User's Manual
Table Of Contents
- Contents
- 1 Introduction
- 2 Descriptions
- 3 Operation
- 3.1 Basic Operation
- 3.1.1 Call List
- 3.1.2 Make a Call
- 3.1.3 Answer a Call
- 3.1.4 End a Call
- 3.1.5 Transfer a Call
- 3.1.6 Turn Off Alert Signals at an incoming Call
- 3.1.7 Turn the Mute Mode during a Call Off/On
- 3.1.8 Loudspeaking Function
- 3.1.9 Increase/Decrease the Speaker Volume during a Call
- 3.1.10 Turn Audible Signals On/Off
- 3.1.11 Lock/Unlock the Keypad
- 3.1.12 Lock/Unlock the Handset
- 3.1.13 Switch the Handset On
- 3.2 Messaging
- 3.3 SMS (Short Message Service)
- 3.4 Interactive Messaging
- 3.5 Mobile Data
- 3.6 Conference Call
- 3.7 Push-to-talk
- 3.8 Alarm Operation
- 3.9 Automatic Call after an Alarm
- 3.1 Basic Operation
- 4 Navigate the Menu
- 5 Menu Tree
- 6 Menu Operation
- 6.1 Messages
- 6.2 Contacts
- 6.2.1 Find an Entry in the Local Phonebook
- 6.2.2 View an Entry in the Local Phonebook
- 6.2.3 Add an Entry to the Local Phonebook
- 6.2.4 Delete an Entry in the Local Phonebook
- 6.2.5 Edit an Entry in the Local Phonebook
- 6.2.6 Find an Entry in the Central Phonebook
- 6.2.7 Save a Number from the Call List to the Local Phonebook
- 6.2.8 Delete a Number in the Call List
- 6.2.9 Delete All Numbers in the Call List
- 6.3 Modes
- 6.4 Services
- 6.5 Settings
- 6.5.1 Change the Volume
- 6.5.2 Change the Ring Signal
- 6.5.3 Key Beep On/Off
- 6.5.4 Vibrator On/Off
- 6.5.5 Deactivate/Activate No-movement alarm
- 6.5.6 Deactivate/Activate Man-down alarm
- 6.5.7 Deactivate/Activate Pull-cord alarm
- 6.5.8 Edit a Soft key
- 6.5.9 Edit a Hot key
- 6.5.10 Select Language
- 6.5.11 Change Text Size
- 6.5.12 Lock the Handset Manually
- 6.5.13 Change the Lock Code
- 6.5.14 Clock Settings
- 6.5.15 Turn On/Off Automatic Keypad Lock
- 6.5.16 Enable/Disable Quick Answer
- 6.5.17 Set New Messages to be Displayed Upside down
- 6.5.18 Set Owner ID
- 6.5.19 Select PBX System
- 6.6 Additional Information
- 7 Advanced Functions
- 8 Operation Notice
- 9 Maintenance
- 10 Trouble Shooting
- Appendix A: 9d24 Mkll Functionality with a 9d23 SIM
- Index 92333GB
PRELIMINARY
TD 92333GB
2006-03-20/ Ver. PA8
User Manual
9d24 Mkll Cordless Telephone
10
3 Operation
3.1 Basic Operation
3.1.1 Call List
The twenty last received/dialled telephone numbers are stored in a call list. Open the call
list by pressing the Navigation key (down), or from the menu, see
6.2 Contacts on page
26. If the clock and date function is set, you can on the same day the call was received/
dialled, see the time for the call. The time stamp is changed to a date stamp the following
day.
3.1.2 Make a Call
Note: The headset answering button is only active during a call or when the telephone is
ringing and can thus not be used to get the line when making a call.
Pre-dial
Enter the number and press the Call key to get the line. The number is shown on the
display while dialling. If needed, you can press the Soft key “C” to erase and edit the
number. By using Navigation key (left/right) it is possible to step and add/delete a digit in
the middle of a number.
It is possible to turn on/off the tone sender in a predialled number by making a long press
on the *-key. Tone sender on will be indicated with a “T” in the number and off with “-”.
If a pause is required in the number, it is added by making a long press on the #-key. The
pause is indicated with a “P” in the number.
Post-dial
Press the Call key to get the line and enter the number. The number will not be added to
the call list when post-dial is used.
Dial using a pre-programmed Hot key or Soft key
A Hot key or Soft key can be programmed with a telephone number. Press the pre-
programmed Hot key or Soft key. The call will automatically be connected.
Dial a number from the Call list
Enter the call list with Navigation key (down), or from the menu. Select a number and
press the Call key.
The number in the call list can be edited before the call is started. Press “Edit”, make the
changes and press the Call key.
Dial a number from a Message
You can dial a number included in a received message by pressing the call key. The first
number in the message is dialled. If the message is stored in the message list, open the list
by pressing Navigation key (up). Select the message and press the Call key.