WebSTAR Cable Resident Gateway User’s Manual
WebSTAR Cable RG User Manual - ii -
WebSTAR Cable RG User Manual Safety Notes For Installation Use only the type of power source indicated on the marking labels. Use only the power adapter supplied with the product. Do not overload wall outlet or extension cords as this may increase the risk of electric shock or file. If the power cord is frayed, replace it with a new one. Proper ventilation is necessary to prevent the product overheating.
WebSTAR Cable RG User Manual Contents Chapter 1: Overview .........................................................................................................................................1 1.1 Physical Outlook .................................................................................1 1.1-1 Front Panel ............................................................................1 1.1-2 Rear Panel .............................................................................
WebSTAR Cable RG User Manual 5.5-3 5.5-3 5.5-3 5.5-3 5.5-3 5.5-3 Firewall-Time of Day Filters .................................................... 44 Firewall-Event Logging .......................................................... 45 Wireless-Basic...................................................................... 46 Wireless-Privacy .................................................................. 47 Wireless-Access Control ....................................................... 48 Wireless-Advanced.
WebSTAR Cable RG User Manual Chapter 1: Overview 1.1 Physical Outlook 1.1-1 Front Panel The following illustration shows the front panel of the WebSTAR Cable RG. LED Indicators The LEDs on the front panel are described in the table below (from left to right): LED Color Status Off Wireless PC Cable Green Green Green SEND Green RECEIVE Green POWER Green Blinking Description Power off or the initial test is over. To indicate wireless data traffic. On Wireless interface is in use.
WebSTAR Cable RG User Manual 1.1-2 Rear Panel 12VDC: RST︰ 12V Power connector Reset-to-Default push button ETHERNET︰ Ethernet 10/100BaseT RJ-45 connector USB： USB Connector CABLE︰ ANTENNA: F-Connector Standard 2.
WebSTAR Cable RG User Manual Chapter 2: Installation 2.1 Connecting the WebSTAR Cable RG to Your Computer 2.1-1 Installation Procedure for Ethernet Interface Follow the steps below for proper installation: 1. Make sure your computer meets the system requirements. 2. Connect a coaxial cable (supplied by the local Cable Television Company) to the CABLE connector on the modem. 3. Plug the power adapter into the POWER connector of the modem. 4. Plug the other end of the power adapter into a power outlet. 5.
WebSTAR Cable RG User Manual 2.1-2 Installation Procedure for USB Interface Follow the steps below for proper installation: 1. Make sure your computer meets the system requirements. 2. Connect a coaxial cable (supplied by the local Cable Television Company) to the CABLE connector on the modem. 3. Plug the power adapter into the POWER connector of the modem. 4. Plug the other end of the power adapter into a power outlet. 5. Check CABLE LED. If it is solid ON, the Cable Modem is on-line now.
WebSTAR Cable RG User Manual 2.1-3 Installation Procedure for Wireless 1. 2. 3. 4. 5. 6. Make sure your computer meets the system requirements. Connect a coaxial cable (supplied by the local Cable Television Company) to the CABLE connector on the modem. Plug the power adapter into the POWER connector of the modem. Plug the other end of the power adapter into a power outlet. Check CABLE LED. If it is solid ON, the Cable Modem is on-line now. If it is not, contact your service provider.
WebSTAR Cable RG User Manual Chapter 3: Software Installation and Configuration 3.1 USB Driver Installation 3.1-1 For Windows 98/Me 1. Wait for the cable modem is running in the operational state (registration O.K.). Plug the USB cable into your PC USB port. You will see the next page. Click the “Next” button. 2. Select “Search for the best drivers for your device“ and click the “Next” button. 3. Check “Specify a location” and browse CD-ROM:\Win9x or WinME. Click the “Next” button.
WebSTAR Cable RG User Manual 4. Select “The updated driver...” and click the “Next” button. 5. Click the “Next” button. 6. Installation has been completed here. Click the “Finish” button.
WebSTAR Cable RG User Manual 7. The system will ask you to restart your computer. Click “Yes” to complete the installation. 3.1-2 For Windows 2000/XP 1. Wait for the cable modem is running in the operational state (registration O.K.). Plug the USB cable into your PC USB port. 2. You will see the next page. Click the “Next” button. 3. Select “Search for a suitable driver for my device“ and click the “Next” button.
WebSTAR Cable RG User Manual 4. Insert the driver CD into CD-ROM. Select “CD-ROM drive” and clicks the “Next” button. 5. Click the “Next” button. 6. Installation has been completed here. Click the “Finish” button.
WebSTAR Cable RG User Manual 3.2 Uninstall USB Driver 3.2-1 For Windows 98/ME 1. 2. 3. 4. 5. Click “Start” button on your computer’s taskbar, point to “Settings”, and then click “Control Panel”. Select Add/Remove Programs. On the Install/Uninstall tab, select USB Cable Modem Adapter from the list box. Click the Add/Remove button. A confirmation dialog appears. Click Yes. A dialog box appears to ask you unplug USB cable, please unplug the cable and click OK. 3.
WebSTAR Cable RG User Manual 3.3 Setting TCP/IP on Client PC After you successfully complete the network interface card (Ethernet card) installation task, you need to make sure the TCP/IP communications protocol used by the Ethernet card is installed and correctly configured on your system. 3.3-1 For Windows 98/Me 1. Click on the Start menu, point to Settings and click on Control Panel. 2. The Control Panel window will show up. Double-click the “Network” icon in the Control Panel window. 3.
WebSTAR Cable RG User Manual 4. The Select Network Component Type dialog box will show up. Click ”Protocol”, and then click ”Add”. 5. You will see the Select Network Protocol dialog box. Click “Microsoft” in the “Manufactures:” list, and then click “TCP/IP” in the “Network Protocols:” list. Click “OK”.
WebSTAR Cable RG User Manual 6. 7. 8. You will be directed back to the Network dialog box, and on the “Configuration” tab, the entry that includes TCP/IP -> followed by the Ethernet card installed in your computer will appear in the list of installed network components. Click TCP/IP -> followed by the Ethernet card installed in your computer, and then click ”Properties”. The TCP/IP Properties dialog box will appear.
WebSTAR Cable RG User Manual 9. Click “Gateway” to bring it to the front. On this tab, leave the “New gateway:” blank. If there is the entry in the “Installed gateway:” list, click it and then click “Remove” to remove all installed gateways. 10. Click “DNS Configuration” tabs to bring it to the front, and click “Disable DNS”, then click “OK” to close the dialog box.
WebSTAR Cable RG User Manual 11. The Copying Files dialog box will pop up and the system will start copying files from Windows. At the first time you will be asked to insert the Windows 98 CD-ROM into the CD-ROM drive during the files copying, and follow the instructions when they show up, then click “OK”. It will prompt another Copying Files dialog box. Please type the command line that Windows files located in the dialog box (For example, D:\win98). Click “OK” to continue the files copying. 12.
WebSTAR Cable RG User Manual 2. The Network and Dial-up Connections window will show up. Double-click “Local Area Connection” icon in the Network and Dial-up Connections window. 3. The Local Area Connection status window will show up. Click the “Properties” button. 4. Click “Internet Protocol (TCP/IP)” and then click “Properties”.
WebSTAR Cable RG User Manual 5. The Internet Protocol (TCP/IP) Properties dialog box appears. Click “Obtain an IP address automatically”. Click “Obtain DNS server address automatically”. Click “OK” to close the dialog box. 6. Windows will appear the System Settings Change dialog box and ask you if you would like to restart your computer. Click “Yes”.
WebSTAR Cable RG User Manual 3.4 DHCP Server PC connected to the cable modem can automatically get a private IP address from the DHCP server of cable modem before cable modem is on line. The following steps will show you how to get an IP address from DHCP server of cable modem before cable modem is on line. 3.4-1 For Windows 98/Me 1. Click “Start“, point to “Run“, and click to open the “Run“ windows. 2. Enter “winipcfg“ in the “Open“ field.
WebSTAR Cable RG User Manual 3.4-2 For Windows NT/2000/XP 1. Click “Start“, point to “Run“, and click to open the “Run“ windows. 2. The Run dialog box appears. Type “cmd” in the “Open” field, and then click “OK” to execute the command. 3. You will enter the dos mode, type “ipconfig”, press “Enter” on your keyboard, and you will see the IP address your computer get from the cable modem.
WebSTAR Cable RG User Manual 4. If PC is not access Internet, type “ipconfig /release”, and press “Enter” on your keyboard to release the IP. 5. Type “ipconfig /renew”, and press “Enter” on your keyboard to renew the IP. You can repeat the steps until your computer gets the correct IP. 3.4-3 For Apple Macintosh 1. Click “Apple menu“, point to “Control Panels“, and click “TCP/IP” to open the “TCP/IP” window.
WebSTAR Cable RG User Manual 2. If the iMac gets an invalid IP, select “Using DHCP Server” in “Configure” field. Click the “Close box” at the upper left corner to close the “TCP/IP” window. 3. Click the “Save” in the prompted message box. 4. You need to wait about 2 minutes and open “TCP/IP” window to see the new TCP/IP status. 3.5 Renew PC IP Address There is a chance that your PC does not renew its IP address after cable modem is on line and the PC cannot access the Internet.
WebSTAR Cable RG User Manual 2. Enter winipcfg in the “Open“ field. Click “OK“ to execute the winipcfg and show the “IP Configuration“ window. 3. Select the “Ethernet adapter“ to show the IP address. Press “Release“ and “Renew“ to get a new IP address from your ISP’s server. 4. Select the “OK“ to close the IP Configuration window.
WebSTAR Cable RG User Manual Chapter 4: Access Internet through Cable Modem For making sure that you can get into Internet successfully, please make sure the following first. 1. Make sure the connection (through Ethernet or USB) between the cable modem and your computer is OK. 2. Make sure the TCP/IP protocol is set properly. 3. Subscribe to Cable Television Company and get the license to access Internet. 4. Prepare wireless LAN Card if you would like to access Internet without Cat.5 UTP Cable.
WebSTAR Cable RG User Manual Chapter 5: Web Manager Once your host PC is properly configured, please proceed as follows: Start your web browser and type the private IP address of the cable modem in the URL field: 192.168.0.1. Type the IP address as the figure shown below.
WebSTAR Cable RG User Manual 5.
WebSTAR Cable RG User Manual 5.
WebSTAR Cable RG User Manual 5.
WebSTAR Cable RG User Manual 5.
WebSTAR Cable RG User Manual 5.5 Setup There are many functions could be adjusted by users under the Setup page. Here we will describe them in detail in the following pages. There are functions of Basic Settings, Advanced Settings, Firewall, and Wireless.
WebSTAR Cable RG User Manual 5.5-1 Basic Settings- Password Settings Password Settings: The Password screen allows you to change the password. If you do not change the password, all users on your network will be access the WebSTAR Cable RG simply by entering the unit’s IP address into their web browser’s location windows and entering the default password to access the WebSTAR Cable RG. If you want to change the Web Access Password, type the new one and re-enter it.
WebSTAR Cable RG User Manual 5.5-1 Basic Settings- Network Configuration Network Configuration: LAN IP Address: You have to provide a LAN IP Address for the Local Network. The LAN IP Address can be adjusted according to your local networks. Please consult the TCP/IP settings mannual, or use the default LAN IP Address. Host Name & Domain Name: These fields allows you to supply a host and domain name for the Router. Some ISPs require these names as identification.
WebSTAR Cable RG User Manual 5.5-1 Basic Settings- IP Address Management IP Address Management: DHCP Server: In this event, you can enable the DHCP server function of Cable RG. Once you enable it, your Cable RG will serves as a DHCP servers for your local network. Your local network will get the IP addresses automatically from the Cable RG.
WebSTAR Cable RG User Manual 5.
WebSTAR Cable RG User Manual 5.
WebSTAR Cable RG User Manual 5.5-2 Advanced Settings- Options Options: This function provides you the security of your local network. It will block all the outcoming packages that might attack your local network. To fully block the outcoming packages, Click on Enable. Then yours Cable RG will enable WAN Blocking. WAN Blocking: IPsec Pass/Through: This feature lets you use IPsec Pass Through. The IPsec Pass Through allows the certain packages to pass through the Cable RG.
WebSTAR Cable RG User Manual 5.5-2 Advanced Settings- IP Address Filtering IP Filtering: IP Filtering blocks specific internal users from accessing the Internet and enable VPN( virtual Private Network) tunnels. This is handled from the filtered tab shown above, and you can set up IP filtering by using IP address. Start Address: Enter the Start IP address of the range. End Address: Enter the End IP Address of the range. Enable: Click on Enable to enable it. The range of the IP addresses will be filtered.
WebSTAR Cable RG User Manual 5.5-2 Advanced Settings- Mac Filtering MAC Filtering: MAC Filtering blocks specific internal users from accessing the Internet and enable VPN( virtual Private Network) tunnels. This is handled from the filtered tab shown above, and you can set up MAC filtering by using MAC address. MAC Address Filters: Enter the MAC Addresses of the clients that you want to filter. Ex.
WebSTAR Cable RG User Manual 5.5-2 Advanced Settings- Port Filtering Port Filtering: Port Filtering blocks specific internal users from accessing the Internet and enable VPN( virtual Private Network) tunnels. This is handled from the filtered tab shown above, and you can set up Port filtering by using Port numbers. Start Port: Enter the Start port number of the range. End Port: Enter the End port number of the range. Protocol: On the same line, select TCP, UDP or Both.
WebSTAR Cable RG User Manual 5.5-2 Advanced Settings- Port Forwarding Port Forwarding: From the Forwarding tab, you can set up public services on your network, such as web servers, ftp servers, or E-mail servers. When users send this type of request to your network via the Internet, the Server will forward those requests to the appropriate PC.
WebSTAR Cable RG User Manual 5.5-2 Advanced Settings- Port Triggers Port Triggering: Port Triggering allows the Router to watch outgoing data for specific port numbers. The IP address of the computer that sends the matching data is remembered by the Router, so that when the request data returns through the firewall, the data is pulled back to the proper computer by way of IP address and port mapping rules. Triggerred Range: Enter the Start Port and the End Port.
WebSTAR Cable RG User Manual 5.5-2 Advanced Settings- DMZ Host DMZ Host: From the DMZ Host screen, you can allow one local user be exposed to the Internet to use a special –purpose service such as Internet gaming or videoconferencing. Whereas IP Forwarding can only forward a maximum of ten ranges of ports, DMZ hosting forwards all the points for one PC simultaneously. DMZ Address: To exposure one computer, enter the computer’s IP address. After the settings is done, click Apply to enalbe it.
WebSTAR Cable RG User Manual 5.5-2 Advanced Settings- RIP Setup RIP Setup: With RIP Setup screen shown above, you have to manually adjust to physical changes in the network’s layout. The Router, using the RIP protocol, determines the network packet’s route based on the fewest number of hops between the source and the destination. The RIP protocol regularly broadcasts routing information to other routers on the network. To set up RIP table, please follow the settings.
WebSTAR Cable RG User Manual 5.5-3 Firewall- Web Filters Web Filters: Web filters feature the blocking of the webs with certain keyword or domain. It can also filter the Proxy,Cookies,Java Applets,ActiveX,Popup Windows,Firewall Protection on webs. The administrator of the Cable RG can decide all the web filters’ contains. Give the keyword List and the Domain List and the Gable RG will filter them before accessing those webs with these keywords or domains.
WebSTAR Cable RG User Manual 5.5-3 Firewall- Time of Day Access Filter Time of Day Filter: This Screen features the blocking of all traffic for certain computers. Enter their MAC Address that you want to block by time and date. Select the blocking date and time range. And the administrator can also add or remove the computer list by their MAC addresses. After the settings is done, click on Apply to enalbe it.
WebSTAR Cable RG User Manual 5.5-3 Firewall- Event Logging Event Logging: The Event Log can send firewall attack reports out in two different ways. Individual emails can be sent out automatically, each time the firewall is under attack, and also a local log is stored within the modem and displayed in table form on the Event Log page. So enter the Contact Email Address and the SMTP Server. Click Enable to enable Event Logging function. After the settings is done, click on Apply to enalbe it.
WebSTAR Cable RG User Manual 5.5-4 Wireless- Basic Basic: Service Set Identifier(SSID): Enter the SSID for your service provider. The default SSID is wireless. New Channel: Select the channel for your service provider. The default channel is 1. After the settings is done, click on Apply to enalbe it.
WebSTAR Cable RG User Manual 5.5-4 Wireless- Privacy Privacy: Encryption Mode: There are No Encryption, 64-Bit Encryption and 128-bit Encryption respectively. WEP Passphrase : you can type any characters and generate into HEX type. Dafault key: Select the number as the default key for WEP encryption. Key 1 ~ Key 4: Please enter HEX type characters that you want to set for the WEP encryption. For 64-Bit Encryption, enter 10 characters in HEX type; for 128-bit Encryption, enter 26 characters in HEX type.
WebSTAR Cable RG User Manual 5.5-4 Wireless- Access Control Access Control: Authentication: There are three authetication types: Open System, Shared key and Open System or Shared key. This should be considered with the WEP (Wired Equivalent Privacy) mechanism. Close Network: Select ON To close the wireless clients’ network, or OFF to cancle it. Access List: Enter the MAC Address of the wireless clients that you would like to restrict or allow their access of network.
WebSTAR Cable RG User Manual 5.5-4 Wireless- Advanced Advanced Wireless Settings: Basic Data Rates: It decides the speed of the management packet transmission. Supported Rates: It decides the speed of the data packet transmission. Beacon Interval: Enter the beacon interval number. The range is from 0 to 65535 ms and the default is 100 ms. DTIM Interval: Enter the DTIM interval number. The range is from 1 to 255 ms and the default is 1 ms. Fragmentation Threshold: It decides the packet size.
WebSTAR Cable RG User Manual Chapter 6: Troubleshooting If the suggested solutions in this section do not resolve your issue, contact your system administrator or Internet service provider. Can I use the same cable line for TV and cable modem? A. Yes, the TV and cable modem uses the cable line. You need a splitter to use them at the same time. Ask Cable Company to install the splitter for you to avoid signal degradation.
WebSTAR Cable RG User Manual Appendix: Specification Specifications Cable RF: Downstream Upstream Operating Frequency Range 69-873MHz 5-55MHz Frequency Channel HRC, IRC, STD Frequency Selection Auto Scanning Controlled by Headend Bandwidth 6MHz Programmable (200*N KHz) N=1, 2, 4, 8, 16, 32 Characteristic Impedance 75Ω Nominal 75Ω Nominal Signal Level Range -15 to +15dBmV/64QAM A-TDMA: -15 to +15dBmV/256QAM +8 to +58dBmV/QPSK +8 to +55dBmV/(8,16)QAM +8 to +54 dBmV/(32,64)QAM S-CDMA: +8 to
WebSTAR Cable RG User Manual Wireless: Media Access Control • CSMA/CA with ACK Data Rate (Auto Fallback) • 11 Mbps • 5.5 Mbps • 2 Mbps • 1 Mbps Encryption • 64/128 bit WEP Frequency Range • 2.4 GHz ~ 2.4835 GHz Modulation • Barker (1Mbps) • Barker (2Mbps) • CCK (5.
WebSTAR Cable RG User Manual LED Pattern: Power • ON: Power ON • OFF: Power OFF RX • Flashing: RF DS Traffic TX • Flashing: RF US Traffic STATUS • ON: Operation • Flashing 1 time per sec: DS Scanning • Flashing every 2 sec: US Ranging • Flashing 4 times per sec: DHCP/TFTP Registration PC WIRELESS • ON: USB Link / Driver Loaded and Functional • Flashing: USB Traffic • OFF: No USB Link or PC Off • ON: Wireless Module Functional • Flashing: Wireless Traffic • OFF: No Wireless M
