FI DISHWASHER INSTALLATION INSTRUCTIONS ANTs! tructions before T R O P in IM f these o Read all he dishwasher. t g installin AUTOMATIC HIGH LOOP The drain hose is fastened to the back of the machine at the best height. To eliminate potential drain problems, leave this hose in place. CONTENTS INTRODUCTION WHAT YOU NEED SAFETY INSTRUCTIONS XXL DISHWASHERS 2 2 2 4 ADA DISHWASHERS 5 UNIT DIMENSIONS PREPARING THE LOCATION UNIT DIMENSIONS PREPARING THE LOCATION ADAFI TRIM KIT INSTALLATION OPTIONS STEP 1.
Introduction Read these instructions carefully and completely before you install the machine. The installation should be carried out by a qualified person who is familiar with all local codes and ordinances for electrical and plumbing connections. If you are replacing an old dishwasher, you must check the plumbing connection and wiring before you move the new dishwasher into place.
Safety instructions • It is important that you closely follow the instructions provided here. • An incorrect or defective installation can lead to higher consumption of energy, water and dishwashing detergent, which can lead to higher costs and poor cleaning results. • Plumbing and electrical installations must be carried out by qualified professionals.
XXL DISHWASHERS D5524XXLFI, D5534XXLFI, D5554XXLFI, D5894XXLFI UNIT DIMENSIONS Height (Adjustable) U.S. Metric 23-5/8˝ 600 mm 33-7/8˝ to 36˝ Width 860 mm to 914 mm Depth (Includes high loop) 22-7/8˝ 581 mm Weight 110 Ib 50 kg Depth W/Door Open Technical Data 49-1/2˝ Heating element 1200 watt Max loading 4.2 - 140 psi, 0.03-1.0 MPa, 0.
ADA DISHWASHERS D5534ADAFI UNIT DIMENSIONS Height (Adjustable)* U.S. Metric 23-5/8˝ 600 mm 22-7/8˝ 581 mm 108 Ib 49 kg 32-1/4˝ to 34˝ Width Depth (Includes high loop) Depth W/Door Open Weight 819 mm to 864 mm 48-3/8˝ 23-5/8" 600 mm Technical Data 120V, 60Hz, 15 amp Heating element 1200 watt Water pressure 1229 mm Max loading 4.2 - 140 psi, 0.03-1.0 MPa, 0.
ADAFI TRIM KIT INSTALLATION OPTIONS ASKO XLADAFI dishwashers can be installed either with or without accessory fill strips depending on the type of installation. If the dishwasher cutout has been cut to European widths of 23-5/8˝ (600 mm), the unit won’t require fill strips. If the dishwasher cutout is a standard 24˝ (610 mm) wide, we have fill strips that make the unit 24˝ (610 mm) wide.
Step 1. Fitting the dishwasher in place 1. Attach the light shielding film (packed in the document bag) to the underside of the countertop above the touch buttons. (Only certain models). ! 1 The light shielding film ensures optimal button functionality. Note: The surface on which the protective film is to be attached must be clean and dry. 2.
Step 1. Fitting the dishwasher in place 6. Adjust the height of the dishwasher by turning the steel feet with your hands. Leave enough space to adjust them later. 7. Screw in the back foot completely by turning the adjustment screw at the front counterclockwise. Use a flat-bladed screwdriver or a 1/4˝ nut driver. (Only models with front adjustable rear foot). If the machine does not have a front adjustable rear foot, level the remaining rear legs just as you did the front legs. 8.
Step 1. Fitting the dishwasher in place 10. Check that the height of the machine corresponds to the height from the floor to the bottom edge of the counter top. Do not attach the mounting screws. This will be done later. 11. Adjust the back foot by turning the adjustment screw at the front clockwise. (Only models with front adjustable rear foot.) If the machine does not have a front adjustable rear foot, level the remaining rear legs just as you did the front legs. 12.
Step 2. Attaching the accessory door or Custom panel Follow the separate instructions supplied with the dishwasher to attach the chosen accessory door or custom panel to the front of the machine. Note: Once you have fitted the accessory door or custom panel to the dishwasher, the door springs may need adjusting. Check that the door stays in the position in which it is placed. If the door drops down when you open it, the springs need to be tightened.
Step 3. Adjusting the door springs Type A Type B (see page 12) TYPE A 1. The door springs are on the sides of the dishwasher. If necessary, pull out the dishwasher and adjust the tension of the door springs. A good idea is to try adjusting one side only first. Be sure the door is closed. 2. Grab the front end of the spring and pull it up and forward to release it from the forward mount. 3. Loosen the spring from the rear mount by turning it outwards. 4.
Step 3. Adjusting the door springs 5. Replace the back end of the spring by holding the spring at a right angle to the side of the dishwasher and pushing the end of the spring into the hole, then turning the spring in towards the dishwasher. 6. Reattach the front end of the spring by pulling it up and forward to fasten it in the mount. 6 7. Open the door and check the spring tension again. If necessary, make further adjustments as above.
Step 4. Connecting electricity, water, and drain 1. Connect drain hose ASKO provides a 7/8˝ (22 mm) diameter corrugated drain hose which is connected to the back of the unit to form a high loop. NOTE: THREE WAYS TO INSTALL DRAIN CONNECTIONS A) Typical connection to sink plumbing before trap (high loop drain) Do not use any fittings anywhere in the drain line that are less than 7/8˝ (22 mm) OD. The access hole for the drain line should be 1-5/8˝ (41 mm)- 2˝ (50mm) max.
Step 4. Connecting electricity, water, and drain 2. Connect water supply hose In order to prevent heat damage to the inlet valve, all solder connections must be made before the water supply line is connected. Flush the water supply line prior to connecting it to the water fill tube. Shutoff valve The unit has a float switch in the base pan to protect against flooding. If the inlet valve connection is not seated properly, water may leak into the base pan and activate the float switch.
Step 5. Checking dishwasher function and fit Test the dishwasher with the Rinse & Hold program. Check that the dishwasher fills and drains properly. Also check that none of the connections leak. Also check that adjacent drawers and cabinet doors can be opened when the dishwasher door is open. Step 6. Securing the dishwasher 1. 2. 3. 4. Pull out the upper basket, and the center basket if present, and turn the basket stop on the runner outward.
Step 6. Securing the dishwasher 6. Check that the dishwasher’s steel feet are solidly placed on the floor. Make sure the dishwasher is not hanging in the air by the mounting tabs. If it is, turn the front feet to lower them until the machine is resting on the feet. 7. Also adjust the dishwasher’s steel feet so that the dishwasher is level. 8. Tighten the lock nuts on the steel feet with a 5/8 inch (16 mm) open-ended wrench. 5/8" (16 mm) Page 16 Customer Care Center 1-800-898-1879 www.askousa.
Step 7. Attaching the toe kick (if applicable) Type A Type B TYPE A The toe kick is attached with two screws that can only be adjusted vertically. 1. TYPE B Attach the supplied sound insulation material to the back of the toe kick. (Only for certain models.) " 16 9/ m) 3 m 0 (9 2. 3. 4. Loosen the holders for the toe kick by moving the gray catches to the side. Adjust the holders (pull out or push in) until they are on a level with the surrounding kitchen toe kick space.
Step 7. Attaching the toe kick (if applicable) 5. Hang the toe kick on the holders. 6. Check that the toe kick is flush with the surrounding kitchen toe kick. If not, loosen and adjust the holders as necessary until satisfied. Page 18 Customer Care Center 1-800-898-1879 www.askousa.
INSTALLATION CHECKLIST Asko - Dishwasher Appliance Installation Checklist • Remove packaging and check for cosmetic damages. • Remove the information packets from inside the dishwasher. • Attach any accessories as required by the installation. Fill strips, light shielding film, supplied door sealing, accessory door, custom panel... • Attach the drain line using the largest section of the disposer boot allowable. Leave the high loop in place. • Attach the PEX fill hose. Don’t forget to use the O-ring.
Art. No 8092459 Rev. 01 Page 20 Customer Care Center 1-800-898-1879 www.askousa.
