User's Manual

F
L R
B
Right Bank Trim
Left Bank Trim
F
L R
B
NOTE: The use of the Trim buttons are accompanied with a Beep tone. A single long Beep indicates the
product is center trimmed. Continuous long Beeps indicate the product is trimmed to the maximum on a
particular side.
UNDERSTANDING TRIM ADJUSTMENTS
Forward/Backward Trim
• If your Neutron™ is moving forwards or backwards automatically, you may need to adjust the
FORWARD/BACKWARD TRIM buttons.
• If your Neutron™ flies forward, push and release the BACKWARD TRIM (B)button repeatedly until the
moving stops and proper flight is maintained.
• If your Neutron™ flies backwards, push and release the FORWARD TRIM (F)button in the same
manner until the problem is resolved.
• From time to time you may have to adjust the FORWARD or BACKWARD TRIM buttons to ensure the
Neutron™ will hover in mid-air and respond accurately to your commands.
Banking Left/Right Trim
�• If your Neutron™ is not steadily hovering and is banking to the left or right automatically, you
may need to adjust the LEFT BANK or RIGHT BANK Trim buttons.
• If your Neutron™ banks to the left, push and release the RIGHT BANK TRIM (R)button repeatedly until
the banking stops and proper flight is maintained.
• If your Neutron™ banks to the right, push and release the LEFT BANK TRIM (L) button in the same
manner until the problem is resolved.
• From time to time you may have to adjust the LEFT and RIGHT BANK TRIM to ensure the Neutron™
will steadily hover in mid-air and respond accurately to your commands.
SPEED SELECT BUTTON
The Neutron™ has 3 speed settings; SLOW, MEDIUM and HIGH. The Default setting when you first turn
on your Neutron™ is the SLOW speed mode. To increase the speed simply depress the speed setting
button (see diagram G) you will here a beep and the speed setting indicator light bar will show you
what speed setting you are on by the number of lights that are lit-up (see diagram H). One light
indicates slow, 2 lights indicates medium speed and all 3 lights lit up indicate full or fastest speed.
NOTE: When in 3CH mode, the speed setting indicator bar will light its LEDs from Left to Right
(see diagram H). When in 4CH mode the speed setting indicator bar will light it’s LED’s from Right to Left
(see diagram I) This is a helpful reminder as to what control channel mode you are flying in.
RECOGNIZING THE FRONT AND BACK OF THE COPTER
Even though the copter has four rotors there is still a front or "forward" facing direction and "back" or
backwards facing direction. The forward Front and forward facing direction of the Quadrocopter is the
side with two white blades (see diagram F ). The rear and back of the Quadrocopter is where the
charging socket and the two black propellers (see diagram F).
NOTE: The front of the Quadrocopter displays WHITE LED lights and the back of the copter displays RED LED
lights.
3/4 CHANNEL SELECT
Neutron™ allows you to control your Quadrocopter in 3 channel mode (beginner) or 4 channel mode
(advanced flying). The Neutron™ default setting is 4 Channel mode.
To change to 3 Channel mode:
PRESS and hold the 3CH button (see remote diagram on pg 3), you will hear 3 short beeps indicating the
Neutron™ now is set to 3CH mode.
To change back to 4 Channel mode:
PRESS and hold the 4CH button (see remote diagram on pg 3), you will hear 4 short beeps indicating the
Neutron™ is now set to 4CH mode.
Forward Trim
Backward Trim
Forward/Backward
Trim Controls
Push and release
to go backward
If flying forward... If flying backward...
Push and release
to go forward
Left/Right Banking Controls Push the left button to
increase left banking
sensitivity
Push to right button to
increase right banking
sensitivity
5 6
F
L R
B
Speed button
F
L R
B
L R
F
B
Front
F
G H
F
L R
B
I