User manual
Table Of Contents
- 1. Introduction
- 2. Pre-Installation
- 3. Programming the VoWiFi Handset
- 4. Installation of VoWiFi Handsets
- 5. Maintenance
- 5.1 Handset
- 5.1.1 Configure Spare Handsets without a Number in Large Systems
- 5.1.2 Upgrade Handset Software
- 5.1.3 Upgrade Software OTA via TFTP
- 5.1.4 Upgrade Software via PDM
- 5.1.5 Upgrade Software Over the Air (OTA) via Centralized Device Management (IMS3)
- 5.1.6 Recapture the Earlier Software
- 5.1.7 Upgrade Handset Functionality using License
- 5.1.8 Perform a Factory reset
- 5.2 Replacement of Handsets
- 5.3 Change Number of a Handset
- 5.4 Update Parameters via IMS3
- 5.5 Perform a Security Upgrade via IMS3
- 5.6 Upgrade the Template
- 5.7 Create a Configuration Backup
- 5.1 Handset
- 6. Handset Configuration
- 6.1 Select Network
- 6.2 IP Address Settings
- 6.3 Network Settings
- 6.4 Security Settings
- 6.5 Handset Settings
- 6.5.1 Automatic key lock
- 6.5.2 Phone lock
- 6.5.3 Audio adjustment
- 6.5.4 Headset Configuration
- 6.5.5 In Charger Behavior
- 6.5.6 Configure Profiles
- 6.5.7 Hide Missed Call Window
- 6.5.8 Battery Warning
- 6.5.9 Shared Phone
- 6.5.10 Prevent Handset Switch off
- 6.5.11 Uploadable Language
- 6.5.12 Select Default Language
- 6.5.13 Short cuts
- 6.5.14 Soft Key Functions During Call
- 6.5.15 Import Contacts
- 6.5.16 Company Phonebook
- 6.5.17 Central Phonebook
- 6.6 Messaging and Alarm
- 6.7 Messaging Settings
- 6.8 Alarm Settings
- 6.9 Telephony
- 6.9.1 Endpoint ID and Endpoint number
- 6.9.2 VoIP Protocol
- 6.9.3 Codec
- 6.9.4 Offer Secure RTP
- 6.9.5 Internal Call Number Length
- 6.9.6 Emergency Number
- 6.9.7 Voice Mail Number
- 6.9.8 Message Centre Number
- 6.9.9 Max number of Call Completions
- 6.9.10 Dial Pause Time
- 6.9.11 Direct off Hook from Charger
- 6.9.12 Replace Call Rejected with User Busy
- 6.9.13 Busy on 1 / Disable call waiting
- 6.9.14 Calling Line Restriction
- 6.10 Regional Settings
- 6.11 Display
- 6.12 Menu Operation
- 6.13 Push-To-Talk (PTT) Group Call
- 6.14 Presence Management
- 6.15 Location
- 7. Use Handset to Verify the VoWiFi System Deployment
- 8. Handset Internal Web Administration Page
- 9. Administration
- 10. Troubleshooting
- 11. Related Documents
- 12. Document History
- Appendix A: Working with Templates
- Index
- Contents
TD 92675EN
20 June 2012 / Ver. E
Configuration Manual
Ascom i62 VoWiFi Handset
58
6. Handset Configuration
gives a more accurate location using a third-party Real-Time Location System (RTLS)
solution.
The following RTLS solutions are supported:
•Cisco RTLS Solution
In order to use the Cisco RTLS solution, a Cisco Mobility Services Engine must be used and
con
figurations in the handset are required.
•Ekahau RTLS Solution
In order to use the Ekahau RTLS solution,
the handset must ha
ve the Ekahau license (see
5.1.7 Upgrade Handset Functionality using License on page 18) and also be configured.
Additionally information about AP location and RTLS location, see Func
tion Description,
Location in Ascom VoWiFi System, TD 92607GB.
6.15.1 Configure Handset for Cisco/
Ekahau RTLS Solution
1 Select Location > Common.
2In the Location scanning drop-down list, select “Enable“.
3In the Scanning interval
1
field, set the time between the scanning periods.
4In the Scans per scanning period
1
drop-down list, select how many scans that should
be performed during each scanning period.
If the Ekahau RTLS solution is used, also perform the steps 5 - 8.
5
Select Location > Ekahau.
6In the EKAH
AU license drop-down list, select “Yes“. Additional parameters are shown.
7In the IP address field,
enter the IP address to the Ekahau location appliance.
8In the Listening port field, enter the port the location appliance is lis
tening to.
1. Note that close scanning periods, and frequently scans per period, will shorten the battery time.