGE 8
. Pull starter rope quickly to start engine. Pull and return rope until engine starts. HINT: Placing one foot on Zip Clean as a brace provides better leverage. NOTE: For easier starting, have one person start Zip Clean while another triggers gun. D If engine is cold, start engine with choke completely closed. In cool weather, you might have to let engine run with choke closed for first 10–30 seconds. In warm weather, open choke completely as soon as engine starts.
PAGE 9
Chemical Injector Operation 1. Follow Pressure Relief Procedure, page 5. 2. Insert chemical filter (attached with clear tubing to chemical injector) into container of chemical. Insert brass coupler into chemical injector. 3. Install the black, large–orifice, chemical tip. (Installing and Changing Spray Tips, page 10). NOTE: The large orifice of chemical tip causes a drop in pressure that actuates chemical injector.
PAGE 10
Installing and Changing Spray Tips Spray tips have 4– or 5–digit numbers on them. The first two digits are the spray angle. Tip holding holes are provided on the chassis including one extra hole for future tip placement. Spray Pattern Fan Angle Spray Tip Number 00XXX 0_ blaster (red) 15XXX 15_ (yellow) 40XXX 40_ (white) Chemical XX_ (black) NOTE: The chemical injector tip is brass and has a large opening and a black plastic cap. 1. Perform Pressure Relief Procedure, page 5. 2.
PAGE 11
Shutdown, Flushing, and Storage D If Zip Clean will be exposed to freezing temperatures, drain all water out of pump. If it must be stored in freezing temperatures, flush Zip Clean with a 50% antifreeze solution, and relieve pressure. Flush Zip Clean before you use it again to remove antifreeze. CAUTION If water freezes in Zip Clean, thaw it in a warm room before you try to start it. Do not pour hot water on or into pump; it could crack the ceramic plungers.
PAGE 12
Sound Data Zip Clean Models So nd Data Sound 2730 Briggs & Stratton Motor 2730 Honda Motor 3030 Sound Pressure 92.5 dB(A) 89.0 dB(A) 93.3 dB(A) Sound Level 106.8 dB(A) 103.3 dB(A) 107.
PAGE 13
Notes 309424 13
PAGE 14
ASM Standard Warranty ASM warrants all equipment referenced in this document which is manufactured by ASM and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized ASM distributor to the original purchaser for use. With the exception of any special, extended, or limited warranty published by ASM, ASM will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by ASM to be defective.