Models 45 & 50 PARTS MANUAL Version 4-04 Ashland Industries Inc. 1115 Rail Drive P.O. Box 717 Ashland, WI. 54806 Ph: 877-634-4622 Toll Free Ph: 715-682-4622 Fx: 715-682-9717 www.ashlandind.
Models 45S, 45D & 50S, 50D HOW TO ORDER PARTS: IMPORTANT Parts must be ordered through your local authorized ASHLAND dealer. Be sure to state MODEL and SERIAL NUMBER of your machine, PART NUMBER, DESCRIPTION and QUANTITY needed. Unless this is done, we cannot provide prompt service or assure shipment of the correct parts. Ashland Industries weldable replacement parts are availabe to rebuild, modify or update your scraper to current factory specifications.
OPERATORS AND MAINTENANCE INSTRUCTIONS This scraper is a durable piece of equipment and with proper care will yield many years of trouble free operation. The scraper requires a power source with TWO 4 way (double acting) hydraulic control valves. The scraper should be greased at all points where grease fittings are provided.
SAFETY SIGNAL WORDS Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The appropriate signal word for each has been selected using the following guidelines: DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations typically for machine components which, for functional purposes, cannot be guarded.
MODELS 45 & 50 SCRAPER ASSEMBLY INSTRUCTIONS 1. A suitable hoist or lift should be available for assembly. 2. Pack wheel bearing with grease and install hubs to rear spindles and front axle assembly. Be sure to follow the bearing numbers as shown in the parts listing as the front hubs require different bearings than the rear. 3. Raise actuating frame over bucket and lower into place so that the holes in the arms of the actuating frame align with the rear hole on each side of the bucket.
12. Raise the rear of the frame and install wheels to hubs. Also install wheels to front axle assembly. 13. Raise front of frame and remove the two 5/8” x 4” bolts which hold the cast socket halves inside the gooseneck. Remove the cast socket halves. 14. Roll the pole and axle assembly directly under the gooseneck, place the cast socket halves around the ball socket on the axle. Lower the frame into place so that the socket halves seat into the gooseneck.
KEY NO. 1 2 3 4 PART NO. A450H01 A450H02 A22H03 A45003 5 A4551 6 7 8 9 10 11 12 13 14 *** *** A4523 A2206 A4552 A40004 A40005 A5004 A022977-2 A022977-3 DESCRIPTION Hydraulic hose, 3/8" x 18" single braid Hydraulic hose, 3/8" x 38" single braid Swivel adapter, 90° Pin, 1-1/8" x 3-1/4", cotter both ends Cotter pin, 3/16" x 1-1/2" Frame, four wheel, Model D Bolt, 3/4 x 6" NC w/ nut & LW Hitch Bolt, 5/8" x 4" NC w/ nut & LW Grease fitting, 1-1/8" NPT strt.
KEY NO. PART NO.
KEY NO. 1 2 3 4 5 6 7 PART NO. A45005 A45006 8 9 10 11 A30002 A2502 A4524 A30003 A6007A A45007 A45008 DESCRIPTION Actuating frame Pin, 1-1/4" x 2-9/16" w/ locking head Bolt, 5/8" x 1-1/4" NC w/ lock nut Pin, 1-1/2" x 5-3/4" Capscrew, 1/2" x 1" NC w/ LW Pin, 1-1/8" x 6" Shoulder pin, 2-1/2" shoulder, 1-1/4" to 1" Nut, 1" NF lock nut Roller Cotter pin, 1/4" x 2" Pin, 1-1/4" x 4-1/8" w/ sq. head & hole for gr.
KEY NO. PART NO.
* (Serial number break) KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO. A4512 A4513 A4514 A4515 A2233 A4516 *A4521A *A125047 A4519 A2235 A4520 A2239 DESCRIPTION Grease seal ( National 415082 ) Bearing cone, inner ( Timken 3784 ) Bearing cup, inner ( Timken 3720 ) Hub, less bearing cups Bearing cup, outer ( Timken 14276 ) Bearing cone, outer ( Timken 14137A ) Wheel, 20" D.C. (Model 50 only: up to sn 20667, 12/02) Wheel, 22.5” x 8.
KEY NO. 1 2 3 4 5 6 7 8 9 10 PART NO. A300H03 A300H04 A300H05 A300H06 A300H07 A45H05 A45H03 A4524 11 12 13 14 A45H04 A300H11 A300H12 A22H15 A22H15A A300H13 A22H18 A22H17 A300H14B 15 16 17 A45003 DESCRIPTION Piston nut, 1" NF Cast iron ring, 4" OD Backup washer, 4" OD O-ring seal, 4" OD x 3/16" Piston, 4" Piston gasket, 1" Shaft, 1-1/2" dia.
KEY NO. QTY. PART NO.
Limited Warranty Statement Ashland Industries Inc. warrants each new product to be free from defects in material and workmanship. This warranty is applicable only for the normal service life expectancy of the product or components, not to exceed six consecutive months from the date of delivery of the new Ashland Industries product to the purchaser, or the date the product is first put into service via a rental agreement or other means, whichever occurs first.
