Wireless Router User Manual
Table of Contents 1 Hardware Setup ........................................................................................................... 3 1.1 Getting to know your router ................................................................................. 3 1.2 Unpack Router’s box............................................................................................ 4 1.3 Hardware Features ............................................................................................... 5 1.3.
.2 Router ............................................................................................................... 114 3.2.1 Static Routing ............................................................................................ 114 3.2.2 Dynamic Routing....................................................................................... 116 3.2.3 Multiple NAT ............................................................................................ 117 3.3 TR-069 ...........................
1 Hardware Setup 1.1 Getting to know your router This product is designed for new flagship service: Managed Service Home Router. Managed Service Home Router provides: 1. High performance: Dual-Core ARM up to 1.7G/1GB DDR RAM. Dual-Band wireless up to AC2550 (2.4G 200M * 4 + 5G 433M * 4). Gigabyte 2x WAN/ 4x LAN Ethernet ports. 2. High security: Firewall/VPN supported. 3. Easy to setup: Friendly wizard, visual setup & maintenance (Basic Mode), complete functions (Advanced Mode). 4.
1.2 Unpack Router’s box Open the box and remove the router, cables, and installation guide. Wireless router Ethernet Cable Power Adapter Figure 1. Check the package contents The box contains the following items: Wireless router. AC power adapter (plug varies by region). Ethernet cable. Installation guide. If any items are missing or damaged, please contact your dealer. Please keep original packing materials in case you need to return the product for repairing.
1.3 Hardware Features Before setup please take a moment to become familiar with the label and front, side, and back panels of your router. Pay particular attention to the LED on the front panel. 1.3.1 Front Panel The router front and side panels feature the status LED and buttons as shown in the following figure. Figure 2. Router front view Front panel LED status Off: Blue quick blinking (0.
connection). Red and Blue alternate blinking: Updating firmware (or any scenario where device must not be restarted). Red solid: LED on front of device will dim to low (65%) when there is no settings activity Critical issues (hardware or otherwise). or connectivity issues for 120 hours. If any settings are changed or connectivity issues occur LEDs will return to normal (100%) brightness. 1.3.2 Rear Panel There are slots and buttons shown in the following figure. Figure 3.
WAN Port: Connect a network cable for WAN (Wide Area Network) connection. This connects the Ethernet and other access lines e.g. modem. USB 3.0 Port: Connect a USB Printer, U-Disk or USB drive. For printer and folder sharing, reference Services on page 19. Power Port(DC-IN): Use the bundled AC adapter to connect your router to a power source. 1.4 Position Your Router The router lets you access your network from virtually anywhere within the operating range of your wireless network.
2 Normal User Settings The wireless router contains an intuitive graphical user interface (GUI) based on web, which allows administrator to easily configure its features through a web browser. 2.1 Login 1. Open a web browser, then key in the router’s default IP address: http://192.168.1.1, and click Enter key in the keyboard; 2. On the login webpage, type in its default Username: admin and Password: admin, then click Login button.
On the right top side, there are two command buttons: Change Password and Logout. It’s highly recommended to click the Logout button who locates on the right top side when administrator intends to leave the webpage. When Change Password button has been clicked, the browser will navigate administrator to corresponding webpage.
On this page, administrator should just type in new password in New Password and Retype New Password, then click Apply button. 2.2 Wizard Setup The wizard can navigate administrator to configure basic settings for wireless router, which makes it become easy enough to set up the router. Internet Setup After administrator has clicked the Wizard button, the Internet Setup page will come up. Connection Type: There are 5 kinds of connection type: DHCP, PPPoE, Static, PPTP, and L2TP.
used by cable modem service providers. WAN MAC: MAC address of WAN port. Some ISPs monitor devices’ MAC address who are connecting to their networks, and only these devices with a valid MAC address can be served. If router can’t get access to internet, administrator can do either of the followings: * Contact your ISP and request to update the MAC address associated with your ISP subscription. * Clone or change the MAC address of the new device to match the MAC address of the original device.
password. If you have no idea of the username and password, please contact your ISP. Username: This field is only available when you set the WAN Connection Type as PPPoE, PPTP or L2TP. Password: This field is only available when you set WAN Connection Type as PPPoE, PPTP or L2TP. 3. Click Next. Static: Makes the router use a fixed IP address provided by your ISP. This connection type is often used by ADSL service providers. IP: Assigned by your ISP. Subnet Mask: Assigned by your ISP.
their services, and will disallow Internet connection for invalid MAC addresses. Click Next. Note: All of the parameters in Static IP connection type should be provided by your ISP. If you have no idea of them, please ask the ISP for help. 4. PPTP: A service provided by ISPs which requires a username, a password and/or IP address. Username: This field is only available when you set the WAN Connection Type as PPPoE, PPTP or L2TP.
Gateway: If your WAN connection requires a static IP address, type in the gateway IP address in this field. Connect to DNS Server: Select Yes to let the device connect to a DNS Server automatically, or No to enter DNS address manually below. DNS1 & DNS2: Both present the IP address of the DNS server. If the device can’t communicate with DNS1, it will try to communicate with DNS2. 5. VPN Services: IP address or DNS for VPN server. Click Next.
Network Setup After you have clicked Next icon in Internet Setup page, you comes here. 1. SSID: Name for a wireless network, that’s to say it’s used to identify a wireless network. Wi-Fi devices automatically detect all networks communication range, if they own the key. 2. Key: A password used by router to authenticate wireless connections. 3. When done, click Apply.
Config Overview After click the Apply icon, administrator comes to Config Overview page, which displays a summary of configuration information. If the settings are all correct, administrator should click Apply icon.
2.3 Basic Setup 2.3.1 My Router From the navigation panel, go to Basic > My Router. Note: The Reset Icon in the picture is used to restart/reboot router manually! Wireless: This module is implemented to configure some basic settings for router’s wireless connection. 1. SSID: A unique name that identifies the wireless network.
automatically detect all networks within its communication range. The maximum length of a SSID is 32 characters. 2. Key: A string used for connection authentication. Its length ranges from 0 to 63 characters(letters, numbers or a combination) or from 8 to 64 hex digits. 3. Click Apply. 2.3.2 WPS Setup WPS (Wi-Fi Protected Setup) is a wireless security standard that allows the device easily connect to a wireless network. You can configure the WPS function via the PIN code or WPS button.
Note: Authentication methods supported by WPS are: Open system, WPA-Personal and WPA2-Personal. Not supported methods are: Shared Key, WPA-Enterprise, WPA2-Enterprise and RADIUS. 4. Connection Status 愪 The connection status of WPS. 5. Configured: The configured status of WPS. 6. AP PIN Code: Key in the router's PIN code in the client's WPS utility and configure the network name and security settings. 7.
2.3.3 LAN Setup This module makes it easier for administrator to modify the default LAN IP Address. Steps to modify LAN IP settings: 1. From the navigation panel, go to Basic > My Router. 2. LAN IP: The LAN IP address of the wireless router. Its default value is 192.168.1.1. In IP-based networks, packets are sent to the network devices' specific IP addresses. 3. Subnet Mask: Subnet mask of wireless router. Its default value is 255.255.255.0 4.
2.3.4 WAN Setup Click WAN button to configure the WAN connection settings: 1. Connection Type: Choose the Internet Service type. There are five options are DHCP, PPPoE, Static, PPTP, and L2TP. Consult your ISP if you are unsure what kind of WAN connection type to select. 2. If you select DHCP: WAN MAC: MAC (Media Access Control) address is a unique identifier that identifies your computer or device in the network.
DNS 1 & DNS 2: Either of them indicates IP address of a DNS server. Click Apply. 3. If you select PPPoE: Username: This field is only available when you set the WAN Connection Type as PPPoE, PPTP or L2TP. Password: This field is only available when you set WAN Connection Type as PPPoE, PPTP or L2TP. DNS1 & DNS2: Either of them indicates IP address of a DNS server that wireless router will contact. Click Apply. NOTE: All of the parameters mentioned above are provided.
4. If you select Static, below show the steps to set • IP: If WAN connection requires a static IP address, key in the IP address in this field. • Subnet Mask: If WAN connection requires a static IP address, key in the subnet mask in this field. • Gateway: If WAN connection requires a static IP address, key in the gateway IP address in this field. • DNS 1 & DNS 2: Either of them indicates IP address of a DNS server.
5. If you select PPTP: • Username: This field is only available when you set the WAN Connection Type as PPPoE, PPTP or L2TP. • Password: This field is only available when you set WAN Connection Type as PPPoE, PPTP or L2TP. • Get the WAN IP Automatically: Select Yes to get WAN IP automatically and No to enter IP manually below. • IP: If WAN connection requires a static IP address, key in the IP address in this field.
6. If you select L2TP: Please reference to PPTP above for relevant settings descriptions and enter the required information.
2.3.5 Parental Control Parental Control allows administrator to control the behavior of the router. Steps to set parental control function: 1. From the navigation panel, go to Base > Parental Control. 2. Enable Parental Control: Select On to enable parental control, Select Off to disable parental control.
3. Client Name: Select client from the list. The name in the list stands for the client that is communicating with the router. 4. Client MAC: MAC address of the selected client. Note: Client Name just makes it easier for administrator to distinguish lan-side devices. The Client MAC in fact specify the very device under parental control. 5. Add/Delete: Click or 6. Time Management: Click to add/delete the profile. , then setup the client’s schedule timetable to allow or deny client’s access to Internet.
2.3.6 Services 2.3.6.1 USB Printer Sharing USB Printer sharing allows administrator to plug a USB printer to router’s USB port and set up the print server. Steps to set up USB Printer sharing: 1. From the navigation panel, go to Basic > Service > USB Printer sharing > Add Printer. 2. Plug in the USB interface of the printer to the router. Confirm your printer has been detected and click Continue. 3. Select one of the following modes to install the printer driver, and click Add printer.
the upload button. 4. Printer tab displays whether your printer is operating correctly with the print server, as below. 5. To check whether your printer is working correctly or not, input the LAN address (192.168.1.1) for the printer in Windows Finder. 6. Double-click the printer icon and if you see the status interface as shown below, the installation was successful. If an error message prompts that the driver cannot be found, then return to Add Printer settings and select the correct driver.
7. You can view print status information in the Print Jobs tab. Active: All active jobs, including processing and pending jobs. Processing: The job currently processing/communicating print data. All Jobs: All print jobs. 2.3.6.2 FTP Server FTP Server enables an FTP server to share files from USB disk to other devices via your local area network or via the Internet. This page shows information about the FTP Server. For set up FTP Server, go to Advanced > Servers > FTP Server.
Display information on FTP Server: 1. From the navigation panel, go to Basic > Services > FTP Server. 2. Connect an external USB hard disk drive or USB flash drive to your router, and your device will be displayed here. 3. Enable FTP: Click On/Off to enable/disable Internet access to FTP service. 4. Maximum number of Connections: the maximum number of concurrent connections for the Network Neighborhood or FTP Server. 5.
From the navigation panel, go to Basic > Services > Samba Server. Connect an external USB hard disk drive or USB flash drive to your router, and your device will be displayed here. Enable Share: Click the On/Off to enable/disable Internet access to Samba service. Device Name: Enter a name for your device and you can use this name in your web browser's URL field to quickly access the device as a Network Place service. Work Group: Group name of the router in Network Neighborhood.
2.3.6.4 WebDAV The client can write operations in WebDAV directory with appropriate permissions. This page shows information about the WebDAV Server. To set up WebDAV go to Advanced > Servers > WebDAV. 1. From the navigation panel, go to Basic > Services > WebDAV Server. 2. Connect an external USB hard disk drive or USB flash drive to your router, and your device will be displayed here. 3.
the local area network (default value: 80). 4. HTTPS Access Port: The port to access the WebDAV server for HTTPS protocol in the local area network (default value: 443). 5. Enable Outside Access: Select On/Off to enable/disable access to WebDAV server by wide area network. 6. Outside Access: The port number of external service ports via HTTP (default value: 8080). 7. Outside Access HTTPS: The port number of external service ports via HTTPS (default value: 8443). 8.
your device will be displayed here. 3. Enable DLNA Media Server: Switch DLNA media server on or off. 4. Media Server Name: The DLNA server's name, which will be displayed by the media player such as VLC or Windows Media Player. 5. Safely Remove Disk: Click to safely remove the disk. When the USB disk is ejected successfully, the USB status shows 'No device '. 2.3.6.
2.3.6.7 NFS Network File System Server is used to share the USB disk with clients via network. Clients can mount the remote disk to a local directory for a faster speed than using a Samba server. This page shows information about the NFS Server. To setup NFS, go to Advanced > Servers > NFS. Steps to set NFS: 1. From the navigation panel, go to Basic > Services > NFS. 2. Connect an external USB hard disk drive or USB flash drive to the router, then device’s name will be displayed here. 3.
2.3.7 System The system module allows administrator to configure router. Administrator can change the username and password used to login to the router GUI and other miscellaneous settings such as Time Zone, Auto Logout and NTP Server. Steps to set the System settings: 1. From the navigation panel, go to Basic > System. 2. Username: name used to login router. 3. New Password: New login password for router. 4. Retype New Password: Retype new login password for router. 5.
8. Click Apply. 2.4 Advanced Setup 2.4.1 Network 2.4.1.1 WAN Settings 2.4.1.1.1 Internet Settings Router supports several WAN connection types. Select the type from the WAN Connection Type dropdown menu.
Steps to configure WAN connection settings: 1. From the navigation panel, go to Advanced > Network > WAN > Internet. 2. WAN Connection Type: Choose the Internet Service Provider type. There are 5 options: DHCP, PPPoE, Static , PPTP, and L2TP. If you are unsure which type to select, please consult your ISP. 3. MTU: Maximum Transmission Unit value, which defines the maximum length of a packet. 4. Connect to DNS Server: Allows router to get IP address from the DNS Server automatically.
unset, pppd uses the first discovered one. 15. Additional Pppd Options: Additional command line arguments to pass to the pppd daemon. 16. Host Name: This field allows you to provide a host name for your router. It is usually provided by ISP. 17. MAC Address: MAC address identifies a device in the network. ISPs monitor the MAC addresses of devices that connect to their services, and would disallow Internet connection for new MAC addresses.
Steps to set up DDNS: 1. From the navigation panel, go to Advanced > Network > WAN > DDNS. 2. Enable the DDNS Client: Yes means enable DDNS function, No means disable DDNS function. 3. Server: Select the Supported DDNS provider’s URL from the list. 4. Host Name: Specifies the host name to be updated. 5. User Name or E-mail Address: User name or email address which has been registered an account in a DDNS provider. 6. Password or DDNS Key: Password is your registered account. 7. Click Apply.
systems) to be controlled via an IP-based network with or without a central control unit. Under the help of UPnP, one device can be discovered once it has connected to network, then device can be remotely configured to support P2P applications, interactive gaming, video conferencing, and web or proxy servers. Unlike Port forwarding, UPnP automatically configures the router to accept incoming connections and direct requests to a specific PC on the local network. Steps to set up UPnP 愪 1.
Steps to set up Port Trigger: 1. From the navigation panel, go to Advanced > Network > WAN > Port Trigger. 2. Enable Port Trigger: Check to enable or disable Port Triggering. 3. Well-Known Applications: Select popular games and web services to add to the Port Trigger List. 4. Description: A brief description for application. 5. Trigger Port: When there is incoming data from lan-side application to this port, the Port Trigger mechanism will be activated. 6.
2.4.1.1.5 Port Forward Port forwarding is a method used to direct network traffic from Internet to a specified port. Setting up Port Forwarding allows traffic from outside to get access to specified services provided by lan-side device. NOTE: When Port Forward is enabled, router blocks unsolicited inbound traffic from the Internet and only allows replies from outbound requests from the LAN. The network client does not have access to the Internet directly, and vice versa.
7. Port Range: Defines the range of port in wan side. NOTES: A network makes use of ports in order to exchange data, with each port assigned a port number and a specific task. For example, port 80 is used for HTTP. A specific port can only be used by one application or service at a time. Hence, two PCs attempting to access data through the same port at the same time would fail. For example, you cannot set up Port Forwarding for port 100 for two PCs at the same time.
Port triggering will work even without setting up a specific LAN IP address. Unlike port forwarding, which requires a static LAN IP address, port triggering allows dynamic port forwarding using the router. Predetermined port ranges are configured to accept incoming connections for a limited period of time. Port triggering allows multiple computers to run applications that would normally require manually forwarding the same ports to each PC on the network.
Steps to set up DMZ: 1. From the navigation panel, go to Advanced > Network > WAN > DMZ. 2. Enable DMZ: Check to enable or disable DMZ. 3. IP Address of Exposed Station: LAN IP address of a client who can provide DMZ service. This makes the device with this IP address expose to Internet. Make sure that the server client has a static IP address. 4. Enable IPv6 DMZ: Check to enable or disable IPv6 DMZ. 5.
2.3.1.1.7 NAT Pass Through NAT Pass Through allows a Virtual Private Network (VPN) connection to pass through the router to the network server. Steps to set up NAT Pass Through: 1. To configure NAT Pass Through settings, go to Advanced > Network > WAN > NAT Pass Through. 2. PPTP Passthrough: Enable or disable. Point-to-Point Tunneling Protocol (PPTP) is a method for implementing virtual private networks. 3. L2TP Passthrough: Enable or disable.
protocol suite for securing Internet Protocol (IP) communications by authenticating and encrypting each IP packet of a communication session. 5. SSL Passthrough: Secure Sockets Layer(SSL) is cryptographic protocols that provide communications security over a computer network. 6. RTSP Passthrough: Enable or disable. The Real Time Streaming Protocol (RTSP) is a network control protocol designed for use in entertainment and communications systems to control streaming media servers. 7. H.
2.4.1.2 LAN Settings 2.4.1.2.1 LAN The LAN IP module allows administrator to modify lan-side IP address of the router. Steps to modify the LAN IP settings: 1. From the navigation panel, go to Advanced > Network > LAN > LAN IP. 2. IP Address: The LAN IP address of wireless router. The default value is 192.168.1.1. In IP-based networks, data packets are sent to the network devices' specific IP addresses. 3. Subnet Mask: The LAN subnet mask of wireless router. Its default value is 255.255.255.0 4.
2.3.1.2.2 DHCP Server DHCP server can assign each client an IP address and informs the client of DNS server’s IP, default gateway’s IP and etc. This wireless router can allocate up to 253 IP addresses for lan-side devices. Steps to configure the DHCP server: 1. From the navigation panel, go to Advanced > Network > LAN > DHCP Server. 2. Enable DHCP Server: Enable DHCP server function which allows router to act as a DHCP server to automatically assign IP addresses to network clients.
Server. This field only contains alphanumeric characters and dash symbols. 4. IP Pool Starting Address: Starting address that can be allocated to lan-side devices. 5. IP Pool Ending Address: Ending address that can be allocated to lan-side devices. 6. Lease Time: Defines the time that lan-side devices can use the assigned IP address. When the lease time expires, the network client will either send renew or rebind message to a DHCP server. 7. Default Gateway: IP address of the gateway for LAN. 8.
2.4.1.3 Wireless Settings 2.4.1.3.1 Basic Basic settings allow you to set up the basic wireless settings. Steps to set up the basic wireless settings: 1. From the navigation panel, go to Advanced > Network > Wireless > Basic. Basic 2. Frequency: Select the frequency band to configure. 3. Index: Indicates witch SSID is under setting. Note: At present time, the router supports 8 SSIDs. So, router uses Index parameter to indicate witch SSID is under configuration. 4.
5. SSID: A name whose length is less than 32 characters is used to identify a wireless network. WiFi devices automatically detect all networks within its communication range. 6. Hide SSID: If [Yes] is selected, SSID does not show in site surveys by wireless mobile clients and they can only connect to wireless router by manually entering SSID. 7. Authentication Method: This field enables authentication methods for wireless clients. 8. WPA Encryption: Enable WPA Encryption to encrypt data. 9.
2.4.1.3.2 WPS WPS (Wi-Fi Protected Setup) is a wireless security standard that allows you to easily connect devices to a wireless network. You can configure the WPS function via the PIN code or WPS button. WPS supports the authentication of Open system, WPA-Personal and WPA2-Personal. Not supported: Shared Key, WPA-Enterprise, WPA2-Enterprise and RADIUS. Steps to set WPS: 1. From the navigation panel, go to Advanced > Network > Wireless > WPS. 2. Frequency: Select an operating band (2.
WPA-Enterprise, WPA2-Enterprise, and RADIUS encryption method 4. Connection Status: The connection status of WPS. 5. Configured: The configured status of WPS. 6. AP PIN Code: This is your router’s WPS PIN code. Enter this in the client's WPS utility to make a connection. 7. WPS Method: PIN (Personal Information Number) method requires you to enter a PIN number to establish a wireless connection.
2.4.1.3.3 ACL ACL can be used to allow or disallow one device to send packets. Steps to set up the ACL: 1. From the navigation panel, go to Advanced > Network > Wireless > ACL. 2. Frequency: In the frequency field, select the frequency band that you want to use for the ACL settings. 3. Index: Indicate witch SSID is going to apply ACL rules. 4. SSID Name: A name whose length is less than 32 characters is used to identify a wireless network. 5. Enable MAC Filter: Enable MAC filter or disable. 6.
AP/router, or specifically indicates which MAC addresses can associate with the AP/router. 8. When done, click Apply. 2.4.1.3.4 Professional The Professional module provides advanced configuration options. NOTE: We recommend that administrators use the default settings. In this module, administrator can configure the followings: 1. From the navigation panel, go to Advanced > Network > Wireless > Professional.
2. Frequency: Select the frequency band to configure professional settings. 3. Index: Indicates witch SSID is under setting. 4. SSID: A name whose length is less than 32 characters is used to identify a wireless network. 5. Enable TX STBC: Enables or disables the Space Time Coding Block (STBC) feature, as described in 802.11n specification, in transmitting (TX) direction. 6. Enable RX STBC: Enables or disables the Space Time Coding Block (STBC) feature, as described in 802.
Beamforming.) 15. Click Apply. 2.4.1.3.5 Radio Administrator can set some advanced feature for radio of the router. Steps to set Radio: 1. From the navigation panel, go to Advanced > Network > Wireless > Radio.
2. Frequency: Selecting the frequency band that the router is running. 3. Enable Wireless Scheduler: Switch wireless schedule on or not. 4. Date to Enable (Weekdays): Select weekdays to enable Wi-Fi. 5. Time of Day To Enable: Set weekday time to enable Wi-Fi. 6. Date to Enable (Weekend): Select weekend days to enable Wi-Fi. 7. Time of Day To Enable: Set weekend time to enable Wi-Fi. 8. Enable Radio: Select [Yes] to enable wireless radio (wireless network).
second). Lower the Beacon Interval to improve transmission performance in unstable environment or for roaming clients, but it will be power consuming. 18. AMPDU Aggregation: Enables or disables Tx AMPDU aggregation for the entire interface. Receiving aggregate frames will still be performed, but no aggregate frames will be transmitted if this is disabled. 19. VHT AMPDU Aggregation: Set VHT capability field, Maximum A-MPDU length exponent. Value range is 0 to 7.
Steps to set Guest module: 1. From the navigation panel, go to Advanced > Network > Wireless > Guest. 2. Enable Guest: Enable/disable the guest SSID. 3. SSID: Name of the Guest wireless network. 4. Authentication Method: Choose way to exchange authentication data. 5. WPA Encryption: Choose the encrypting method. 6. Network Key: Key used to encrypt the authentication data. 7. When done, click Apply.
2.4.1.4 IPv6 The module is used to set some basic functions related to IPv6. For IPv6 service is not yet widely available, contact your ISP to make sure whether IPv6 service is provided. Steps to set up IPv6: 1. From the navigation panel, go to Advanced > Network > IPv6.
2. Connection Type: Select IPv6 connection type to configure Disable, Native, Static IPv6. 3. 4. 5. 6. DHCP-PD: Dhcpv6 prefix delegation. WAN IPv6 Address: Set the wan interface’s ipv6 address. WAN Prefix Length: Set the wan interface’s ipv6 prefix length. WAN IPv6 Gateway: Set the wan interface’s ipv6 gateway 7. WAN IPv6 MTU: Set the WAN interface’s IPv6 MTU (Maximum Transmission Unit). 8.
22. IPv6 DNS Server 1: IPv6 address for DNS server. 23. IPv6 DNS Server 2: IPv6 address for DNS server. 24. IPv6 DNS Server 3: IPv6 address for DNS server. 25. Port Ranges Valid for Port Forwarding: The "port ranges" are set by Map-T mode, and the port setting for port forwarding must be in these ranges. 26. Click Apply.
2.4.1.7 Parental Control Refer to 2.3.5 Parental Control for relevant setting descriptions. 2.4.1.8 Multicast Enable multicast. The sender and receiver achieve a point to multipoint connection. Steps to set up Multicast: 1. From the navigation panel, go to Advanced > Network > Multicast. 2. IPv4 Multicast Route: Select an IPv4 Multicast Route.
3. IPv6 Multicast Route: Select an IPv6 Multicast Route. *MLD Proxy: The MLD proxy is used in IPv6 environments. This feature enables a device to learn proxy group membership information, and forward multicast packets based upon that information. If a device is acting as RP for route proxy entries, MLD membership reports for these entries can be generated on user specified proxy interface. 4. Enable IGMP/MLD Snooping: Check [Yes] to enable snooping and Check [No] to disable snooping.
2.4.1.9 Routing This module can be used to build a static NAT table between WAN IP address and LAN IP address. Steps to set up Routing: 1. From the navigation panel, go to Advanced > Network > Routing. 2. Enable 1:1 NAT: Check [Yes] to enable this function, check [No] to disable this function. 3. Name: A brief description for application. 4. Public IP: IP address from Charter supplied public IP subnets. 5.
2.4.2 Services 2.4.2.1 USB Printer sharing Refer to 2.3.6.1 USB Printer sharing for relevant setting descriptions. 2.4.2.2 FTP Server FTP Server enables an FTP server to share files from USB disk to other devices via your local area network or via the Internet. To set up FTP Server: 9. From the navigation panel, go to Advanced > Services > FTP Server. 10. Connect an external USB hard disk drive or USB flash drive to the router, and your device will be displayed here. 11.
To create a new account: 1. Add new account. 2. In the Account and Password fields, key in the name and password of your network client. Retype the password to confirm. Click Add to add the account to the list. To add a folder: 1. Add new folder. 2. Enter a folder name. The folder that you created will be added to the folder list. To set up permissions on the folder for FTP server: 1.
2.4.2.3 Samba Samba Share allows you to set up the accounts and permissions for the Samba service. To set up Samba: 1. From the navigation panel, go to Advanced > Services > Samba Server. 2. Connect an external USB hard disk drive or USB flash drive to the router, and your device will be displayed here. 3. Click On/Off to enable/disable Internet access to Samba service. To create a new account: 1. Add new account. 2.
1. Add new folder. 2. Enter a folder name. The folder that you created will be added to the folder list. To set up permissions on the folder for Samba server: 1. From the list of folders, choose one of the shared folders and add the share name, and choose the type of access permission that you want to assign for specific users: 2. R/W: Select this option to assign read/write access. R: Select this option to assign read-only access.
2.4.2.4 WebDAV The client can write operation in WebDAV directory with appropriate permissions. To set up WebDAV: 1. From the navigation panel, go to Advanced > Services > WebDAV Server. 2. Connect an external USB hard disk drive or USB flash drive to your router, and your device will be displayed here. 3. Click On/Off to enable/disable Internet access via WebDAV. To create a new account: 1. Add new account. 2.
1. Add new folder. 2. Enter a folder name. The folder that you created will be added to the folder list. To set up permissions on the folder for WebDAV server: 1. From the list of folders, choose one of the shared folders and add the share name, then choose the type of access permission that you want to assign for specific users: 2. R/W: Select this option to assign read/write access. R: Select this option to assign read-only access. Click Save Permission to apply the changes.
2.4.2.5 DLNA DLNA (Digital Living Network Alliance) allows you to share audio, image and video. Your router allows DLNA-supported devices to access multimedia files from the USB disk connected to your router. To set up DLNA: 1. From the navigation panel, go to Advanced > Services > DLNA Server. 2. Enable DLNA Media Server: Switch DLNA media on or off. 3. Media Server Name: The DLNA server's name, which will be displayed by the media player, such as VLC or windows media player. 4.
that will be shared by the DLNA server. 6. Media Server Directory: The folders that will be shared by the DLNA. 7. Shared Content Type: The media type that will be shared by the DLNA server: audio, image, video. 8. Safely Remove Disk: Click to safely remove the disk. When the USB disk is ejected successfully, the USB status shows 'No device '. 9. Click Apply. 2.4.2.
1. Add new account. 2. In the Account and Password fields, key in the name and password of your network client. Retype the password to confirm. Click Add to add the account to the list. To add a folder: 1. Add new folder. 2. Enter a folder name. The folder that you created will be added to the folder list. To set up permissions on the folder for AFP server: 1.
2.4.2.7 NFS Network File System Server is used to share the USB disk with clients via network. Clients can mount the remote disk to a local directory for a faster speed than using a Samba server. To setup NFS: 1. From the navigation panel, go to Advanced > Services > NFS Server. 2. Connect an external USB hard disk drive or USB flash drive to your router, and your device will be displayed here. 3. Enable NFS: Enable or disable NFS service.
with "read and write" permission. 2) Allows two clients to access the shared partition. The client with IP address 192.168.1.2 has "read only" permission, and the client with IP address 192.168.1.3 has "read and write" permission. > 192.168.1.2,ro;192.168.1.3,rw 3) Allows all clients to access the destination shared partition with the "read only" permission. > *,ro 5. Safely Remove Disk: Click to safely remove the disk. When the USB disk is ejected successfully, the USB status shows 'No device '.
NOTE: Before setting up a VPN connection, you need the IP address or domain name of the VPN server you are trying to access. Steps to set up access to PPTP VPN server: 1. From the navigation panel, go to Advanced > Security > VPN > PPTP VPN Server. Enable VPN Server: enable or disable PPTP VPN Server. VPN Details: The details of PPTP VPN Server. Select General or Advanced settings. Username and Password: The user information of PPTP VPN Server.
Connect to WINS Server Automatically: WINS of PPTP clients. MRU/MTU: The Maximum Receive Unit (MRU) or Maximum Transmission Unit (MTU) sizes are sent to the client as part of the PPTP parameters to use during the PPTP session. We recommend that you do not change MTU or MRU values unless you are sure the change corrects a known problem with your PPTP sessions. Incorrect MTU or MRU values cause traffic through the PPTP VPN to fail. Client IP Address: The IP address range of PPTP clients.
Advanced settings. Username and Password: The user information of OpenVPN server. Input the user name and password for the VPN server and click the 2. button. Advanced VPN server settings: Interface Type: "TUN" will create a routed IP tunnel, "TAP" will create an Ethernet tunnel. Protocol: TCP or UDP server. Server Port: The TCP/UDP port which OpenVPN server will listen on. Firewall: Firewall configuration for VPN server.
Username / Password Auth. Only: Yes requires only username and password for authentication, No also requires authentication certificate. Extra HMAC Authorization: If enabled, a tls_auth key will be used on the server. Every client must also have the key. VPN Subnet / Subnet Mask: VPN subnet and subnet mask settings. Poll Interval: The interval time for crontab of VPN server starting.
2.4.3.1.3 VPN Client View the VPN server list and add profiles. There are three types of VPN servers: PPTP, L2TP and OpenVPN. Steps to setup a VPN Client: 1. From the navigation panel, go to Advanced > Security > VPN > VPN Client. 2. VPN Sever list is displayed. Click Add Profile to set up VPN Client. 3. VPN Server List: Current VPN Services which have been configured. 4. VPN Type: Type of VPN Server access such as PPTP, L2TP and OpenVPN. 5.
7. VPN Server: VPN Server IP address or URL. 8. Username: VPN authentication username. 9. Password: VPN authentication password. 10. PPTP Options: PPTP Encryption method. Select Auto for automatic Microsoft Point-to-Point Encryption (MPPE) and select No Encryption to disable MPPE. Select MPPE 40 for 40-bit MPPE with PPTP Server and select MPPE 128 for 128-bit MPPE with PPTP Server. 11. When done, click Confirm.
2.4.3.2 IPv4 Firewall Enable the firewall to protect local area network against attacks from outside. Firewall filters the incoming and outgoing packets based on rules. NOTE: Firewall is enable by default. 2.4.3.2.1 Common Steps to set up basic Firewall settings: 1. From the navigation panel, go to Advanced > Security > IPv4 Firewall > Common. 2. Enable Firewall: Disabling the firewall will deactivate all related functions. 3.
router. Check No to deny IGMP packages. 6. Click Apply. 2.4.3.2.2 Net Service Filter Under the help of this module, administrator can set black list to block certain services, or set white list to let some services to pass through the router. Steps to set Net Service Filter 愪 1. From the navigation panel, go to Advanced> Security> IPv4 Firewall> Net Service Filter. 2. Enable Net Service Filter: Enable or disable this module. 3.
address such as "192.168.122.1"; (b) enter IP addresses within one subnet or within the same IP pool such as "192.168.123.*" or "192.168.*.*"; or (c) enter all IP addresses as "*.*.*.*". 6. Port Range: For source or destination port range, you can either: a) enter a specific port, such as "95"; or b) enter ports within a range such as "103:315", ">100", or "<65535". 7. Destination IP: For source or destination IP address, you can: (a) enter a specific IP address such as "192.168.122.
2.4.3.2.3 Client ACL This module is used by administrator to prevent router from routing packets which are from specified lan-side devices. Steps to set up Client ACL 愪 1. From the navigation panel, go to Advanced> Security> IPv4 Firewall> Client ACL. 2. Enable Client ACL: Enable or disable Client ACL function. 3. Client: MAC address of lan-side devices. 4. Add/Delete: Click 5. When done, click Apply. or to add/delete the profile.
2.4.3.3 IPv6 Firewall 2.4.3.3.1 Common Steps to set up common IPv6 Firewall: 1. From the navigation panel, go to Advanced > Security >IPv6 Firewall > Common. 2. Enable Firewall: Disabling the firewall will deactivate all related functions. 3. Respond to Ping Request from WAN: This feature allows router to make a response to ping request from WAN. 4. Enable MLD: Check [Yes] to allow MLD packages to be transferred to the router. Check [No] to deny MLD packages. 5. Click Apply.
2.4.3.3.1 IPv6 Firewall All outbound traffic coming from lan-side IPv6 hosts is allowed, as well as related inbound traffic. Any other inbound traffic must be specifically allowed here. You can leave the remote IP empty to allow traffic from any remote host. A subnet can also be specified. Steps to set up IPv6 Firewall: 1. From the navigation panel, go to Advanced > Security > IPv6 Firewall > IPv6 Firewall. 2. Enable Service Firewall: Enable or disable the IPv6 firewall.
7. Port Range: Port range accepts various formats such as Port Range (300:350), individual ports (566,789) or Mix (1015:1024, 3021). 8. Protocol: The protocol the service uses to transport the packages e.g. (UDP, TCP). 9. ICMPv6 Message Type: Make router process the defined types of ICMPv6 packet from specified host. 10. Local Host: IPv6 address of the host. 11. Add/Delete: Click or to add/delete the profile. 12. When done, click Apply. 2.4.
1. From the navigation panel, go to QoS > Prio Mark > SSID. 2. SSID: Choose the name of t Wi-Fi which is going to provide QoS service. 3. DSCP Value: Its value is used to indicate the priority for uploading data. 4. WMM: Its value is used to indicate the priority for downloading data. 5. Click to add this item to the SSID Mark List. 6. Click Apply.
2.4.4.1.2 Server For different remote servers, this setting can let the connections get different priorities. Steps to set up : 1. From the navigation panel, go to QoS > Prio Mark > Server. 2. Server IP: IP address of remote server. 3. DSCP Value: It’s value is used to indicate priority of connections to the responding server. 4. Click to add this item to the Server Mark List. 5. Click Apply.
2.4.4.1.3 Client Steps to set up : 1. From the navigation panel, go to QoS > Prio Mark > Client. 2. Client: MAC address of the lan side device. 3. DSCP Value: It’s value is used to indicate priority of connections to the lan-side device. 4. Click to add this item to the Server Mark List. 5. Click Apply.
2.4.4.1.4 Application Steps to set up : 1. From the navigation panel, go to QoS > Prio Mark > Application. 2. Application: The name of application that is going to use QoS. 3. DSCP Value: It’s value is used to indicate priority of application. 4. Click to add this item to the Server Mark List. 5. Click Apply. 2.4.4.2 Speed Limit This module makes it possible for user to limit the speed of downloading and uploading respectivly.
Steps to set up Speed Limit: 1. From the navigation panel, go to QoS > Speed Limit. 2. Enable Upload Limit: . Check [Yes] to enable upload speed limit and Check [No] to disable upload speed limit. 3. Upload Speed: The highest speed that the router can provide for data uploading. 4. Enable Download Limit: Choose the wifi that is going to provide QoS. 5. Download Speed: The highest speed that the router can provide for data downloading. 6. Click Apply.
1. From the navigation panel, go to Advanced > QoS > Airtime Fairness. 2. Enable ATF: Enable or disable. ATF require primarily focuses on scheduling fairness for transmission of traffic from Access Point (AP), and efficient Wi-Fi bandwidth utilization. 3. Frequency: In the frequency field, select the frequency band that you want to use for the ATF settings. 4. ATF mode: Airtime Fairness implements 2 scheduling algorithms: strict-queue and fair-queue algorithm, which are mutually exclusive.
2.4.5 Admin 2.4.5.1 System The System page allows you to configure your wireless router settings. Steps to set System: 1. From the navigation panel, go to Advanced > Admin > System. 2. Username: Router’s login name. 3. New Password: New password.
4. Retype New Password: Retype new password. 5. Enable SSH Access from WAN: Enable or disable SSH connection from WAN port. 6. Enable SSH Access from LAN: Enable or disable SSH connection from LAN port. NOTE: Three SSH accounts can be used to login the router. 1. Admin: username and password are: admin, admin 2. Operator: username and password are: operator, operator 3. Root: username and password are: root, MmvGB^RY3# 7.
2.4.5.2 Configuration Steps to save/reset/restore router’s configuration: 1. From the navigation panel, go to Advanced > Admin > Configuration. 2. Click Save, and then the browser will automatically download router’s setting files. 3. Click Reset to Default, this will this resets all settings to factory default settings. 4. Click to select setting file, the click Upload button, this will make the router to be set.
2.4.5.3 Log System Log contains logs on network activities in the router. Steps to set router’s log: 1. From the navigation panel, go to Advanced> Admin> Log. 2. Clear: Clear contents in log file. 3. Save: Download log file from router. 4. Refresh: Refresh the log window to show the latest log.
2.4.6 Tools 2.4.6.1 Diagnostic Tools Various diagnostic tools are available such as ping, ping6, traceroute and nslookup. Steps to use Diagnostic Tools: 1. From the navigation panel, go to Advanced> Tools> Diagnostic Tools 2. Method: Choose a specified method to test network. 3. Target: Choose target for the test. 4. Count: Number of times to test. 5. Click Diagnose.
2.4.6.2 Wake on LAN Wake on LAN is a power management function. It allows network admins to wake up LAN side devices from standby or hibernation mode. This function requires motherboard support on LAN-side devices. Steps to set Wake on LAN: 1. From the navigation panel, go to Advanced> Tools> Wake on LAN. 2. Target: Enter the MAC address of the device to be woken up, or select the device name from the list. 3. Device Name: Name of device. 4.
2.4.7 Status 2.4.7.1 System Information System Information displays basic System, WAN, LAN and USB information. From the navigation panel, go to Advanced > Status > System Information.
2.4.7.2 Wireless Wireless shows status information for wireless clients. From the navigation panel, go to Advanced > Status >Wireless . 2.4.7.3 DHCP Lease Show DHCP Lease status information, including MAC, IP and Hostname information. From the navigation panel, go to Advanced > Status > DHCP Lease.
2.4.7.4 Routing Table Show IPv4 and IPv6 routing table and status information. From the navigation panel, go to Advanced > Status > Routing Table.
2.4.7.5 Port Forwarding This module is used to show port forwarding status information. From the navigation panel, go to Advanced > Status > Port Forwarding.
2.4.7.6 Connection List Show active connections status information. From the navigation panel, go to Advanced > Status > Connection List. 2.4.7.7 IPv6 Information Shows details on WAN and LAN IPv6 information. From the navigation panel, go to Advanced > Status > IPv6 Information.
2.4.7.8 Snooping Table Displays snooping table for client joins/leaves for both wired and wireless client streams. From the navigation panel, go to Advanced > Status > Snooping Table.
2.4.7.9 Current Users Display current user who is permitted to get access to Internet through the router. From the navigation panel, go to Advanced > Status > Current User Table. 2.4.7.10 Blocked Users Display current users who are not permitted to get access to Internet through the router. From the navigation panel, go to Advanced > Status > Blocked User.
113
3 Root User Settings You can login to the GUI as a root user for more configuration options. Root user settings are hidden and cannot be configured by normal users. 3.1 Login Root user of the router owns more privilege than Normal User. Following shows the steps to log in Root User’s GUI: 1. Open a web browser and enter IP address: http://192.168.1.1/a43edc96b945ff5d3c624838b54bf3f2/813dbdb6be123e5/ca6 c40542f5e7c4a59f66ca01028597a/login.html. 2.
be useful when there are several devices who are connecting with router. Steps to set Static Routing: 1. From the navigation panel, go to Root > Router > Static Routing. 2. Enable Static Routes: Select [Yes] to enable static routes. 3. Network/Host IP: The destination network or host of a route rule. It could be a host address such as '192.168.123.11' or a network address such as '192.168.0.0'. 4. Subnet Mask: Indicates how many bits are for network ID and subnet ID.
3.2.2 Dynamic Routing Dynamic routing means router can automatically maintain its routing table. Dynamic routing has two basic functions: maintain routing table, and exchange routing table with other routers. Steps to set up Dynamic Routing: 1. From the navigation panel, go to Root > Router > Dynamic Routing. 2. RIP Key Authentication: Enable or disable RIP key authentication mechanism when switching route with other routers. 3. RIP Key Chain: RIP key name. 4. RIP Key 0: RIP key value of RIP Key 0.
10. RIPDefaultGateway: Gateway IP for RIPIP 11. On/Off: Enable or disable this item rule. 12. When done, click Apply. 3.2.3 Multiple NAT This can let you limit range of ipaddress that is going to use NAT function. Steps to set Multiple NAT: 1. From the navigation panel, go to Root > Router > Multiple NAT. 2. Enable Multiple NAT: Check [Yes] to enable this function, Check [No] to disable this function. 3. Name: The name for the item bar. 4. Public IP: IP address that Host IP will be mapped to. 5.
3.3 TR-069 TR-069 is a technical standard defined by DSL forum. Its full name is CPE WAN management protocol. This module can provide a general framework and protocol to a centralized router from remote Internet for next-generation network-management family equipment configuration. Steps to set TR-069: 1. From the navigation panel, go to Root > TR-069. 2. Enable Remote Management: Enable or disable TR-069 remote management. 3.
the ACS using the CPE WAN Management Protocol. This username is used only for HTTP-based authentication of the CPE. 6. Password: Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This password is used only for HTTP-based authentication of the CPE. 7. Periodic Inform Interval: An absolute time reference in UTC to determine when the CPE will initiate the periodic Inform method calls.
Steps to set operating mode: 1. From the navigation panel, go to Root > Operation Mode 2. Select the mode that you want the router to run. 3. Click Apply. 3.4.1 Wireless Router Mode In wireless router mode, the router connects to the Internet via PPPoE, DHCP, PPTP, L2TP or Static IP and shares the wireless network to LAN clients or devices. In this mode, NAT, firewall, and DHCP server are enabled by default. UPnP and Dynamic DNS are supported for SOHO and home users.
Steps to set up Access Point mode: 1. Click Apply, go to Wizard > Internet setup. IP Address: The LAN IP address of wireless router. The default value is 192.168.1.1. In IP-based networks, data packets are sent to the network devices' specific IP addresses. Subnet Mask: The LAN subnet mask of wireless router. The default value is 255.255.255.0 DNS Server 1 & DNS Server 2: Either indicates the IP address of DNS server that the wireless router will contact. Click Next. 2.
be asked to enter the security key. When done, click Apply. 3. To display the new configuration information click Apply. 3.4.3 Media Bridge Mode Media Bridge mode provides a fast 802.11ac Wi-Fi connection for multiple media devices such as computer, Smart TV, game console, DVR, or media player simultaneously, via Ethernet cable. To set up the Media Bridge mode, you need two devices: one configured as a Media Bridge and the other as a router.
To set up Media Bridge mode: 1. Click Apply, go to Wizard > Internet setup. Select the wireless network to connect your media bridge to and enter the password. When done, click Connect. 2. Input LAN IP information and click Apply. IP Address: The LAN IP address of wireless router. The default value is 192.168.1.1. In IP-based networks, data packets are sent to the network devices' specific IP addresses. Subnet Mask: The LAN subnet mask of wireless router. The default value is 255.255.255.
server that the router will contact. 3. To display the new configuration information click Apply.
3.5 Admin 3.5.1 System Through this module, administrator can change admin’s password, root’s login password and operator’s password . Steps to change the router login password: 1. From the navigation panel, go to Root > Admin. 2. New Password: Enter the new password you wish to use. 3. Retype New password: Retype your new password for confirmation. 4. When done, click Apply.
3.5.2 Firmware This module enable administrator to upgrade firmware through web. Steps to upgrade firmware: 1. From the navigation panel, go to Root > Admin > Firmware. 2. New Firmware File: Click to locate the firmware file. 3. Click Upload.
3.6 DFS Test Mode This module is used to test wireless switch. 1. From the navigation panel, go to Root > DFS Test Mode. 2. Test Mode: Enable or disable DFS test mode. 3.9 Fast Roaming Set up fast roaming for smooth client roaming between SSIDs. Steps to set up Fast Roaming: 1. From the navigation panel, go to Root > Fast Roaming. 2. Freq: Select 2.4GHz or 5GHz WiFi frequency to configure. 3. Index: Select which index to configure. 4. Enable 11r: Enable or disable 11r (Fast Roaming). 5.
6. AP BSSID (MAC): Your/our AP’s MAC Address. 7. AP2 BSSID (MAC): Other AP’s MAC Address. 8. NAS Identifier: NAS ID of AP.
3.10 Coverage Coverage allows automatic network switching according to the strength of the signal (2.4GHz or 5GHz) to maintain optimum signal condition. Steps to set up Coverage: 1. From the navigation panel, go to Root> Coverage. 2. Basic Settings: Band Steering Enable: Enable or disable load balancing logic. Whole Home Coverage brings some new steering mechanisms and algorithms in the Load Balancing Daemon (lbd) to handle more scenarios and make use of features supported on newer Wi-Fi devices.
single SSID. 3. Station Database: Include Out-of-Network Devices: Whether out of network devices should be included in the database or not. Mark Adv Client As Dual Band: Whether mark advertisement client as daul band should be included in the database or not. 4. Idle Steering Settings: 5G RSSI steering (dB): RSSI value indicating a node associated on 5GHz should be steered to 2.4GHz (dB). 2.4G RSSI steering (dB): RSSI value indicating a node associated on 2.
6. Offloading Settings: New report time avg (s): Time to average before generating a new utilization report (s). 2.4G overload limit %: Medium utilization threshold for an overload condition on 2.4GHz (%). 5G overload limit %: Medium utilization threshold for an overload condition on 5GHz (%) 2.4G active steering %: Medium utilization safety threshold for active steering to 2.4GHz (%).
Legacy steering wait (s): Time to wait before steering a legacy client again after completing steering (s). BTM steering wait (s): Time to wait before steering a client via BTM again after completing steering without sending an auth reject (s). 8. Basic Advanced: Recent measurement (s): Maximum number of seconds elapsed allowed for a 'recent' measurement. 9.
Out-of-network max (s): Max Age for Out-of-Network Client (s). 10. Post-association steering decision maker: 2.4G RSSI measurements: Number of RSSI measurements on 2.4GHz band. 5G RSSI measurements: Number of RSSI measurements on 5GHz band. 11. Utilization Monitor Advanced Settings: RSSI avg probe requests: Number of probe requests required for the RSSI averaging. 2.4G check frequency(s): The frequency to check medium utilization on 2.4GHz .
12. Rate estimation: 5G RSSI difference: Difference when estimating 5GHz RSSI value from the one measured on 2.4GHz. 2.4G RSSI difference: Difference when estimating 2.4GHz RSSI value from the one measured on 5GHz. RSSI avg probe requests: Number of probe requests required for the RSSI averaging. Data rate estimate (s): Seconds between successive stats samples for estimating data rate.
purposes only). 11k active scan (s): Active scan duration used in 802.11k Beacon Report (s). 11k passive scan (s): Passive scan duration used in 802.11k Beacon Report request (s).
13. Steering Executor Advanced Settings: Abort steering time (s): Maximum time for client to associate on target band before AP aborts steering (s). Coalesce reject time (s): Time to coalesce multiple authentication rejects down to a single one (s). Max auth. Rejects: Max consecutive authentication rejects after which the device is marked as steering unfriendly. Unfriendly time (s): The base amount of time a device is considered steering unfriendly before another attempt (s).
2.4G RSSI assoc. (dB): RSSI threshold indicating 2.4GHz band is not strong enough for association (dB). 5G RSSI assoc. (dB): RSSI threshold indicating 5GHz band is not strong enough for association (dB). Autoremove blacklist (s): The amount of time (in seconds) before automatically removing the blacklist (s). BTM response wait (s): The amount of time to wait for a BTM response (s).
14. Steering Algorithm Advanced Settings Downlink rate (Mbps): Downlink rate (in Mbps) should exceed at least Low TxRateXingThreshold + this value, when steering from 2.4GHz to 5GHz due to overload.
4.0 FCC Statement: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device is restricted for indoor use. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25 cm between the radiator & your body.
