Specifications

Specifications are subject to change without notice. See installation instructions for additional details.
Washer Opening
Vented Dryers
ASKO family-size vented dryers can be vented from the
rear, left or right side. The cabinet cutout illustrated
below gives the dimensions for a rear or left exhaust.
See page 33 for venting requirements.
WARNING ! To reduce the risk of fire, vented dryers must be
exhausted OUTDOORS or the equivalent.
Never cover the end of the dryer stub or vent hose with
anything to catch lint, except for a UL-approved vent bucket.
Condenser Dryers
ASKO condenser dryers must be installed to continuously
drain through a hose attached to the rear of the machine.
To ensure proper drainage, the drain must not be higher
than 40˝ (1016 mm) above the bottom of the dryer.
See page 34 for condensation drain requirements.
NOTE: Condenser dryers require adequate ventilation
for proper operation.
NOTE: A louvered door is recommended for closet installations
using an ASKO condenser dryer.
When HiddenHelper
™
is specified, see pages 41-43. The following
6˝ (152 mm) height HiddenHelpers models are available - HI115,
HDB115 , H B115 .
NOTE:
Exhaust holes
not required for
condenser dryers.
220V 20 Amp
Single Phase
Outlet
Optional
Drain
25˝
(635 mm)
220V 20 Amp
Single Phase
Outlet
Cold Water
Drain
34˝ – 35˝
(864 mm – 889 mm)
15 ¾˝ minimum
(400 mm)
15 ¾˝ minimum
(400 mm)
4
3
/
8
˝
(111 mm)
4 ¾˝
(121 mm)
24˝
(610 mm)
5 ½˝
(140 mm)
5 ½˝
(140 mm)
40˝ to 41˝
(1016 mm – 1041 mm
with 6˝ (152 mm) HiddenHelper
™
)
25˝
(635 mm)
24˝
(610 mm)
34˝ – 35˝
(864 mm – 889 mm)
ASKO´s front controls make it possible to install the washers and dryers
under a cabinet or in a closet. Make sure there is a ¼˝ (6 mm) minimum
clearance between units and between units and cabinet or wall.
Every ASKO washer is delivered ready-fitted with a plug and is intended
for connection to an ASKO dryer, which is equipped with a matching

30 Amp sin gle-phase circuit. When the dryer is on a separate outlet,


single-phase circuit.
PLANNING & DESIGN:

Vented Dryer / Condenser Dryer Opening
NOTE:
Exhaust holes
not required for
condenser dryers.
220V 20 Amp
Single Phase
Outlet
Optional
Drain
25˝
(635 mm)
220V 20 Amp
Single Phase
Outlet
Cold Water
Drain
34˝ – 35˝
(864 mm – 889 mm)
15 ¾˝ minimum
(400 mm)
15 ¾˝ minimum
(400 mm)
4
3
/
8
˝
(111 mm)
4 ¾˝
(121 mm)
24˝
(610 mm)
5 ½˝
(140 mm)
5 ½˝
(140 mm)
40˝ to 41˝
(1016 mm – 1041 mm
with 6˝ (152 mm) HiddenHelper
™
)
25˝
(635 mm)
24˝
(610 mm)
34˝ – 35˝
(864 mm – 889 mm)
Cutout Dimensions
 
 34˝ – 35˝ 864 – 889 mm
w
*
40˝ – 41˝ 1016–1041 mm
 24˝ 610 mm
 25˝ 635 mm
*
Height with 6˝ (152 mm) HiddenHelper
™
installed
NOTE: For these installations, a custom countertop
may be required.
39