TN450A1 QUICK START & REGULATORY GUIDE TURBONET
Product Features:
Product Specification: Item Description System Processor Qualcomm MSM8960 Dual Core 1.5GHz Android OS Android Jeally Bean 4.2.2 Memory 1GB LPDDR2 SDRAM Storage Internal 8GB eMMC Flash (To be continued) Display, Camera and Scaning Size: 4.
Databar Expanded, Codeablock F, DataMatrix ECC200, DataMatrix ECC000-140, Aztec Code, Aztec Runes, Chinese Sensible Code, QR Code, Micro QR Code, Maxi Code, PDF 417, Micro PDF417, GS1 DataBar Composite, UPC/EAN Composite. Front Camera No Sensor OmniVision MT9E013 Resolution: 8MP (3264H*2448V) Rear Camera Angle of view: 74.
Battery Life 10 hours1 Reset Function Physical key under micro SD door (1) AC adaptor charging (via micro USB) Charging method (2) docking station charging (no sleeve charging) (3) battery cartridge Wireless charger (Optional) Qi (WPC V1.
Mechanical and Environment Dimension L 149.87 x W 80.24 x T 30.61 mm Weight 345g Ingress Protection IP65 Drop 1.5M on poly wood, 6 drops ESD Air: ±8KV Contact: ±4KV Operating 0°C~ 45°C battery in charging mode Temperature (include -20°C+60°C battery in discharging mode LCM and battery) Storage Temperature -20~+60°C Accessories (in package) Adaptor Jack 1pcs, 5.
Micro SD / MicroSIM Card Installation Open MicroSD/MicroSIM door, insert the Micro SD into slot. Insert Micro SIM into SIM slot. (Note: SIM 1 is set as default network connection; SIM switch: Go to “Settings” in Android system “SIM SWITCH” “Choose SIM” “SIM 2”) Close the door after installation.
Left LED blinks in red indicating low and risk battery and stating red indicating that the battery is charging. the LED becomes green when battery is fully charged, then. Power On TN450A1 Press and release the power button Note: Device turns to the modes as below by pressing power button key. Suspend Mode Press and release the power button to place the TN450A1 in suspend mode. In suspend mode the device turns off the display and goes into a low power state to conserve battery power.
Setting - Go to “BarcodeScan” Type: To choose Barcode type Barcode Scan
- Select “ Beep”: To have beep sound after scan - Select” Vibrate”: Need device vibration after scan Select” Automatic Carriage Return” Require to send enter key automatically after scan 2. Launch a bar code reading application or use Data Wedge. 3. Point the exit window at the bar code 4.
Select “P1” Select Remap Key
Choose “Barcode Scan” Select “P2” Remap Key choose “Barcode Scan” Scan Key(P1) (P2) 5. The red laser aiming pattern turn on to assist in aiming , scan ready when beep sounds. 6. Release the scan button.
Scan a Bar Code with Camera Using the rear camera to scan bar code. 1. Launch a bar code reading application or use Data Wedge. 2. Point the back of the TN450A1 at the bar code. 3. Press the scan button Photo & Videos Using the rear camera to take photos and capture video. Note: Ensure device memory or extend Micro SD card is space is available. GPS Information Acquiring satellite signals may take a few minutes.
NFC Detection Enable NFC Feature Go to “Settings” Tick “NFC”
Enable Android Beam Slide to “ON”
Regulatory Information Caution: Only use TURBONET approved accessories. Wireless Device Country Approval Regulatory markings, subject to certification, are applied to the device signifying the radio(s) are approved for use in the European countries under CE coverage. For 2.
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
particles ( such as grain, dust, or metal powders ) and any other area where you would normally be advised to turn off your vehicle engine. Safety in Aircraft Turn off your wireless device whenever you are instructed to do so by airport or airline staff. Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipment. Wireless devices should be switched off whenever you are requested to do so in hospitals, clinics or healthcare facilities.
Batty Safety The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non -commercial environment. Follow battery usage, storage, and charging guidelines found in the user guide. Improper battery use may result in a fire, explosion, or other hazard. To charge the device battery, the battery and charger temperature must be between 0℃~+50℃ Do not use incompatible batteries and chargers.
® Italy requires a user license for outside usage. Bluetooth Wireless Technology for use through the EEA has the following restrictions: Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.4835 GHz France, outside usage is restricted to 10mW EIRP Italy requires a user license for outside usage.