Specifications

Operating Manual - NE Two Channel Power Amplifiers
10
7) Pluggable Output DSP Tools - Output DSP tools are the same as those available to the inputs.
8) Output Mute Button - Mutes the output.
9) Output Channel Name - The user can name each output channel.
10) Output Channel Number - Right click on this to bring up Clear, Copy, Link, and Sub Preset functions for that output channel.
6. SPECIFICATIONS
GENERAL POWER AMPLIFIER SPECIFICATIONS
Power Output Per Channel
Stereo Mode, Both Channels Driven . . . . . . . . . . . . . . . . . . . . . . . . . . . . ne 800 ne 1600 ne 2400
8Ω , 20Hz-20kHz 1%THD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225W . . . . . . . . . .450W . . . . . . . . . 700W
4Ω , 20Hz-20kHz 1%THD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400W . . . . . . . . . .800W . . . . . . . . . 1200W
Bridge Mode
8Ω , 20Hz-20kHz 1%THD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800W . . . . . . . . . .1600W . . . . . . . . 2400W
25V (ne 800 only), 70V, and 100V models . . . . . . . . . . . . . . . . . . . . . . 400W . . . . . . . . . .800W . . . . . . . . . 1200W
20Hz-20kHz 1%THD, per channel
Line Current Draw (both channels driven 4Ω /Ch, 120VAC Mains)
Line Current, Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200mA . . . . . . . . .165mA . . . . . . . . 200mA
Line Current, Idle (no signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475mA . . . . . . . . .500mA . . . . . . . . 475mA
Line Current, Typical (1/8 power pink noise) . . . . . . . . . . . . . . . . . . . . 2.81A. . . . . . . . . .4.95A . . . . . . . . . 6.75A
Line Current, Maximum (1/3 power sine wave) . . . . . . . . . . . . . . . . . . 4.93A. . . . . . . . . .8.80A . . . . . . . . . 12.6A
Thermal Dissipation (BTU/hr, both channels driven 4Ω /Ch)
BTU/hr, Standby mode, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 . . . . . . . . . . . .40 . . . . . . . . . . . . 40
BTU/hr, Idle (no signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 . . . . . . . . . . .109 . . . . . . . . . . . 109
BTU/hr, Typ (1/8 power pink noise) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 . . . . . . . . . . .447 . . . . . . . . . . . 682
BTU/hr, Max (1/3 power sine wave) . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 . . . . . . . . . . .466 . . . . . . . . . . . 717
Signal to Noise (20Hz-20KHz, unweighted) . . . . . . . . . . . . . . . . . . . . . . >107dB . . . . . . . .>110dB. . . . . . . . >112dB
Distortion (SMPTE, typical) - 8 ohm load, 10dB below rated power: . . . . . . . . . . . . . . . . .<0.5%
Distortion (THD-N, typical) - 8 ohm load, 10dB below rated power, 20Hz-20kHz:. . . . . . .<0.5%
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Hz-20kHz, +/-1dB
Damping Factor (8 ohm load, <1kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>250
Protea
ne
Two Channel Amplifier DSP Control Surface (DSP option must be installed)
(DSP control tab continued)