I-241W-U User’s Manual with product spec.
History Page Date 2013/01/29 Version V0 Description Initial editing.
Feature Description: Overview 1 Introduction The I-241W-U is a GPON ONT which supports 4 Gigabit Ethernets 2 POTS 2 Wi-Fi (2.4G & 5G) 1 HomePNA 2 USB 1 GPON WAN port (32 GEM ports, 128 TCONTs) Either pure RG model or pure ONT model is supported at one time by downloading different software releases. In this document, we will briefly introduce the feature of pure RG model and pure ONT model. The more detailed information please refers to related documents.
2.1 VoIP The IP Host interface is dedicated for VOIP service. Single VLAN id could be assigned but different p-bits/DSCP could be assigned for SIP control packets and VOIP data. ALU’s SIP protocol is ported for I-241W-U. VOIP related parameters could be configured through OMCI protocol and downloading VOIP XML file to I-241W-U. 2.2 L2 VLAN tagging, VLAN/p-bit transparent and VLAN/p-bit translation are all supported in each Ethernet port and following OLT VLAN modes could be supported.
VOIP service, OLT only configures L2/Multicast information for VEIP interface and leaves routing service to ACS’s business. 3.1 VoIP The same as pure ONT release. Please see section 2.1. 3.2 VEIP The OLT must configure all the VLAN/p-bit used by different services: HSI, IPTV, Management and VOIP. (The VOIP interface is reserved for future ACS-controlled VOIP service. In currently release, it is not supported yet.). Also, the Multicast channel VLAN used for IPTV service.
3.3.1 WAN interface In WAN side, up to 4 WAN connections for following services are supported. HIS: Internet service IPTV: VoD and Multicast service Management: remote management of TR-069 (ACS server) VOIP: ACS controlled VOIP service. (Currently, it’s not supported yet) Only HSI and IPTV interfaces used for routing service for LAN devices. Traffic of other interfaces is terminated in I-241W-U.
to these 2.4G and 5G interface. Visitors can access HSI/IPTV service just like home network by Wi-Fi, but they are forbidden to access I-241W-U management interface. UPnP IGD and DLNA service are not supported for Wi-Fi guest network. 3.4 Multicast service IGMP snooping is supported for home network interface and IGMP proxy is supported in WAN IPTV interface. I-241W-U does not support multicast service on guest network interface.
I-241W-U LED Power [Green Solid] Power on [Green Off] Power off WAN: only for HSI interface [Green Solid] IP connected (the device has a WAN IP address from IPCP/DHCP/Static and Broadband link is is up) and no traffic detected. If the IP or PPPoE session is dropped due to an idle timeout, the light will remain green if PON link is still present. If the session is dropped for any other reason, the light is turned off. The light will turn red when it attempts to reconnect and DHCP or PPPoE fails.
PON connected and ranged, and accepting new provisioning (O5 + OMCI traffic) [Orange Solid] PON registered, but out of service (O6, O7) GE 1-4 [Green Solid] Link up [Green Off] Link down [Green Flash] Activity HomePNA [Green Solid] Link up [Green Off] Link down [Green Flash] Activity VoIP 1-2 Mode A: without registration status [Green Solid] Off-hook [Green Off] On-hook Mode B: with registration status [Green Solid] Registered and On-hook [Green Off] Unregistered [Green Flash] Registered and Off-hook Wi-Fi
[Green Off] WLAN is down or no link connected [Green Flash] WLAN activity WPS 2.
Web interface 4 Introduction The I-241W-U supports the remote management with web browser (IE, Firefox, chrome… etc). 4.1 4.1.1 Supported Device Info General Status Figure 1 4.2 Transceiver Status In this page, you can see temperature, voltage and power.
Figure 2 4.3 UPS status In this page, you can see the status of UPS (Battery, Battery Miss, Battery Replace, Battery Low).
5 Supported ONT 5.1 GPON In this page, you can modify password of GPON and see the status of GPON. Figure 4 5.2 Multicasting In this page, you can see the active group IP address in system.
Figure 5 5.3 IP Host In this page, you can see the status of IP host (IP Address, Subnet Mask, Gateway, DNS Server, Mode, RX Statistic and TX Statistic).
5.4 VEIP In this page, you can see the statistic of VEIP. Figure 7 6 RGW 6.1 WAN 6.1.1 IPv4 In this page, you can add or remove wan connection.
Figure 8-0-1 6.1.1.1 Add WAN - PPPoE Press “Add”.
Figure 8-1-1 Select PPPoE and service type (multiple selections), setting service description, 802.1p, 802.1q, enable DSCP to P-bit, IPv6 (HSI only) and default gateway (HSI only), press “Next”.
Figure 8-1-2 Setting PPPoE username, password, service name, AC name and authentication mode. Setting NAT (HIS only), firewall (HIS only), Dial on demand, Use Static IPv4 Address, Enable PPP Debug Mode, Bridge PPPoE Frames Between WAN and Local Ports, press “Next”.
Figure 8-1-3 Setting DNS server, DNS overwrite, press “Next”. Figure 8-1-4 Checking configuration, press “Apply/Save”.
Figure 8-1-5 Add PPPoE connection complete! Figure 8-1-6 20
6.1.1.2 Add WAN (IPoE) Press “Add”. Figure 8-2-1 Select IPoE, service type (multiple selections), setting service description, 802.1p, 802.1q, enable DSCP to P-bit, IPv6 (HSI only) and default gateway (HIS or IPTV support), press “Next”.
Figure 8-2-2 Select Obtain an IP address automatically, setting option60 and 125 or select Use the following Static IP address, setting WAN IP Address, WAN Subnet Mask and WAN gateway IP Address, press “Next”.
Figure 8-2-3 You can modify configuration of NAT or firewall if service type include HIS or IPTV, press “Next”.
Setting DNS server and DNS overwrite, press “Next”. Figure 8-2-5 Checking configuration, press “Apply/Save”.
Figure 8-2-7 6.1.1.3 Remove WAN connection Select the WAN connection which you want to remove. You can select more then one connections at a time, press “Remove”.
Figure 8-3-1 Remove WAN connection complete! Figure 8-3-2 26
6.1.2 IPv6 This page show IPv6 related information of wan connection. Figure 8-4-1 6.2 LAN 6.2.1 Setting br0 Setting IP address, subnet mask, select DHCP client or DHCP server and setting IP range, press “Apply/Save”.
Figure 9-1-1 Add or remove Static IP Lease List and Reserved IP Address List. Figure 9-1-2 Setting parameters of IPv6.
Figure 9-1-3 You can see the statistic of br0. Figure 9-1-4 6.2.2 Setting br1 (not support IPv6) Setting IP address, subnet mask, select DHCP client or DHCP server and setting IP range, press “Apply/Save”.
Figure 9-2-1 Add or remove Static IP Lease List and Reserved IP Address List. Figure 9-2-2 You can see the statistic of br1.
Figure 9-2-3 6.3 DNS Proxy Setting Host name and Domain name, press “Apply/Save”. Figure 10 6.4 NAT You can set this page if there is at least one wan connection in system which enables NAT. You can set DMZ, press “Apply/Save”.
Figure 11-1 Add or remove Virtual Server and Port Triggering.
6.5 Routing 6.5.1 Default Gateway You can select the interface to be default gateway if service type of this connection is HIS or IPTV. Figure 12 6.5.2 Route In this page, you can add or remove static route.
Figure 13 6.5.3 Neighbor (IPv6 only) In this page, you can add or remove neighbor.
Figure 14 6.5.4 RIP In this page, you can configure IPv4 RIP.
6.6 Firewall 6.6.1 User Control In this page, you can add or remove outgoing IP filter. And you can also add or remove incoming IP filter if there is at least one wan connection which enables firewall and service type is HIS or IPTV. Figure 16 6.6.2 Operator Control In this page, you can see firewall of operator but not support to modify.
Figure 17 6.7 Parental Control 6.7.1 Time Restriction In this page, you can set scheduling of system.
6.7.2 Url Filter In this page, you can set url filter of system. Figure 19 6.8 MAC Filter In this page, you can add or remove allowed MAC for br0 and br1 respectively。 Figure 20-1 Select br0 or br1, input allowed MAC address, press “Add”.
Figure 20-2 Select interface which will refer to allowed MAC address table, press “Apply/Save”. Figure 20-3 6.9 IP Tunnel 6.9.1 IPv6 in IPv4 In this page, you can add or remove IPv4 in IPv6.
