Model 61 PARTS MANUAL Version 4-04 Ashland Industries Inc. 1115 Rail Drive P.O. Box 717 Ashland, WI. 54806 Ph: 877-634-4622 Toll Free Ph: 715-682-4622 Fx: 715-682-9717 www.ashlandind.
Model 61 Scraper HOW TO ORDER PARTS: IMPORTANT Parts must be ordered through your local authorized ASHLAND dealer. Be sure to state MODEL and SERIAL NUMBER of your machine, PART NUMBER, DESCRIPTION and QUANTITY needed. Unless this is done, we cannot provide prompt service or assure shipment of the correct parts. Ashland Industries weldable replacement parts are availabe to rebuild, modify or update your scraper to current factory specifications. INDEX Page Page Page Page Page Page Page Page Page Page 3.
SAFETY SIGNAL WORDS Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The appropriate signal word for each has been selected using the following guidelines: DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations typically for machine components which, for functional purposes, cannot be guarded.
MODEL 61 SCRAPER ASSEMBLY INSTRUCTIONS 1. A suitable hoist or lift should be available for assembly. 2. Pack wheel bearing with grease and install hubs to rear spindles and front axle assembly. Be sure to follow the bearing numbers as shown in the parts listing as the front hubs require different bearings than the rear. 3. Raise actuating frame over bucket and lower into place so that the holes in the arms of the actuating frame align with the rear hole on each side of the bucket.
11. Connect a ½” x 38” hose from the front port of each cylinder to the remaining pipe line on the rear cross frame. 12. Raise the rear of the frame and install wheels to hubs. Also install wheels to front axle assembly. 13. Raise front of frame and remove the two 5/8” x 4” bolts which hold the cast socket halves inside the gooseneck. Remove the cast socket halves. 14. Roll the pole and axle assembly directly under the gooseneck, place the cast socket halves around the ball socket on the axle.
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 PART NO.
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PART NO.
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO.
10 9 KEY NO. 1 2 3 * 4 5 6 7 8 PART NO.
* (Serial number break) KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. A4520 A4512 A4513 A4514 A4515 A4519 A2239 *A4521A *A125047 A2235 A2234 A2233 DESCRIPTION Spindle, rear with flange Grease seal ( National 415082 ) Bearing cone, inner ( Timken 3784 ) Bearing cup, inner ( Timken 3720 ) Hub, with bearing cups Wheel bolt Washer, special 7/8" flat Cotter pin Wheel, 20" D.C. (up to sn 20667) Dec 2002 Wheel, 22.5” x 8.
CYLINDER KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. A516H118 PART NO.
Limited Warranty Statement Ashland Industries Inc. warrants each new product to be free from defects in material and workmanship. This warranty is applicable only for the normal service life expectancy of the product or components, not to exceed six consecutive months from the date of delivery of the new Ashland Industries product to the purchaser, or the date the product is first put into service via a rental agreement or other means, whichever occurs first.
